Goldmedal Econo-16 2024 User manual

Part No. 67833
Econo-16
Models 2024, 2024ST
16oz. Popcorn Machine
Instruction Manual
Cincinnati, OH 45241-4807 USA

16 oz. Econo-16
Models #2024, 2024ST
2
SAFETY PRECAUTIONS
DANGER
Machine must be properly grounded to prevent electrical shock to personnel.
Failure to do so could result in serious injury, or death.
DO NOT immerse any part of this equipment in water.
DO NOT use excessive water when cleaning.
Keep cord and plug off the ground and away from moisture.
Always unplug the equipment before cleaning or servicing.
Make sure all machine switches are in the OFF position before plugging the
equipment into the receptacle.
008_051514
DANGER
Improper installation, adjustment, alteration, service, or maintenance can
cause property damage, injury, or death. Any alterations to this equipment
will void the warranty and may cause a dangerous condition. This appliance
is not intended to be operated by means of an external timer or separate
remote-control system. NEVER make alterations to this equipment. Read the
Installation, Operating, and Maintenance Instructions thoroughly before
installing, servicing, or operating this equipment.
014_020416
WARNING
To avoid burns, DO NOT touch the kettle or any heated surface.
DO NOT place or leave objects in contact with heated surfaces.
013_092414
WARNING
ALWAYS wear safety glasses when servicing this equipment.
010_010914
WARNING
No user serviceable parts inside. Refer servicing to qualified service
personnel.
011_051514
WARNING
Read and understand operator’s manual and all other safety instructions
before using this equipment. To order copies of the operator’s manual go to
gmpopcorn.com or write to Gold Medal Products Co., 10700 Medallion Drive,
Cincinnati, OH 45241 USA 1-(800)-543-0862
022_060215

16 oz. Econo-16
Models #2024, 2024ST
3
SAFETY PRECAUTIONS (continued)
WARNING
DO NOT allow direct contact of this equipment by the public when used in
food service locations. Only personnel trained and experienced in the
equipment operation may operate this equipment.
Carefully read all instructions before operation.
012_010914
WARNING
This machine is NOT to be operated by minors.
007_010914
Note: Improvements are always being made to Gold Medal’s equipment. This information may
not be the latest available for your purposes. It is critical that you call Gold Medal’s Technical
Service Department at -800-543-0862 for any questions about your machine
operations, replacement parts, or any service questions. (Gold Medal Products Co. does
not assume any liability for injury due to careless handling and/or reckless operation of this
equipment.) General images may be used in manual for reference only.

16 oz. Econo-16
Models #2024, 2024ST
4
INSTALLATION INSTRUCTIONS
Inspection of Shipment
After unpacking, check thoroughly for any damage which may have occurred in transit. Claims should be
filed immediately with the transportation company. The warranty does not cover damage that occurs in
transit, or damage caused by abuse, or consequential damage due to the operation of this machine, since it
is beyond our control (reference warranty in back of manual).
Manual
Read and understand the operator’s manual and all other safety instructions before using this equipment.
To order copies of the operator’s manual go to gmpopcorn.com or write to Gold Medal Products Co., 10700
Medallion Drive, Cincinnati, OH 45241 USA 1-(800)-543-0862.
Model Description
Model 2024: 16 oz. Econo-16 Popper with LED cabinet lighting, and a red dome.
Model 2024ST: 16 oz. Econo-16 Popper with LED cabinet and sign lighting, and stainless steel dome.
Setup
This unit has been tested at the factory.
1. Remove all packaging and tape prior to operation.
2. Place the unit on a sturdy, level base.
3. The door knobs are shipped facing the inside of the machine. Re-adjust knobs to face the
outside of the machine.
4. After setup, unit should be cleaned prior to use (see Care and Cleaning section of this manual).
Electrical Requirements
The following power supply must be provided:
Model 2024 and 2024ST: 120 V~, 1900 W, 60 Hz
DANGER
Machine must be properly grounded to prevent electrical shock to personnel.
Failure to do so could result in serious injury, or death.
DO NOT immerse any part of this equipment in water.
DO NOT use excessive water when cleaning.
Keep cord and plug off the ground and away from moisture.
Always unplug the equipment before cleaning or servicing.
Make sure all machine switches are in the OFF position before plugging the
equipment into the receptacle.
008_051514
A certified electrician must furnish sufficient power for proper machine operation and install any supplied
receptacle. We recommend this equipment be on a dedicated and protected circuit. Failure to wire properly
will void the warranty and may result in damage to the machine. It is Gold Medal Products Co.’s
recommendation that this machine be plugged directly into a wall outlet. The use of extension cords is not
recommended due to safety concerns, and may cause sacrificed and/or reduced performance. Make sure
cord is located to prevent a trip hazard or unit upset.

