Godox UL150II User manual

静音LED摄影灯
Silent LED Video Light
说明手册
Instruction Manual
深圳市神牛摄影器材有限公司
地址: 深圳市宝安区福海街道塘尾社区耀川工业区厂房2栋 电话: [phone](8062)
传真: [phone] 邮箱: [e-mail]
www.godox.com
Made in China 705-UL1520-01
Add.: Building 2, Yaochuan Industrial Zone,Tangwei Community, Fuhai Street, Bao’ an District, Shenzhen
518103, China Tel: [phone](8062) Fax: [phone] E-mail: [email protected]m
GODOX Photo Equipment Co., Ltd.
合格证
QC PASS
|
神牛微信公众号
Wechat
Official Account

1 2
1.使用前必须阅读并理解产品说明书。
2.专业灯具，禁止儿童使用。当儿童靠近时，家长或陪护人必须密切监督，以免
儿童因碰撞灯具或私用灯具造成人身伤害。
3.本灯具并非普通照明灯具，不可用于普通照明，任何有过眼部损伤或眼部敏
感的人群均应避免使用本灯具。
4.灯具点亮时，必须小心使用，禁止接触高温部件，如LED灯珠，以免造成灼伤。
5.灯具点亮时，任何情况下均禁止直视灯珠。应该在专业灯光师指导下使用强
光，任何情况下避免长时间处于强光环境，如引起眼睛不适，请及时关闭灯具，
暂停使用，请及时就医。
6.倘灯珠损坏或因热变形，应停止使用，并及时联系制造商、服务代理商或合
格的维修人员更换灯珠，以免发生意外。
7.本产品仅适用于－20℃-40℃工作环境温度及正常湿度环境下使用。
8.请勿使用损坏的设备或设备配件，待专业维修人员检查维修，确认设备正常
方可使用。
9.在使用过程中，如果本产品由于跌落、受到挤压或遭受强烈冲击而造成外壳
破裂的，请勿继续使用，以免因接触到内部电子元件而受到电击伤害。
10.如需要延长线，请使用额定电流≥该设备额定电流的延长线。如延长线额
定电流小于该设备，可能导致过热。
11.部分产品电源线较长，请合理放置电源线，使其处于安全位置。避免电源线
接触过热物体表面、避免放置不当导致拉扯损坏或绊倒现场人员。请使用本厂
原装电源线，如使用非本厂电源线导致产品损坏，概不在本厂维修范围内。
12.在清洁和维修之前，请务必从电源插座上拔下该设备插头。不使用时，禁止
拉扯电源线以将设备插头从电源插座中拔出。正常断电，应是用手抓住该设备
插头两端，将插头从电源插座中拔出。此设备需连接到接地插座中。
13.本设备没有防水性能，请让设备保持干燥，请勿将本设备浸入水中或其他
液体中。设备需安装在干燥且通风处，避免在雨天、潮湿、多尘或过热环境下
使用。请勿将任何物体置于灯具上或使液体流入灯具内部，以免发生意外。
14.请勿私自拆卸产品，如产品出现故障，须由本公司或授权的维修人员进行
检查维修。
15.存放本设备之前，请确保设备已完全冷却。存放时，将电源线从设备上拔
出。设备应放置于设备便携包内或通风干燥处。
16.请勿将设备放置在酒精、汽油等易燃易挥发的溶剂附近。
17.本厂不推荐的产品附件，请勿使用，以免导致火灾、触电或人身伤害。
18.清洁本设备时，请勿用湿布擦拭，请用干布，软布擦拭设备污垢。
19.设备使用前，请注意将保护罩取下。
20.本产品已通过ROHS，CE，和FCC认证，请参考相关国家标准使用和操作。
21.安全说明依据本厂严格测试制定，设备设计和规格如有变更，恕不另行通
知。客户可以上神牛官网查看最新的电子版说明，了解产品最新资讯。
22.部分产品内置锂电池。此类产品请使用专用的充电器进行充电，并且按正
确的操作说明，在规定的电压、温度范围内使用。
23.部分产品使用电池供电。此类产品请勿使用说明书中未指定的任何电池、
电源或附件。请将电池和其他附件置于儿童及婴幼儿无法触及之处。如果儿
童或婴幼儿吞下电池或附件，请立刻就医。如果电池漏液、变色、变形、冒烟或
发出异味，请立刻将其取出。在取出过程中请小心，以免烫伤。如果继续使用，
可能会引起火灾、触电或皮肤烫伤。请勿使用任何变形或改造过的电池。请勿
拆卸或改造本产品或电池。请勿加热电池或焊接电池。请勿让电池与火或水
接触。请勿让电池受到强烈的外力撞击。请勿将电池的正负端错误插入，或将
新旧电池或不同类型的电池混合使用。
24.—年保修期，消耗品电池、适配器、电源线等配件不在此保修范围内。
25.经发现，擅自检修设备，将取消一年保修期，维修需要收取相关费用。
26.对于不规范操作引起的机器故障不在保修范围内。
重要的安全说明及注意事项
首先作为最基本原则：本产品为专业灯光布景设备，应由专业灯光师使用或在
专业人士指导下使用。使用时必须始终遵循基本的安全预防措施，具体安全预
防措施如下：
保存这些说明

