Gotrax XR Ultra User manual

XR Ultra
ELECTRONIC SCOOTER
USER MANUAL

ALWAYS wear a helmet when riding your electric scooter.
Make sure your scooter has a full battery before taking it out to ride.
Always be aware of local road laws, and follow them.
Do not ride the scooter under the inuence of drugs or alcohol.
Always respect pedestrians.
Do not ride under wet conditions. The scooter may slide from under your
feet causing injury. Wet conditions may damage the electronics and void the
warranty.
Don’t Ride Until You Read This:

1. Avoid water - The scooter is not waterproof. The electronics may be damaged
due to water and water damage is not covered by our warranty. Riding in wet
conditions is also very dangerous and may result in injury.
2. Abuse - We do not cover physical damage due to negligent care and extreme
riding.
3. Whenever you ride the Gotrax Electric Scooter, you risk severe injury or even
death from loss of control, collisions, and falls. Use caution and ride at your own
risk.
4. Do not modify the product from the manufacturer’s original design; this will void
the warranty.
5. Keep hands and all body parts away from moving parts while operating the
scooter.
6. Before riding - be sure to check the scooter over and make sure the scooter is
operating correctly before each use.
7. Before riding - be sure to check that the braking system is functioning properly;
also be sure to check that all safety labels are in place and you understand the
safety warnings.
8. Before riding - be sure that any and all axle guards, chain guards, or other
covers or guards supplied by the manufacturer are in place and in serviceable
condition.
9. Before riding - be sure to check that the tires are in good condition, inated
properly, and have sucient tread remaining.
10.Never exceed the 220 lb (100 kg) maximum load rating.
11.The electric scooter should never be used by children under the age of 13.
12. Maximum Speed - Your electric scooter goes the maximum speed of 15.5 mph.
Warning Message

You should nd each of these items in your box:
1. Electric Scooter
2. Console & Handlebars
3. Approved Power Adapter / Charging Unit
4.Allen Wrench
5. Screws
6.Tire Gauge Pipe
7.Safety Pin
Remove all packaging material, then inspect each item for any
accidental damage that may have occurred during shipping.
Unpack
1
2
34 5
6
7
UNPACK
You should find each of these items in your G2 box:
1. G2 Scooter
2. G2 Console & Handlebars
3. Gotrax Approved Power Adapter / Charging Unit
4. Allen wrench
5. Screws
Remove all packing material, then inspect each item for any
accidental damage that may have occurred during shipping.
4
35

The electric scooter comes partially assembled.
Get To Know Your Scooter

Press down on the rear fender, separate the folding hook
and fender buckle, then lift the tiller upright (as shown in the
gure). Once the scooter is locked in the upright position,
verify by gently trying to fold.
Use an Allen wrench to loosen the screws located at the
hook and detach. Once you’ve removed the hook and
screws, make sure to remove the cover from the top of the
tiller.
Place the console into the top of the tiller.
Assemble Your Scooter
1
2
3

Take the cord that is attached to the hook and bring it to
the front of the tiller. Pull the handbrake towards you and
insert the round metal piece into the opening. String the
small silver cord through the solid piece of the handbrake.
Make sure the metal piece on the red cord is pushed fully
into the handbrake.
Grab the red cord and hook and bring it back behind the
tiller and reattach the hook to the back of the tiller using
the screws and an Allen wrench. (The red cord should go
around the tiller.)
5
4

Before using the scooter, you must fully charge the battery.
Charge Your Scooter

1. Open the rubber charging port cover.
2. Insert the charging plug into the port.
3. The charger box will have a green light when fully charged and a red light when
charging.
4. When you are done charging be sure cover the charging port to keep it clear of
dust and debris.
5. Charging Time: 4 hours
Charging Requirement: Make sure to charge your scooter in conditions that do not
exceed 104 degrees Fahrenheit or below 32 degrees Fahrenheit.

To power the scooter on, press and hold the red button for 1 second.
To power the scooter o, press and hold the red button for 5 seconds.
To power the headlight on or o, press the red button for 1 second while the
scooter is powered on.
To change between 1st and 2nd gear, press the red button for 2 seconds. The
display screen on the console will switch from the number 1 for 1st gear and number
2 for the 2nd gear.
The console on the scooter displays speed in MPH, Battery life, and what gear the
scooter is currently in.
Scooter Console Functions