16 oz. Econo-16
Models #2024, 2024ST
5
Before You Plug In Machine
1. Make sure all machine switches are OFF before plugging equipment into receptacle.
2. Make sure wall outlet can accept the grounded plugs (where applicable) on the power supply
cord.
3. The wall outlet must have the proper polarity. If in doubt, have a competent electrician inspect
the outlet and correct if necessary.
4. DO NOT use a grounded to un-grounded receptacle adapter (where applicable).
5. Install unit in a level position.
CAUTION
If the supply cord is damaged, it must be replaced by Gold Medal Products Co.,
its service agent or similarly qualified persons in order to avoid a hazard.
039_080614

16 oz. Econo-16
Models #2024, 2024ST
6
OPERATING INSTRUCTIONS
CONTROLS AND THEIR FUNCTIONS
LIGHT SWITCH
Operates cabinet lighting (and sign lighting for Model 2024ST).
WARMER SWITCH
Operates the heaters for the heated corn pan.
KETTLE HEAT SWITCH (and Indicator Light)
Operates the heating elements in the popping kettle. The Indicator Light will turn ON when the Kettle
Heat Switch is ON.
KETTLE MOTOR SWITCH
Operates the kettle agitator motor.
Popping Instructions
Amount of Popcorn and Oil – Salted Popcorn
The popper is equipped with a corn, salt, and oil measure. We recommend flavored and colored coconut oil.
Popcorn popped in coconut oil stays fresh longer and does not leave black deposits in the kettle like other
oils. Use only top quality, fresh popcorn from reputable suppliers.
Kettle Size
Popcorn Charge
Oil Charge
Flavacol (Salt)
16 oz. 16 oz. (473 ml) 5 oz. (148 ml) 1.5 Tblsp. (20cc)
For best results use Mega-Pop®16 oz. premeasured pouches (Item# 2846).
Popping Standard (Salted) Popcorn
1. Turn all switches ON.
2. To determine when kettle is ready to pop corn (about 4 minutes), test pop three kernels of corn
in one ounce (30 ml) of popping oil. When kernels pop, kettle is ready.
3. Lift kettle lid and load Mega-Pop®premeasured popcorn and oil pouch, or pour in popcorn and
Flavacol, then add oil in premeasured amount; close lid.
4. When corn has finished popping, gently dump the popcorn.
5. On final kettle of corn, turn Kettle Heat Switch OFF just as lids are forced open by the popping
corn. This procedure saves electricity, since kettle has plenty of heat, and helps eliminate
smoke/odor from any oil residue that remains after popping has stopped.
6. When finished popping, turn KETTLE HEAT and KETTLE MOTOR switches OFF.
NEVER LEAVE THE HEAT ON WHEN YOU ARE NOT POPPING CORN!

16 oz. Econo-16
Models #2024, 2024ST
7
Care and Cleaning
DANGER
Machine must be properly grounded to prevent electrical shock to personnel.
DO NOT immerse in water. DO NOT clean appliance with a water jet.
Always unplug the equipment before cleaning or servicing.
025_111616
WARNING
To avoid serious burns, DO NOT touch the kettle while it is hot!
028_082715
Good sanitation practice demands that all food preparation equipment be cleaned regularly (only use non-
toxic, food grade cleaners). A clean looking, well-kept machine is one of the best ways of advertising your
product.
Note: It is extremely important to follow all cleaning procedures, otherwise parts damage and
equipment failure will result. The warranty does not cover parts that are damaged due to
improper cleaning.
Daily Kettle Cleaning Instructions
CAUTION: A hot kettle will cause burns if you touch it with your hand. Allow kettle to cool at least 1
hour before attempting to clean. DO NOT use ice or water to cool down a hot kettle!
Severe kettle damage will result!
1. When cool, wipe outside of kettle with a clean, soft cloth. DO NOT use oven cleaners or abrasive
materials as they will damage the kettle.
2. Every night, mix Gold Medal’s Heat’n Kleen solution (Item No. 2095), 2 tablespoons per gallon of
water. It is not necessary to use the entire gallon at once; only use enough to fill the kettle 1/2
inch deep.
3. Turn kettle heat ON. When water starts to boil, turn kettle heat OFF.
4. Allow to cool at least 1 hour, then dump solution into a bucket and wipe inside of kettle with a
clean cloth. Make sure all solution goes into the bucket; do not spill any in the interior of
machine.
For an extra dirty kettle, the process may be repeated; or, after turning kettle heat OFF, allow
solution to sit in kettle overnight. The next morning, dump solution into a bucket and wipe inside
of kettle with a clean cloth.
5. With unit OFF and unplugged, wipe kettle lead cord with a clean SLIGHTLY damp cloth. DO NOT
get moisture into the kettle lead-in cord, severe damage will result.
Daily Unit Cleaning Instructions
1. Turn machine OFF, unplug unit and allow it to cool before attempting to clean.
2. Clean all pans/accessories in order to sanitize them before each use.
3. Take a clean, SLIGHTLY damp cloth and wipe excess grease from glass and cabinet.