3 4
前言
感谢您购买神牛产品！
静音LED摄影灯UL系列无风扇，零噪音，非常适用于直播拍摄、视频录制、采
访布光等多种拍摄场合。灯体与控制器分离，操作方便。光源稳定，显色性好，
功能强大。支持蓝牙APP无线分组调光，无极调节亮度。
请勿让儿童接触本产品。
使用前请将灯头保护罩取下。
请保持干燥，请勿用湿手接触产品，亦不可将产品浸入水中或暴露于
雨中。
请勿私自拆卸产品，如产品出现故障须由本公司或授权的维修人员进
行检查维修。
本产品不能防水，在雨天及潮湿环境下请注意防水。
请勿将光源对准人的眼睛，以免造成伤害。
请勿放置在超过40摄氏度的高温环境中。
请使用本厂原装电源线，由于使用非本厂电源线导致产品损坏，概不
在本厂维修范围内。
请勿在化学品、可燃性气体或其他特殊物质附近使用LED灯。
本灯具光源仅可由制造商、其服务代理商或相关合资格人员更换。
倘灯泡损坏或热变形，应及时更换。
本灯具仅供专业使用。
主要特点:
• 无风扇，零噪音，全功率输出稳定。
• 功率强劲，光源稳定，支持无极调节亮度（0％-100％）。
• V口电池供电或AC电源供电，室内室外两用。
• 灯体与控制器分离，操控更便捷，散热性更佳。
• 支持2.4G遥控器/蓝牙APP/DMX512控制台控制。
• U型支架设计，可吊装，调节各种角度更方便。
• 拥有12种模拟场景光效，自由营造光氛围。
• 标准保荣卡口，兼容各类光效附件。
警告
部件名称、
灯体
⑦
控制器
1.灯体
2.散热孔
3.保荣卡口
4.灯头保护罩
5.LED灯珠
6.伞孔
7.伞固定旋钮
8.U型支架
9.支架旋钮
10.支架套筒
11.把手
12. DC输入接口
13.卡口推制
①
②
⑪
⑨
⑨
⑨
⑧
⑧
⑬
③
⑤
⑫
⑦
⑥
④
⑩
⑩⑫
⑬
⑪
请勿直视光源。

5 6
①
②
③
④
⑤
⑥
灯体x1
5米电源线x1连接线x1 控制器固定件x1
灯头保护罩x1连接线固定绳x1
控制器x1
反光罩RFT-19x1
说明书x1
标配物品
可选配物品
可搭配本公司摄影附件使用，以获得最佳的拍摄效果和使用体验：
LED灯菲涅尔镜头,聚光筒，RC-A6遥控器，保险钢丝绳。
安装及拆卸指引
1. 连接控制器和灯体
按住连接线弹簧锁口按钮，将连接线一端插入灯体DC INPUT接口中。接着将
另一端插入控制器DC OUTPUT接口，即可完成控制器与灯体的连接。
5. /FX按键
6.DMX设置键
7.黑色拆卸电池按钮
8.V口电池座
9.AC INPUT接口
10.DC 48V接口
11.黄色拆卸电池按钮
12.DMX IN卡侬头接口
13.DMX OUT卡侬头接口
1.USB Type-A接口
2.SET调节旋钮
3.开关按键
4.MENU菜单按键

2. 安装到三脚架上
调整灯体到合适角度，旋转套筒旋
钮安装灯体在三脚架上，最后旋转
套筒旋钮固定灯体。可以通过拧松
支架旋钮，调整灯体拍摄角度,调整
完毕拧紧支架旋钮即可。
注:三脚架不包含在标配物品内,需
另购。
3. 将控制器安装到灯架上
先将控制器固定件把手拧松，然后
插入灯架，旋转把手拧紧控制器固
定件。最后将控制器V口对准控制器
固定件卡槽，插入即可。
提示：拆卸时，只需按住卡槽推制，
即可取下控制器。
4. 安装及拆卸灯头保护罩
安装：推动卡口推制至末端，将灯头
保护罩对准保荣卡口套上，最后顺
时针旋转套紧即可。
拆卸：推动卡口推制至末端，接着逆
时针旋转取出即可。
注：使用时，务必将灯头保护罩取出
，否则影响灯头散热，易损坏。不使
用时，套上灯头保护罩，以达保护灯
头效果。
5.安装及拆卸反光罩
安装：推动卡口推制至末端，将反光
罩对准保荣卡口套上，最后顺时针
旋转套紧即可。
拆卸：推动卡口推制至末端，接着逆
时针旋转取出即可。
连接DMX控制台
控制器DMX控制台连接操作示意图如下：
连接多台
供电方式
1. AC供电
AC100V-240V
注：连接线和电源线，在安装或拆卸时，均需要按住锁扣按钮，方可安装或
拆卸。
7 8
DMX512

