Goldmedal 4180 User manual

Apple Hacker
Instruction Manual
Model #4180
PartNo.38341
RevisedJune 1996
Cincinnati, OH 45241-4807 USA
a

SAFETY PRECAUTIONS
a

Apple Hacker
ALL MODELS #4180
1
OPERATING INSTRUCTIONS
Your APPLE HACKER comes to you fully assembled. However, to assure the sanitary condition
of the machine, we recommend that it be cleaned (as outlined below) before it is used.
See assembly drawing on page 3 for Item numbers.
TO USE
1. Lift Push Block (Item 3) and place the apple on the Blade Assembly (Item 4).
2. Remove hands and fingers from the cutting area and with a strong push or a quick thrust
bring the Push Block down to force the apple through the Blades.
TO CLEAN
1. Lift Push Block (Item 3) off Guide Rods (Item 2).
2. Remove screws (Item 9) from bottom of the Frame (Item 1) to release Blade Assembly
(Item 4).
3. Thoroughly wash the Push Block, Blade Assembly and the Frame in mild soapy water.
Rinse thoroughly.
4. Re-assemble by reversing the procedure.
TO LUBRICATE
When needed, lubricate the Guide Rods (Item 2) with mineral oil, food grade grease or rub
them with paraffin. Do NOT lubricate with cooking oil - it gets sticky!
a

Apple Hacker
ALLMODELS #4180
2
ORDERING SPARE PARTS
1.Identify the desired part by checking it against the photos, illustrations, and/or the parts list.
2.When ordering, please include part number, part name, and quantity desired.
3.Please include your model name and machine serial number (located on the machine
nameplate) with your order.
4.Address all parts orders to:
Parts Department
Gold Medal Products Co.
10700 Medallion Drive
Cincinnati, Ohio 45241-4807
or, place orders at:
[phone]
Fax: [phone]
E-mail: [email protected]
MAINTENANCE INSTRUCTIONS
THE FOLLOWING SECTIONS OF THIS MANUAL ARE IN-
TENDED ONLY FOR QUALIFIED SERVICE PERSONNEL.
THESE ARE NOT INTENDED FOR THE OPERATOR.
Adequate eye protection must be used when servicing this
equipment to prevent the possibility of injury.
a

Apple Hacker
ALL MODELS #4180
3
PARTS LIST – APPLE HACKER
Item No. Part No. Description Quantity
1 38333 Stand 1
2 38334 Guide Rod 2
3 38335 Push Block 1
4 38336 Blade Assembly 1
5 14843 Dowel Pin 2
6 49123 Crutch Tip 4
7 46028 Grip, Handle Bar 2
8 38338 “O” Ring 2
9* 40195 Machine Screw #6-32 x ¾" 2
10* 38337 Core Pin 1
11* 38323 Decal, Sharp Blades 1
Assembly (P/N-38339) includes the Stand with the Guide Rods pinned in place.
a

WARRANTY
WE WARRANT to the original purchaser the Gold Medal equipment sold by us to
be free from defects in material or workmanship under normal use and service. Our
obligation under this warranty shall be limited to the repair or replacement of any
defective part for a period of six (6) months from the date of sale to the Original
Purchaser with regard to labor and two (2) years with regard to parts and does not
cover damage to the equipment caused by accident, alteration, improper use, voltage,
abuse, or failure to follow instructions.
THIS WARRANTY IS IN LIEU OF ALL OTHER WARRANTIES EXPRESSED
OR IMPLIED, AND OF ALL OTHER OBLIGATIONS OR LIABILITIES ON OUR
PART, INCLUDING THE IMPLIED WARRANTY OF MERCHANTIBILITY.
THERE ARE NO WARRANTIES WHICH EXTEND BEYOND THE DESCRIPTION
ON THE FACE HEREOF. We neither assume, nor authorize any other person
to assume for us, any other obligation or liability in connection with the sale of said
GOLD MEDAL equipment or any part thereof.
The term “Original Purchaser” as used in this warranty shall be deemed to mean that
person, firm, association, or corporation who was billed by the GOLD MEDAL
PRODUCTS COMPANY, or their authorized distributor for the equipment.
THIS WARRANTY HAS NO EFFECT AND IS VOID UNLESS THE ORIGINAL
PURCHASER FIRST CALLS GOLD MEDAL PRODUCTS COMPANY AT 1-800-
543-0862 TO DISCUSS WITH OUR SERVICE REPRESENTATIVE THE
EQUIPMENT PROBLEM, AND, IF NECESSARY, FOR INSTRUCTIONS
CONCERNING THE REPAIR OR REPLACEMENT OF PARTS.
GOLD MEDAL PRODUCTS COMPANY
10700 Medallion Drive
Cincinnati, Ohio 45241-4807 USA
www.gmpopcorn.com
Phone: [phone]
Fax: [phone]
© The text, descriptions, graphics and other material in this publication are the proprietary
and exclusive property of Gold Medal Products Company and shall not be used, copied,
reproduced, reprinted or published in any fashion, including website display, without its
express written consent.