16 oz. Econo-16
Models #2024, 2024ST
8
4. Wipe stainless steel parts with a clean cloth and cleaner designed for stainless steel, such as
Gold Medal Watchdog Stainless Cleaner (Item No. 2088).
DO NOT use oven cleaners or abrasive materials as they will damage parts of machine.
5. Clean glass panels with glass cleaner. Gold Medal Watchdog Glass Cleaner (Item No. 2588) is
recommended.
Ammonia cleaners will damage plastic doors/panels. Use only non-ammonia cleaners, such as
Gold Medal Watchdog Glass Cleaner (Item No. 2588).
6. The popcorn machine is equipped with an efficient and durable filtration system. The filter should
be cleaned every week to maintain maximum efficiency. Clean filter in warm soapy water, then
rinse and allow to dry overnight. Reinstall filter to its original position.

16 oz. Econo-16
Models #2024, 2024ST
9
Troubleshooting
Issue
Possible Cause
Solution
Power to the Unit
A. Power to the Unit A. Make sure the unit’s power cord is plugged
in.
Kettle Does Not Heat
A. Power to the Kettle A. Make sure kettle lead-in cord is plugged in
and twisted to lock into the kettle receptacle.
B. Kettle Heat Switch B. Have a qualified service person check the
voltage to and from the Kettle Heat Switch; if
switch is defective, replace it.
C. Heating Element C. Heating element in the kettle may be burned
out. Check with a qualified service person for
inspection/repair.
Long Popping Cycles
(Longer than 4 minutes for
Salt Popcorn)
A. Low Voltage A. If the machine is operated on low voltage,
this could cause the kettle not to reach the
proper operating temperature. Check with a
qualified electrician.
B. Inadequate Supply Lines B. Inadequately sized electrical supply lines or
use of extension cord, in addition to being a
fire hazard, would also prevent the kettle
from reaching the proper operating
temperature. Check with a qualified
electrician.
C. Inferior Corn C. Inferior quality corn would result in longer
popping cycles. Use only top quality hybrid
popcorn from reputable suppliers. Even
then, if you let your corn pick up moisture or
dry out, your popping cycles will be slow.
Kettle Agitator Shaft not
Rotating
A. Kettle Motor Switch A. If the kettle agitator shaft is not rotating,
DO NOT pop corn. Make sure the Kettle
Motor Switch is ON. If the switch is ON, and
the shaft is not rotating, the switch or motor
may be faulty, contact qualified service
personnel for inspection/repair.
B. Kettle Agitator Shaft/Stir
Blade not rotating. (Unit
must be OFF,
unplugged and cool
prior to checking or
adjusting the agitator
assembly.)
B. If the kettle agitator shaft is not rotating,
DO NOT pop corn.
•Kettles with a FIXED Stir Rod – check
the clearance between the shaft with
welded stir blade and the kettle bottom; it
should be a minimum of 1/32” (thickness of
a dime).
To make shaft adjustments, reference the
Agitator Set Collar Adjustment section.

16 oz. Econo-16
Models #2024, 2024ST
10
Agitator Set Collar Adjustment
The following instructions describe how to properly adjust set collars on an agitator assembly with a fixed
stir rod.
Agitator Assembly with a FIXED Stir Rod
Steps to Adjust Set Collars on Agitator with a Fixed Stir Rod
Agitator assembly is adjusted while fastened to the kettle (image shown for general reference only).
Step 1. Turn machine OFF, unplug unit, and allow it to cool completely before attempting to
adjust the agitator height.
Step 2. Loosen the set screw in the set collar above the crossbar and below the crossbar.
Step 3. Place a /32” gauge (thickness of a dime) under the base of the agitator shaft to adjust
clearance between the kettle cook surface and the shaft; reference image shown. Once adjusted,
re-tighten the set screw in the set collar above the crossbar to secure shaft in place.
Step 4. Adjust clearance between the bottom of
the crossbar and the lower set collar to /32”
(thickness of a dime); reference image shown.
Once adjusted, re-tighten set screw to secure in
place.
Step 5. To check for proper adjustment, make
sure the stir rod is parallel to the kettle cook
surface (it should be close - but not touching).
Step . Spin the agitator shaft by hand to ensure
it spins freely and is not dragging the bottom of
the kettle.
Agitator shown for general
image reference only (lids not
shown for clarity).
Step 4: Adjust clearance
to thickness of a dime.
Kettle Cook
Surface
Crossbar
Set Collar w/Set Screw
above Crossbar
Lower Set Collar
Agitator Shaft
Step
5: Adjust clearance to
thickness of a dime.
Stir Rod (welded to shaft)