显示屏
2. V口电池供电
注意：支持使用14.8V或26V的V口电池。只有带黄色拆卸电池按钮一边支持
单边供电。双电池供电时，其中一个电池低电量，另外一个电池即使满电，设
备依然无法正常工作。电池低电量时，对应的电池图标呈现闪烁状态。建议
使用双电池供电时，应先检查两个电池是否都有足够的电量。
2.4G无线 频道 组别 蓝牙
亮度数值
V口电池
电量显示
调光曲线 锁定功能显示
高温警告
V口电池
电量显示
控制器操作说明
1. 开关机
2. 亮度调节
3. 菜单设置
在主界面，旋转SET调节旋钮能够
调节亮度大小，调节范围为0％-100
％。顺时针旋转增加亮度值，逆时针
旋转减少亮度值。常规旋转，增加或
减少1个单元值；快速旋转，增加或
减少10个单元值。
注：在主界面时，短按一次SET调节旋钮，
可关闭灯体亮度，再次按动一次SET调节
旋钮，可恢复之前的亮度值。
3.1 无线
在无线界面，依序排列着无线开关、
频道、组别、识别号。
通过短按SET调节旋钮进行选择，
选择完毕旋转SET调节旋钮进行设
置，即可完成无线开关、频道、组别、
识别号等一系列设置。
接通电源，长按1秒控制器开关按键，
实现开机或关机。
短按<MENU>菜单按键，进入菜单界面，界面依序排列着无线、蓝牙、DMX、调
光曲线、屏幕亮度、语言、恢复出厂设置、版本与升级。
在菜单界面中，通过旋转SET调节旋钮进行选择，接着短按SET调节旋钮，可
进入对应的设置界面。
9 10

3.6 语言
在语言设置界面，旋转SET调节旋
钮选择English或简体中文。
3.2 蓝牙
在蓝牙设置界面，依序排列着蓝牙
开关、重置及蓝牙MAC码。
通过短按SET调节旋钮进行选择，
选择完毕旋转SET调节旋钮进行设
置，即可完成蓝牙开关、蓝牙重置设
置。
扫描此二维码即可下载“Godox-
Light”手机APP(安卓和苹果系统
都可以使用)。
注:首个移动设备(手机或平板电脑)可直接使用APP操控灯体。更换其他移动设备时,灯体
进行蓝牙重置(Reset)后,方可正常使用APP。
3.3 DMX模式
在DMX设置界面，界面显示地址通
道，旋转SET调节旋钮选择地址：
OFF/1-512。当选择OFF，灯体关闭
DMX模式。当选择1-512，灯体开启
DMX模式。选择完毕，短按SET调节
旋钮可返回上一级菜单界面。
n+3
n+4
n+5
0-85：光效档位Ⅰ
86-171：光效档位Ⅱ
172-255：光效档位Ⅲ
DMX实用表
地址
码
运行
模式 CCT FX 备注
n(模式） 0-51 52-255
n+1 DMX*(100/255) 取整
数 0-100%亮度调节
DMX*(100/255) 取整
数 0-100%亮度调节
n+2 DMX*(光效总数/255)
3.4 调光曲线
在调光曲线设置界面，旋转SET调
节旋钮可依次选择线性/S型/指数/
对数等调光曲线。
3.5 屏幕亮度
在屏幕亮度设置界面，旋转SET调
节旋钮可依次选择1、2、3档屏幕亮
度值。
MAC:F463
线性
11 12
例如:光效总数8，DMX=160,
光效号=160*8/255=5

注: 当旋转到闪光灯、雷闪电、坏灯泡、电视机等情景光效模式时，短按SET调
节旋钮可进行速率(I、II、III)变换和亮度调节(0％-100％)。
小提示： 长按3秒< >按键可实现锁定/解锁功能。
短按< >按键进入FX情景光效界面。旋转SET调节旋钮依次选择闪光灯、
雷闪电、坏灯泡、电视机等12种情景光效。
3.7 恢复出厂设置
在恢复出厂设置界面，旋转SET调
节旋钮选择“是”或“否”，短按SET
调节旋钮确认选择。选择“是”后，灯
体启动重置程序，显示屏显示重置
进度条。重置完毕跳回主界面。
注：恢复出厂设置后，亮度值为100％。
当连接线没有连接好灯头或者控制
器，显示屏出现连接线与设备分离
图示，此时建议检查一下两处地方：
控制器连接处是否连接和灯头连接
处是否连接。
3.8版本与升级
在版本与升级界面，显示的版本号
为该整体机的固件版本号。
V 0.05
4. 光效设置
FX/
FX
/
20 20
20 20
闪光灯光效模式 雷闪电光效模式
坏灯泡光效模式 电视机光效模式
5. 连接线没有连接好
6.AC供电切换V口电池供电
当AC供电切换V口电池时，建议先拔掉电源线，再插入V口电池开机使用。
13 14

