Goldmedal 2626 User manual

Part No. 17027
Revised: February 2010
KARMEL BABY CORN TREAT
Instruction Manual
Model #2626

SAFETY PRECAUTIONS

KARMEL BABY
MODEL# 26263
INSTALLATION INSTRUCTIONS
Inspection of Shipment:
Unpack all cartons and check thoroughly for any damage that may have occurred during
transit. Damage claims should be filed immediately with the transportation company. Gold
Medal Products is not responsible for damage that occurs in transit.
Setup:
Your new KARMEL BABY is completely assembled and tested at the factory.
Remove all packing material and tape before starting operation.
Electrical Requirements:
Voltage for the 2626 is 120 volt, 60 cycle single phase. The machine will draw a maximum of
15amps. Your electrician must finish sufficient current for the proper operation of your machine. We
recommend this machine be on a dedicated and protected circuit line.
The 2626 has a current draw of 15 amps
Your electrician must furnish sufficient power for proper machine operation. We recommend
this popper be on a dedicated and protected circuit. Failure to wire properly will void the
warranty and may result in damage to the machine.
It is Gold Medal Products Company’s recommendation that this machine be plugged directly
into a wall outlet. The use of extension cords is not recommended due to safety concerns,
and may cause sacrificed and/or reduced performance.

KARMEL BABY
MODEL# 26264
CONTROLS AND THEIR FUNCTION
HEAT and MOTOR SWITCH
This rocker switch in the “ON” position energizes the heating elements in the bottom of the kettle.
I = ON and O = OFF
MOTOR SWITCH
With this rocker switch in the “ON” position, the agitator motor will run continuously.
HEAT CONTROL
The machine comes from the factory preset at 280°F for Corn Treat Centers. If more or less heat is
required, remove the silver hole plug or cover plate located on the front panel of the control box. This will
allow you to access the heat control adjustment potentiometer. Turn the potentiometer clockwise to
increase the temperature.
To calibrate the heat control for corn treat, Fill the mixing bowl with enough corn oil to cover the heat
sensor (around 1-1/2”) . Use an accurate thermometer to measure the temperature of the oil in the mixing
bowl. Stir the oil while it heats. When the oil reaches 310F slowly turn the potentiometer counter clockwise
until the buzzer sounds. If the buzzer sounds before the temperature reaches 310F turn the potentiometer
clockwise until the buzzer stops and continue to turn an additional 1/8 of turn.
Note: The sound of the buzzer always signals temperature cut-off.

KARMEL BABY
MODEL# 26265
INSTRUCTIONS FOR MAKING CARAMEL CORN
1. Turn the motor / heat switch "ON".
2. Add 4 ounces of water, one package of Gold Medal 2157 2.5 gal caramel complete mix.
3. Turn the motor switch "ON" and mix for approximately one minute. Turn the motor switch "OFF". (With
the heat switch "ON" the motor will run for 15 seconds every minute.)
4. Allow the mix to cook until the buzzer sounds at 280° F product temperature.
5. Turn the motor / heat switch "OFF".
6. Turn the motor switch "ON".
7. Add two and a half gallons of pre popped corn.
8. Allow the corn to mix for approximately thirty (30) seconds with the kettle in the upright position.
9. Move the kettle to the mix position and mix the popcorn until it is thoroughly coated.
10. Dump the caramel corn into the cooling pan.
CARE AND CLEANING
STEAM CLEANING
The easiest way to clean the kettle is to pour 8 ounces of water into the kettle while it is still hot. Place the
lid back on the kettle. Let it steam for approximately ten minutes. Remove the lid and dump out the water.
You will probably have to steam the kettle twice to remove all traces of product. Releasing the draw latch
makes the mixing drum easy to remove for cleaning. The mixing drum can be taken to the sink to clean.
The cabinet of your machine should be wiped cleaned daily; or more, depending on your usage.

KARMEL BABY
MODEL# 26266
NEW PADDLE & HUB SEAL KIT INSTALLATION
1. Unscrew the wing bolts and remove both mix paddles.
2. Remove the old hub seal assembly.
3. Clean the area around the center hub. Clean up all food and carbon residue.
4. Remove any burrs on the top edge of the center hub. Use a fine grit emery paper to lightly sand the
surface. If the burrs are not removed, damage may occur to the hub assembly during installation.
5. Lightly lubricate the center hub of the kettle with a small amount of vegetable oil to allow for easy
installation of the hub seal assembly.
6. Slide the hub seal assembly down the agitator shaft. Apply pressure to ease the assembly over the
center hub of the kettle until it seats properly. (See diagram below.)
7. After the hub seal assembly has been properly installed, place the new mix paddle on the bottom and
one existing paddle on the top of the agitator shaft.
8. Replace the wing bolts and finger tighten.

KARMEL BABY
MODEL# 26267

KARMEL BABY
MODEL# 26268
ORDERING SPARE PARTS
1. Identify the needed part by checking it against the photos, illustrations, and/or the parts list.
2. When ordering, please include part number, part name, and quantity needed.
3. Please include your model name, serial number, and date of manufacture (located on the machine
nameplate) with your order.
4. Address all parts orders to:
Parts Department
Gold Medal Products Co.
10700 Medallion Drive
Cincinnati, Ohio 45241-4807
[phone]
[phone]
Fax: [phone]
or, place orders at:
E-mail: [email protected]
Web Page: www.gmpopcorn.com

KARMEL BABY
MODEL# 26269
Assembly Parts
Drive Shaft
p/n 16732
Mix Paddles
p/n 16737
Kettle Casting
p/n 16766
Mixing Drum
p/n 16761
Blending Strip
p/n 16765
RTD Senso
r
p/n 46299
Hub Seal Assy (Includes O-Ring)
p/n 16752
Lid Assembly
p/n 16810
Internal Kettle Parts (Not Shown)
1720W Element – p/n 67889
525F Thermostat – p/n 76702
Kettle Drive Shaft O-ring – p/n 16747
Mix Paddle Lock Stud (2)
p/n 16761

KARMEL BABY
MODEL# 262610
Assembly Parts (Con’t)
Retaining Ring And Seal
(See Zoomed View Below)
Dump Handle
p/n 41139
Handle
p/n 16985
Bottom Plate
p/n 16760
Motor Mount
p/n 16897
Moto
r
p/n 16723
Lead In Cord
p/n 87085
Drum Seal
p/n 16764
Motor Stop
p/n 16926
Retaining Ring
p/n 16762