Gotrax SHIFT S1 User manual

CONGRATULATIONS
ON YOUR PURCHASE!

This user manual will help you assemble and operate your new electric bike.
Be sure to read ALL OF THE INFORMATION in this manual before riding.
NOTE TO ALL RIDERS UNDER 18 YEARS OF AGE: It’s very important
that you get parental permission before riding your electric bike.

DON’T RIDE UNTIL YOU READ THIS:
ALWAYS wear a helmet when riding your electric bike.
Make sure your electric bike has a full battery before taking it out
to ride.
Always be aware of local road laws, and follow them.
Do not ride the electric bike under the inuence of drugs or alcohol.
Always respect pedestrians.
Do not ride under wet conditions. The electric bike may slide from
under your feet causing injury. Wet conditions may damage the
electronics and void the warranty.

1. Avoid water - The electric bike is not waterproof. The electronics may be
damaged due to water and water damage is not covered by our warranty. Riding
in wet conditions is also very dangerous and may result in injury.
2. Abuse - We do not cover physical damage due to negligent care and extreme
riding.
3. Whenever you ride the GOTRAX Electric Bike, you risk severe injury or
even death from loss of control, collisions, and falls. Use caution and ride at your
own risk.
4. Do not modify the product from the manufacturers original design.
5. Keep hands and all body parts away from moving parts while operating the
electric bike.
6. Before riding - be sure to check the electric bike over and make sure the electric
bike is operating correctly before each use.
7. Before riding - be sure to check that the braking system is functioning properly;
also be sure to check that all safety labels are in place and you understand the
safety warnings.
8. Before riding - be sure that any and all axle guards, chain guards, or other
covers or guards supplied by the manufacturer are in place and in serviceable
condition.
9. Before riding - be sure to check that the tires are in good condition, inated
properly, and have sufcient tread remaining.
10. Never exceed the 264 lb (120 kg) maximum load rating.
11. The electric bike should never be used by children under the age of 16.
12. Maximum Speed - Your electric bike goes the maximum speed of 20 mph.
WARNING MESSAGE

UNPACK
You should find each of these items in your S1 E-Bike box :
1. S1 E-Bike
2. S1 Approved Power Adapter / Charging Unit
3. 1- 5mm Allen Wrench
4. 1- 6mm Allen Wrench
5. S1 Battery
6. 2 - Pedals
Remove all packing material, then inspect each item for any
accidental damage that may have occurred during shipping.
3
5
4
6
You should nd each of these items in your box:
1. Electric Bike
2. Approved Power Adapter / Charging Unit
3. 1- 5mm Allen Wrench
4. 1- 6mm Allen Wrench
5. Battery
6. 2 - Pedals
7. Screws
8. Combination spanner
Remove all packaging material, then inspect each item for any accidental
damage that may have occurred during shipping.
UNPACK
You should find each of these items in your G2 box:
1. G2 Scooter
2. G2 Console & Handlebars
3. Gotrax Approved Power Adapter / Charging Unit
4. Allen wrench
5. Screws
Remove all packing material, then inspect each item for any
accidental damage that may have occurred during shipping.
4
35
UNPACK

GET TO KNOW
YOUR ELECTRIC BIKE
Seat
Throttle Handle
Handlebar
Handle Brake
Tiller
Tiller Fliplock
Safety Lock
Front Brake
Front Wheel
Motor
Seat Post
Seat Post Clamp
Battery
The electric bike comes partially assembled.
GET TO KNOW YOUR ELECTRIC BIKE

Hold the bike and unfold the front
frame.
You will hear a click once the frame
is unfolded. Lock the clamp and turn
the clamp to the left to tighten.
ASSEMBLE YOUR ELECTRIC BIKE
Step 1
Step 2

INSTALL THE TILLER & HANDLEBARS
Use the 5mm Allen Wrench to loosen
the screw and the xed cover.
Take out the sleeve.
Insert the tiller into the head tube, use
the screw and the xed cover to lock it.
Use the 5mm Allen wrench to tighten
it into place.

Turn the top of the tiller iplock
upward and turn the safety lock
counterclockwise until the fold is
locked.
Hold the tiller iplock to the upright
position to ensure the tiller is locked
into position.