提示：未拔电源线插入V口电池，且灯体设置亮度值高于电池能开的最大亮
度值，试图用拔掉电源线的方式切换成V口电池供电，灯体及控制器会自动
关闭，重新开机后即可正常使用。
不同状态下UL150II最大亮度值
CCT模式： 灯最大亮度值(％)
供电方式
14.8V(单个)
14.8V(双个)
26V(单个)
14.8V+26V
26V(双个)
线性
50％
100％
100％
100％
100％
100％
S型
50％
100％
100％
100％
100％
100％
指数
50％
100％
100％
100％
100％
100％
对数
50％
100％
100％
100％
100％
100％
软件升级
1.在官网http://www.godox.com.cn/Downloads.html下载新固件到U盘上。
2.在关机的状态下,将已经存有新固件的U盘插入USB升级接口。
2.开机，摄影灯自动进入升级界面。
3.升级完后自动跳回主界面。
注:1.必须在官网上下载新固件，存放在U盘根目录里，而且仅有一个BIN文件。
2.USB口仅用于升级固件功能。
维护保养
—年保修期，消耗品电池，适配器，电源线等配件不在此保修范围内。经发现，
擅自检修此LED灯，将取消LED灯一年保修期，维修需要收取相关费用。
对于不规范操作引起的机器故障不在保修范围内。
所有维修概由本厂指定的可供原配件的维修部负责。
如果本品出现故障或者被水淋湿，在专业人员维修后方可继续使用。
摄影灯在工作时，如发现异常，应立即关掉电源，查明原因。
色温数值
CRI
TLCI
工作环境温度
FX情景光效
控制方式
调光模式
静音模式
蓝牙传输距离
2.4G无线控制距离
5600K
≥96
≥97
-20~40℃
4类12种
支持DMX512控制、2.4G无线遥控、蓝牙控制、控制盒控制
4种：线性/S型/指数/对数
具备
≈30m
≈60m
规格参数
型号
功率
AC供电输入
DC供电输入
灯头输入
V口电池（另购）规格参数
频道
组别
识别号（ID号)
UL150II
最大160W
100-240V ~50/60Hz
DC 48V
65V2.3A
14.8V，150Wh/26V，270Wh
32个（1~32）
16组（0~9、A~F）
1~99 、OFF
AC电源/48V直流电源
FX模式： 灯的最大亮度值(％)
供电方式
14.8V(单个)
14.8V(双个)
26V(单个)
14.8V+26V
26V(双个)
线性
50％
100％
100％
100％
100％
100％
AC电源/48V直流电源
注：使用FX情景光效时，调光曲线不起作用，默认为线性。上述数据基于26V 270Wh
10.5Ah电池和14.8V150Wh 10.2最大Ah电池。
15 16

灯体尺寸
控制器尺寸
灯体重量
控制器重量
316.9*217.8*170mm
270.4*123.6*132mm
≈3.11kg
≈2.66kg
设计和规格如有变更，恕不另行通知。
照度数据
测试条件
1m 2m 3m
色温
5600K
5600K
裸灯
带标准罩
注：上述测试皆在灯体100％亮度下进行。
17 18
lux
fc
lux
fc
5700
530
71700
6660
1600
150
16000
1500
790
73
6000
560
本设备包含型号核准代码为:CMIITID:2020DP13510，为该产品的无线电发射模块。
照度单位
1.Before use, please read and understand these instructions and attentions.
2.Professional lighting is prohibited for children. When children are near, parents or
accompanying persons must supervise closely to prevent children from personal injury
due to collision with lamps or private use of lamps.
3.This lighting product is not ordinary lighting product and cannot be used for general
lighting. Anyone who has suffered eye damage or has sensitive eyes should avoid using
this product.
4.When the lamp is on, it must be used with care. Do not touch high-temperature parts,
such as LED lamp beads, to avoid burns.
5.When the lamp is on, it is forbidden to look directly at the lamp beads under any
circumstances. Strong light should be used under the guidance of professional lighting
engineers. Avoid prolonged exposure to strong light under any circumstances. If eye
discomfort, please turn off the lamp in time, suspend use, and see a doctor immediately.
6.If the lamp bead is damaged or deformed by heat, stop using this equipment, and
contact the manufacturer, service agent or qualified maintenance personnel to replace
the lamp bead in time to avoid accidents.
7.This product is only suitable for use in -20to 40operating environment and
normal humidity environment.
8.Do not use damaged equipment or accessories, and wait for professional maintenance
personnel to check and repair to confirm being normal before use.
9.During using, if the casing of this product is broken due to being dropped, squeezed or
subjected to strong impact, please do not use it, so as to avoid electric shock injury due
to contact with internal electronic components.
10.If an extension cord is required, please use an extension cord with a current rating
greater than or equal to that of the equipment. If an extension cord is rated less than the
equipment, overheating may result.
11.Some products have long power cords, please place the power cords properly and
keep them in a safe place. Avoid contacting the power cord with overheating surfaces,
avoid improper placement that could cause pulling damage, or trip on-site personnel.
Please use the certified power cord from the original manufacturer. If the product is
damaged by using a non-certified power cord, it will not be repaired by our factory.
12.Be sure to unplug equipment from the power outlet before cleaning and repairing.
When not in use, do not pull the power cord to unplug the equipment. For normal
power-off, please hold both ends of the plug of the equipment with your hands and pull
the plug out of power outlet. This equipment needs to be connected to a grounded outlet.
13.This equipment is not waterproof, please keep it dry and do not immerse it in water or
Safety Instructions and Attentions
First of all, as the most basic principle: This product is a professional lighting
set equipment and should be used by professional lighting engineers or under
the guidance of professionals. Basic safety attentions must always be followed
during use, as follows:

Foreword
Thank you for purchasing!
Silent LED Video Light UL150II is fanless design and noise-free. The separate light body
and controller are conveniently operational. Stable light source creates high CRI and
great performance. It supports Bluetooth APP wireless group control and stepless
brightness adjustment. This product is suitable for various shooting scenes such as live
streaming, video recording, interview and etc.
Main Features
Fanless and noise-free, stable full power output.
Strong power and stable light source, support stepless brightness adjustment.
V-mount battery supply or AC power supply, available both indoors and outdoors.
Separated design of light body and controller achieves convenient operation and better
cooling effect.
Support 2.4G remote control/Bluetooth APP control/DMX512 control.
U-bracket to support various angle usage.
12 simulated light effects bring rich lighting creations.
Standard Bowens mount is compatible with most optical accessories.
Warning
Keep out of reach of children.
Please take off the lamp cover before using.
Always keep this product dry. Do not use in rain or in damp conditions.
Do not disassemble. Should repairs become necessary, this product must be
sent to an authorized maintenance center.
As this product do not have waterproof function, please take measures of
waterproof in rainy or damp environment.
Do not fire directly against human eyes as it may cause visual impairment.
Do not leave or store the product if the ambient temperature reads over 40°C.
Please use the original power cable, damages caused by using other cables will
invalid the warranty.
Do not use the product in the presence of flammable gases, chemicals and
other similar materials.
The light source contained in this luminaire shall only be replaced by the
manufacturer or his service agent or a similar qualified person.
The lamp shall be changed if it has become damaged or thermally deformed
The luminaire is intended for professional use only.
19 20
Do not stare at the operating light source.
other liquids. The equipment should be installed in a dry and ventilated place, and avoid
using it in rainy, humid, dusty or overheated environments. Do not place any objects on
the lamp or let liquid flow into the lamp to avoid accidents.
14.Do not disassemble the product without permission. If the product fails, it must be
checked and repaired by authorized maintenance personnel.
15.Before storing, make sure that the equipment has cooled down completely. For
storage, unplug the power cord from the equipment. The equipment should be placed in
the carrying case or in a ventilated dry place.
16.Do not place equipment near flammable and volatile solvents such as alcohol and
gasoline.
17.Do not use accessories that are not recommended by our factory to avoid fire, electric
shock or personal injury.
18.When cleaning, do not wipe it with a damp cloth, please use a dry cloth or a soft cloth
to wipe the dirt of the equipment.
19.Please take off the protective cover before using.
20.This product complies with ROHSCEand FCC certification, please refer to the
relevant national standards for use and operation.
21.The safety instructions are formulated according to the strict testing of the factory,
and the design and specifications of the equipment are subject to change without prior
notice. For latest product information, please check the GODOX website and view latest
electronic instruction.
22.Some products have built-in lithium batteries. Please use specified chargers, and use
them within a proper range of the specified voltage and temperature according to the
correct operating instructions.
23.Some products are battery powered. Do not use any batteries, power sources or
accessories not specified in the instructions for such products. Keep batteries and other
accessories out of the reach of children and infants. In the instance that a child or infant
swallows a battery or accessory, immediate emergency medical attention is required. If
the battery leaks, becomes discolored, deformed, emits smoke, or emits an abnormal
odor, remove it immediately. Be careful during removal to avoid burns. Continued use
could result in fire, electric shock, or burns. Do not use any deformed or modified batter-
ies. Do not disassemble or modify this product or battery. Do not heat or solder the
battery. Keep the battery away from fire or water. Do not incorrectly insert the positive
and negative ends of batteries, or mix old and new batteries or batteries of different types
together.
24.One-year warranty period, accessories such as consumable batteries, adapters,
power cords, etc. are not covered by this warranty.
25.If it is found that the equipment is repaired without authorization, the one-year
warranty period will be cancelled and relevant fees will be charged for maintenance.
26.Machine failures caused by non-standard operation are not covered by the warranty.
keep these instructions!

Separately Sold Accessories
Remote Control RC-A6 Safety Wire Rope
Controller
1. Light Body
2. Ventilation Hole
3.Bowens Mount
4.Protection Cover
5.LED Bead
6.Umbrella Input
7.Umbrella Fixing Knob
8.U-bracket
9.Bracket Fixing Knob
10.Bracket Sleeve
11.Handle
12.DC Input Port
13.Mount Fixing Pusher
What’s in the Box
Name of Parts
Light Body
1.USB Type-A Port
2.SET Adjustment Dial
3.Power Switch Button
4.MENU Button
5. /FX Button
6.DMX Setting Button
7.Black Battery Removal
Button
8.V-mount Battery Box
9.AC INPUT Port
10.DC 48V Port
11.Yellow Battery Removal Button
12.DMX IN XLR Port
13.DMX OUT XLR Port
Light Body*1 5m Power Cable*1Connecting Cable*1 Controller Clamp*1 Lamp Cover*1
Connecting Cable
Fixed Rope*1
Controller
*1
Bowens-mount
Reflector RFT-19*1
Instruction
Manual*1
Fresnel Attachment
for COB LED lights
SpotLight Attachment
21 22
⑦
①
②
⑪
⑨
⑨
⑨
⑧
⑧
⑬
③
⑤
⑫
⑦
⑥
④
⑩
⑩⑫
⑬
⑪
①
②
③
④
⑤
⑥