ADJUST THE HANDLEBAR ANGLE
ADJUST THE TILLER HEIGHT
Loosen the tiller clamp, adjust the
riller height properly. Lock the clamp
to tighten the tiller in plcae.
Adjust the handlebar to the proper
angle, use the 6mm Allen Wrench to
lock the screw as the gure shows.
Handlebar Adjustent
Tiller Height

ADJUST THE SEAT HEIGHT
INSTALL PEDALS
Use the 15mm spanner to mount the
pedals.
Notice: Turn the left pedal
counterclockwise to tighten; Turn the
right pedal clockwise to tighten.
Loosen the seat post clamp, adjust
the seat properly, lock the clamp to
tighten the seat in place. (see gure)
Seat Adjustent
Pedal Installation

CHARGE YOUR
ELECTRIC BIKE
Before using the E-Bike, you must fully charge the battery.
CHARGE YOUR ELECTRIC BIKE
Before using the electric bike, you must fully charge the battery.

CHARGE YOUR
ELECTRIC BIKE
1. Check Battery Level: Press the power
display button quickly, The charge position
is on the back side of the bike as shown in
the picture.
2. Plug the charging cable into the charging hole(make sure the
connection is dry). Insert the charging plug into the port.
3. The charger box will have a green light when fully charged and a
red light when charging.
4. When you are done charging be sure cover the charging port to
keep it clear of dust and debris.
2. Plug the charging cable into the charging hole(make sure the
connection is dry). Insert the charging plug into the port.
3. The charger box will have a green light when fully charged and a
red light when charging.
4. When you are done charging be sure cover the charging port to
keep it clear of dust and debris.
1. Check Battery Level: Press the
power display button quickly, The
charge position is on the back side of
the bike as shown in the picture.

SCOOTER CONSOLE FUNCTIONS
• The entire controller includes four parts: motor control panel,
head display board, headlight, and taillight.
• All operating experience is done by the three buttons on the
board.
• The entire controller includes four parts: motor control panel, head dis-
play board, headlight, and taillight.
• All operating experience is done by the three buttons on the board.
• The function of the middle button is as follows:
›To power on: Press the button once for 2 seconds to turn on the
screen, once the screen is on so is the bike.
› Topowero: Press the button for 2 seconds until the screen is off,
once the screen is off so is the bike.
ELECTRIC BIKE FUNCTIONS

•The function of the + & - button:
›The electric bike has 3 gears.
» Press the + button to go up in gear.
» Press the - button to go down in gear.
› 1st Gear - 11 MPH
› 2nd Gear - 15 MPH
› 3rd Gear - 20 MPH
• Push Mode: Power on the electric bike, long press the ” -” button for
2 seconds to engage push mode ( Use this when you need a hill assist.)
• Cruise Control
›To Activate: Press the right-hand throttle for 10 seconds while rid-
ing and the cruise control will activate.
›To Deactivate: Press the left or right handbrake to deactivate the
cruise control function.

1. You will want to start riding your electric bike with one foot on the pedal
and one foot on the ground. Use your foot on the ground to push off
and at the same time, press the throttle button to begin movement.
2. Press the brake-throttle to slow down or stop.
3. The electric bike performs best when on a smooth surface e.g. carparks,
smooth roads, footpaths, & bike lanes.
4. Always clean your electric bike (wheels, body, etc.), it’s a machine and
it needs to be maintained.
5. Do not press the throttle while walking with the electric bike beside you.
6. Be aware of the terrain you are riding on, watch out for curbs and
obstacles!
RIDING TIPS

If you regularly clean and maintain your electric bike, it will
extend its life.
Cleaning and storage: If the electric bike is dirty, wipe it clean with a
soft damp cloth.
Brake Adjustments & Service: If you notice you need brake
adjustments or any service on your electric bike, contact our customer
service team and we will adjust and repair your electric bike. Do not
repair your electric bike yourself, this can void your warranty and you risk
damaging the electric bike.
Tires: When there is low pressure in the tire, or the pressure of the two
tires is different, please inate it in time. Make sure the pressure of the two
tires is the same. The default Front & Back tire pressure is 35 to 45 psi.
MAINTENANCE & REPAIR

DO NOT use alcohol, gasoline, kerosene, or other corrosive chemical
solvents to clean the electric bike. It can severely damage the appearance
and structure of the electric bike. Please do not use a pressure washer as
it may also cause damage to the electronics.
Storage: When you’re not using your electric bike store in a dry and
cool location. Avoid storing your electric bike outdoors because sun
exposure can damage it’s appearance and may cause wear on the life of
the battery and tires.

Only use the approved Gotrax power adapter to charge your electric bike,
others may cause risk of re & equipment may be damaged.
Improper disposal of used batteries may seriously pollute the environment.
Please comply with local disposal regulations.
Make sure to store your electric bike and power adapter in conditions that
do not exceed 122 degrees fahrenheit or below -4 degrees fahrenheit.
Warning - Risk of Fire - No User Serviceable Parts, The prolonged
exposure to UV Rays, Rain and the Elements may damage the enclosed
materials, store indoors when not in use.
BATTERY INFORMATION