DMX512
2. Mount on the tripod
Adjust the light body to a proper angle,
rotate the screw of sleeve knob to
install the light body on the tripod, then
rotate the screw of sleeve knob to fix
the light body on the tripod. The inclina-
tion angle of the light body could be
adjusted by loosening the bracket angle
adjustment handle and then screwing
down the handle afterwards.
Note: The tripod belongs to separately
sold accessories.
3. Mount on the light stand
Loosen the handle of the controller
clamp, then insert the light stand and
rotate the handle to tighten. Finally,
insert the V port of the controller into
the clamp slot.
Tip: Press and hold the mount fixing
pusher can easily remove the controller.
4.Installation and disassembly the
protection cover
Installation: Press the Mount Fixing
pusher top-down, put the protection
cover on Bowens Mount, and rotate
clockwise to tighten it.
Disassembly: Press the Mount Fixing
pusher top-down, then rotate counter-
clockwise to remove it.
Note: Make sure to remove the protec-
tion cover before use to avoid overheat-
ing damage. Put on the protection cover
to protect the lamp when not in use.
5. Installation and disassembly the
standard reflector
Installation: Press the Mount Fixing
pusher top-down, put the reflector on
Bowens Mount, and rotate clockwise to
tighten it.
Disassembly: Press the Mount Fixing
pusher top-down, then rotate counter-
clockwise to remove it.
Installation and Disassembly Guide
1. Connect the controller and the light body
Press and hold the spring latch button of the connecting cable, insert the connecting
cable into the DC INTPUT Port of the light body, then insert the other end of the
connecting cable into the DC OUTPUT Port of the controller to complete the connec-
tion.
Connect to DMX Controller
The connecting operation diagram of Controller ULC150II and DMX Controller is as
follows:
Multi-connected
23 24

Controller ULC150II Operation Instruction
2. Brightness Adjustment
Turn the SET adjustment dial on the main
interface to adjust brightness from 0% to
100%. Rotate clockwise to increase
brightness, and counterclockwise to
decrease brightness. The brightness will
increase or decrease by 1 unit in normal
rotation speed; and increase or decrease
by 10 unit in rapid rotation speed.
Note: Short press the SET adjustment
dial once on the main interface to turn off
the light, press again to turn on and
display the previous brightness.
Display Screen
2. V-mount battery power supply
Power Supply
1.AC Power Supply
AC100V-240V
Note: Please press the latch button when installing or disassembling the
power cable and connecting cable.
spring latch
Note: The light can be supplied by 14.8V or 26V V-mount battery. Only the side with
yellow battery removal button supports unilateral power supply. When it is powered by
two batteries and one of which is low, the device still can't work normally even if the
other one is full. The corresponding battery icon will blink in low battery mode. It is
recommended to check whether both batteries have sufficient power when using two
batteries.
1. Turn On/Off
Press the controller Power Switch
Button for 1 second after connecting to
the power supply to turn on or off.
Lock Function Indication
Brightness Value
Bluetooth
2.4G Wireless GroupChannel
Dimming Curve
Battery Level
Indication
Battery Level
Indication
Overheating
Alert
25 26

3.3 DMX
The DMX interface is displayed with
Address. Turn the SET adjustment dial to
choose address from OFF or 1-512, the
light will be in DMX OFF or ON mode
respectively. Afterwards, short press the
SET adjustment dial to return to the
previous menu interface.
3. Menu Setting
Short press < MENU > Button to enter the menu interface, displayed in order with
Wireless, Bluetooth, DMX,Dimmer, Screen Bright, Language, Reset, Version &
Upgrade.Turn and short press the SET adjustment dial on the menu interface to select
and enter the corresponding setting options interface.
3.1 Wireless
The Wireless interface is displayed in order
with Wireless Switch, Channel, Group and
ID. Short press & turn the SET adjustment
dial to complete the settings of Wireless
Switch, Channel, Group and ID.
3.2 Bluetooth
The Bluetooth interface is displayed in
order with Bluetooth Switch, Reset and
MAC Code.
Short press & turn the SET adjustment dial
to complete the settings of Bluetooth
Switch and Bluetooth Reset.
3.4 Dimmer
Turn the SET adjustment dial on the
Dimmer interface to choose
linear/S-curve/exponential/logarithmic
dimming curve.
3.5 Screen Bright
Turn the SET adjustment dial on the
screen bright setting interface to
choose 1, 2, 3 levels of screen
brightness.
For more smartphone APP operations, please open the
"help" in “GodoxLight” APP to gain detailed guidance
(both Android and IOS systems are available).
Note: the APP can be used directly on the firstly installed device
(smartphone or tablet). When changing to other mobile device,
the light shall be reset before the normal usage of APP.
DMX Practical Form
Address
Code
Operation
Mode
CCT FX
n(Mode）0-51 52-255
n+1
DMX*(100/255) Integer
0-100% brightness
adjustment
DMX*(100/255) Integer
0-100% brightness
adjustment
n+2
DMX*
(Total Light Effect/255)
1. For Example: Total Light
Effect 8,DMX=160, Light
Effect NO.=160*8/255=5
n+3
n+4
n+5
0-85: Light Effect Level I
86-171: Light Effect Level II
172-255: Light Effect Level III
WIRELESS
BLUETOOTH
RESET
MAC: F463
ADDRESS: OFF
Dimmer
27 28
Note

4. Light Effect Setting
Short press < > button to enter FX light effect interface, turn the SET adjustment
dial to choose flash, lightning, broken bulb or TV scenes.
3.8 Version & Upgrade
The Version Code displayed on the
Version & Upgrade interface is the
firmware version of the product.
5. Connecting Cable Issue
When the connecting cable is not
correctly connected to the light or
controller, a separated icon of connect-
ing cable and device is displayed on the
panel. Please check the connecting
ports of the controller and light.
FX/
3.6 Language
Turn the SET adjustment dial on the
Language interface to choose English or
Simplified Chinese.
3.7 Reset
Turn the SET adjustment dial on the Reset
interface to choose “Yes” or “No” and short
press to confirm. If you choose “Yes”, the
system will initiate resetting program and
resetting progress bar is displayed on the
screen, after which it will return to the main
interface.
Note: The brightness will change to 100 
after resetting.
FX/
Note: Short press the SET adjustment dial to change the rate (IIIIII) and adjust
brightness (0-100) after choosing one of the above Light Effects.
Tips: Long press the < > button to lock/unlock the screen.
V 0.05
Version&Upgrade
Poweroff andinsert
USBdisk with newfirmware
Restarttoupgrade
ENGLISH
NO
YES
Flash Mode Lightning Mode
TV ModeBroken Bulb Mode
20 20
20 20
Dim Dim
DimDim
29 30

6. Switch from AC Power Supply to V-mount Battery
Power Supply
Unplug the power cable and install V-mount battery then turn on the
product.
NoteIf you install the V-mount battery before unplugging the power cableand the
brightness value is set higher than the maximum brightness that the battery can be
turned onthen you switch to V-mount battery power supply by unplugging the power
cable, the light and the controller will automatically power off. The machine can only
resume normal operation after reboot.
Maximum Brightness in Different States
CT modeMaximum Brightness (%)
linear
50％
100％
100％
100％
100％
S-curve
50％
100％
100％
100％
100％
exponential
50％
100％
100％
100％
100％
logarithmic
50％
100％
100％
100％
100％
FX mode: Maximum Brightness (%)
Power Supply
14.8V(single)
14.8V(double)
26V(single)
14.8V+26V
26V(double)
linear
50％
100％
100％
100％
100％
100％
AC Power Supply/48V DC Power Supply
Power Supply
14.8V(single)
14.8V(double)
26V(single)
14.8V+26V
26V(double)
AC Power Supply/48V
DC Power Supply 100％ 100％ 100％ 100％
Note: The dimming curve is not adjustable in FX mode, it is linear in default. The above
data is based on 26V 270Wh 10.5Ah battery and 14.8V 150Wh 10.2 Ah battery.
Software Upgrade
1.Download the new firmware to the U disk from the official website (http://www.go-
dox.com.cn/Downloads.html).
2. Turn off the device. Insert the U disk with new firmware into the USB upgrade port.
3. Turn on the device, and it will automatically enter the upgrading interface.
4.It will return to main interface after completion.
Notes:
1. New firmware must be downloaded from the official website, and keep only one BIN
file in the root directory of the USB disk.
2. The USB port can only support firmware upgrade function.
Maintenance
This product, except consumables e.g. adapter and power cable, is supported with a
one-year warranty.
Maintenance of the light must be performed by our authorized maintenance depart-
ment which can provide original accessories.
Unauthorized service will void the warranty.
If the product breaks down or gets wet, please do not use it until repaired by profession-
als.
If there is anything abnormal during LED light’ s working, please turn it off imme-
diately and identify the reasons.
Declaration of Conformity
GODOX Photo Equipment Co,Ltd. hereby declares that the This equipment are in
compliance with the essential requirements and other relevant provisions of EU
Directive 2014/53/EU. They are allowed to be used in all EU member states.
For more information of DoC, Please click this web link:http://www.godox.com/
DOC/Godox_UL150II_DOC.pdf.
31 32

Technical Data
Mode
Power
AC Power Input
DC Power Input
Light Head Input
V-mount Battery (optional)
Specifications
Channel
Group
ID
Color Temperature
CRI
TLCI
Working Environment Temperature
FX Light Effect
Controlling Method
Dimming Curve
Mute Mode
Bluetooth Transmission Distance
2.4G Wireless Control Distance
Light Body Dimension
Controller Dimension
Light Body Weight
Controller Weight
Bluetooth Transmission Frequency
Maximum Transmit Power
2.4G Frequency Range
UL150II
Max.160W
AC100-240V ~50/60Hz
DC 48V
65V2.3A
14.8V150Wh/26V270Wh
1~32
16 groups0~9A~F
1~99 OFF
5600K
≥96
≥97
-20~40
12 kinds within 4 types
Support DMX512, 2.4G Wireless
Control, Bluetooth Control, Controller
4 types: linear/S-curve/exponential/
logarithmic
YES
≈30m
≈60m
316.9*217.8*170mm
270.4*123.6*132mm
≈3.11kg
≈2.66kg
2402MHz-2480.0MHz
5dbm
2412MHz-2464.5MHz
Product design and specifications are subject to change without notice.
Illuminance Testing Data
Testing Condition
1m
790
73
6000
560
1m
5700
530
71700
6660
2m
1600
150
16000
1500
CCT
5600K
5600K
Bare Lamp
Lamp with Cover
FCC Statement
This device complies with part 15 of the FCC Rules. Operation is subject to the
following
two conditions: (1) This device may not cause harmful interference, and (2) this device
must accept any interference received, including interference that may cause
undesired
operation.
Any Changes or modifications not expressly approved by the party responsible for
compliance could void the user's authority to operate the equipment.
Note: This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential installation.
This equipment generates uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following
measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
The device has been evaluated to meet general RF exposure requirement.
The device can be used in portable exposure condition without restriction.
Note: The above tests are all based on the condition of 100% brightness.
33 34
lux
fc
lux
fc
Illuminance Unit

本文件适用于相关《产品保修信息》(见后面说明)所列产品，其他非属此范围的产品或部
件(如促销品、赠品及其他出厂后附加的部件等)不在此保修承诺内。
您可直接与产品销售商或授权服务机构联系，也可拨打神牛产品售后服务电话，与我们
联系，由我们的服务人员为您安排服务。申请保修时，您应提供有效的保修卡作为保修凭
证，方可获得保修。如您不能提供有效的保修卡，则在我们确认产品或部件属于保修范围
的情况下，也可以为您提供保修， 但这不作为我们的义务。
如产品存在下列情况，本文件项下的保证和服务将不适用 ①产品或部件超过相应保修期
；②错误或不适当使用、维护或 保管导致的故障或损坏，如：不当搬运；非按产品合理预期
用途使用；不当插拨外接设备；跌落或外力挤压；接触或暴露于不适当温度、溶剂、酸碱、
水浸或潮湿环境；③由非神牛授权机构或人员安装、修理、更改、添加或拆卸造成的故障
或损坏；④产品或部件原有识别信息被修改变更或除去；⑤无有效保修卡；⑥使用非合法
授权、非标准或非公开发行的软件造成的故障或损坏；⑦因不可抗力或意外事件造成的
故障或损坏；⑧其他非因产品本身质量问题导致的故障或损坏。遇上述情况，您应向相关
责任方寻求解决，神牛对此不承担任何责任。因非在保修期或保修范围内的部件、附件或
软件导致产品不能正常使用的，不是保修范围内的故障。产品使用过程中正常的脱色，磨
损和消耗，不是保修范围内的故障。
产品及部件的相应保修期按相关的《产品保修信息》执行。保修期自产品首次购买日起算，
购买日以购买产品时保修卡登记日期为准。
产品保修
尊敬的用户，本保修卡是申请保修服务的重要凭证，请您配合销售商填写并妥善保管，谢
谢！
用户信息 姓名 联系电话
通信地址
产品信息 型号 产品条码
销售商
信息
名称
联系电话
通信地址
销售日期
备注
注：此表应由销售商盖章确认。
适用产品
如何获得保修服务
不适用保修的情况
产品保修和服务支持信息
产品的保修期和服务类型按以下《产品保修信息》执行：
产品类别
部件
其他
选件名称
电路板
电池
如闪光管、造型灯泡、外壳、
保护罩、锁紧装置、包装等。
保修期
保修服务类型
客户送修
客户送修
客户送修
无保修
保修期 月( )
12
3
12
无
神牛产品售后服务电话：[phone]-8062
充电器、电源线，同步线等
带电性能的部件。
33 34

If maintenance service is needed, you can directly contact the product distributor or
authorized service institutions. You can also contact the Godox after-sale service call
and we will offer you service. When applying for maintenance service, you should
provide valid warranty card. If you cannot provide valid warranty card, we may offer
you maintenance service once confirmed that the product or accessory is involved in
the maintenance scope, but that shall not be considered as our obligation.
Warranty
The document applies to the products listed on the Product Maintenance lnformation
(see below for further information). Other products or accessories (e.g. promotional
items, giveaways and additional accessories attached, etc.) are not included in this
warranty scope.
The warranty period of products and accessories is implemented according to the
relevant Product Maintenance lnformation. The warranty period is calculated from the
day(purchase date) when the product is bought for the first time, And the purchase
date is considered as the date registered on the warranty card when buying the
product.
Dear customers, as this warranty card is an important certificate to apply for our
maintenance service, please fill in the following form in coordination with the seller and
safe-keep it. Thank you!
Customer
Information
Name
Address
Product
Information
Model Product Code Number
Contact Number
Seller
Information
Name
Contact Number
Address
Note:
Note: This form shall be sealed by the seller.
Applicable Products
Date of Sale
How to Get the Maintenance Service
The guarantee and service offered by this document are not applicable in the following
cases: . The product or accessory has expired its warranty period; . Breakage or
damage caused by inappropriate usage, maintenance or preservation, such as
improper packing, improper usage, improper plugging in/out external equipment,
falling off or squeezing by external force, contacting or exposing to the improper
temperature, solvent, acid, base, flooding and damp environments, etc; . Breakage or
damage caused by non-authorized institution or staff in the process of installation,
maintenance, alternation, addition and detachment; . The original identifying
information of product or accessory is modified, alternated, or removed; . No valid
warranty card; . Breakage or damage caused by using illegally authorized, nonstan-
dard or non-public released software; . Breakage or damage caused by force
majeure or accident; . Breakage or damage that could not be attributed to the
product itself. Once met these situations above, you should seek solutions from the
related responsible parties and Godox assumes no responsibility. The damage caused
by parts, accessories and software that beyond the warranty period or scope is not
included in our maintenance scope. The normal discoloration, abrasion and consump-
tion are not the breakage within the maintenance scope.
Inapplicable Cases
Warranty Period
33 34
Product Type
Parts
Other Items
Name
Circuit Board
Battery
Flash tube, modeling lamp, lamp
body, lamp cover, locking device,
package, etc.
Warranty Service Type
Customer sends the product
to designated site
Customer sends the product
to designated site
Customer sends the product
to designated site
Electrical parts e.g.battery charger,
power cord, sync cable, etc.
The warranty period and service types of products are implemented according to the
following Product Maintenance Information:
Maintenance
Period(month)
12
3
12
NO Without warranty
Godox After-sale Service Call 0755-29609320-8062
Maintenance and Service Support Information