Great Little Trading Northcote L2505 User manual

1
Northcote Corner Shelf Unit
L2505
easy - medium - hard two-person job 15/02/2018
Thank you for shopping with GLTC, we hope you enjoy having this
product in your home.
We know assembling furniture, toys or accessories is not everyone’s favourite
way to spend their time, so we’ve tried to make assembling this item as quick and
painless as possible.
Hopefully our efforts will have been worthwhile and you’ll sail through the
whole process. But if it all feels a bit too much like hard work, then we do have
an assembly company we can recommend: the Flatpack Construction Company
offers a nationwide service and can be contacted on 0843 289 4951 or www.
.
A few important pointers before you start:
• Please read the instructions right through before you start, and check that all the
piles makes it easier to be sure that everything is present and correct.
• Make sure you have the right tools. Allen keys are provided if required, but screw
beginning of the instructions.
• It’s a good idea to build the unit in the room where you are going to be using it, to
avoid the need to move it after it’s been assembled.
• Do not throw away any packing materials until assembly is complete, just in case you
accidentally discard smaller parts and hardware.
V2
www.gltc.co.uk

2
Safety Warnings:
• Adult assembly required.
• Unassembled product contains small parts which may present a choking hazard.
• Children should be kept away from the product during assembly due to possible
risk of injury.
•
• Do not use power tools in the construction of this product.
• It is recommended that the Northcote modular storage furniture is only stacked
3 units high, inclusive of the base unit.
• Always use the wall straps provided.
• Serious or fatal crushing injuries can occur from furniture falling over. Ensure you
secure this furniture product to the wall before you use it using the kit provided.
If you have not received an anti-tip kit with your product please contact
Customer Services.
• This product is heavy, so we recommend that you build it where you are planning to
use it.
• Check all fixtures and fittings regularly and tighten as necessary.
• Please retain these instructions for future reference.
Customer Service:
•
assembly and do not use the item. Please contact GLTC Customer Services on
0344 848 6000 immediately.
• We do stock spare hardware packs at our warehouse, so we should be able to
send you a replacement pack immediately if required.
Product Care:
• Wipe clean using a soft damp cloth followed by a dry cloth.
• Do NOT use cleaning products which may contain ammonia, solvents or
abrasive material.
• Do NOT expose the furniture to extremes of heat and humidity.
Could we do better?
If there is anything you think could be improved in these instructions or in the
assembly of this product we’d be grateful if you could let us know; we’ll pass
any helpful hints and tips on to other customers via our website and update the
instructions.
All you need to do is drop us a line at [email protected].uk
Thank you

3
Component Check List: All Hardware
#1 #2
#3 #4
21x Cam Dowels
45mmL
21x Cam Locks
14mmDia
18x Wooden Dowels
20mmL
6x Shelf Fixings
15mmL
You will need:
(not supplied)
Philips Head Screwdriver
Component Check List: Corner Shelf Unit
2x Base Panels
(left & right sides)
2x Back Corner Bars
(lower bar in the image is wider, top back bar is thinner)
2x Top Panels
(left & right sides)
2x Side Panels
(left & right sides)
4x Back Panels
2x Shelf Panels
(left & right sides)
A
B
C
D
E
F

4
Assembly
STEP 1:
Insert 2x cam dowels (#1) and 2x wooden dowels (#3) into the diagonal edge of the left hand base
panel (A).The wooden dowels go into the larger holes.
Insert 1x cam dowel (#1) into the diagonal edge of the right hand base panel (A).
Do not use force or a hammer as the wood may split.
Hardware for Step 1:
3x #1 Cam Dowels
2x #3 Wooden Dowels
#3
#1
#1
#3
#1
A A
When in position, turn the 3x
cam locks (#2) on the base
panel (A) clockwise to lock in
place.
STEP 2:
Push the two base panels (A) together.
Insert 3x cam locks (#2) into the large drill holes along the edge of the joined components.The arrows
should point towards the connecting edge of the base panels (A).Turn all of the cam locks (#2) clockwise
to lock.
Ensure that each cam lock’s arrow is
pointing towards the drill hole on the side
edge of the component.
Hardware for Step 2:
3x #2 Cam Locks
#2
left right
A A
left right

5
STEP 3:
Turn the joined base panel (A) over.
Insert 2x cam dowels (#1) and 2x wooden dowels (#3) into the holes at the back point of the base panel
(A) as shown.
Hardware for Step 3:
2x #1 Cam Dowels
2x #3 Wooden Dowels
A
#1
#3
STEP 4:
Slide the thinner back corner bar (B) onto the hardware on the left hand side, making sure the side groove
lines up with those on the base panel (A).Also make sure the large drill hole is facing backwards on thinner
back corner bar (B).
Repeat the process with the wider back corner bar (B), placing it on the right hand side, lining up the
grooves and ensuring the large drill hole is facing backwards.
A
B B
Thin Part Wide Part

6
STEP 5:
Insert 2x cam locks into the large drill holes on the back of the back
corner bars (B), with the arrows facing down and turn clockwise to
lock.
A
B B
Thin Part Wide Part
Hardware for Step 5:
2x #2 Cam Locks
When in position, turn the 2x
cam locks (#2) clockwise to lock
in place.
STEP 6:
with the grooves and large drill holes facing up.
Insert 2x cam dowels (#1) and 2x wooden dowels (#3) into the
diagonal edge of the left hand top panel (C).The wooden dowels go
into the larger holes.
Insert 1x cam dowel (#1) into the diagonal edge of the right hand
top panel (C).
Hardware for Step 6:
3x #1 Cam Dowels
2x #3 Wooden Dowels
#3
#1
#1
#3
#1
C C
left right

7
C
When in position, turn the 3x
cam locks (#2) on the top panel
(C) clockwise to lock in place.
STEP 7:
Push the two top panels (C) together.
Insert 3x cam locks (#2) into the large drill holes along the edge of the joined components.The arrows
should point toward the connecting edge in the top panel.
Turn all of the cam locks (#2) clockwise to lock.
Ensure that each cam lock’s arrow is
pointing towards the drill hole on the side
edge of the component.
Hardware for Step 7:
3x #2 Cam Locks
C C
#2 STEP 8:
Insert 2x cam dowels (#1)
and 2x wooden dowels (#3)
into the holes at the back
corner of the top panel (C)
as shown.
Hardware for Step 8:
2x #1 Cam Dowels 2x #3 Wooden Dowels #1
#3
A
B
B
Thin Part
Wide Part
STEP 9:
Position the joined base panel (A)
and back corner bars (B) on their
side, as shown.

8
Hardware for Step 12:
4x #1 Cam Dowels
4x #3 Wooden Dowels
A
C
B
STEP 10:
Attach the joined top panel (C) to the
back corner bars (B).
Insert 2x cam locks into the two
remaining large drill holes on the back
of the two back corner bars (B), with
the arrows facing towards panel C and
turn clockwise to lock.
When inserting the cam lock (#2) on
the underside of the back corner bar
(B), be careful when manoeuvering the
unit.We highly recommend getting a
second person to help at this stage.
STEP 11:
Slide the four back panels (E) into the
inside grooves of the top panel (C) &
base panel (A) as shown.
STEP 12:
Take the left side panel (D) and lay
Insert 4x cam dowels (#1) and
4x wooden dowels (#3) into the
corners of the left side panel (D).
The wooden dowels go into the
larger holes.
Turn the 2x cam locks (#2)
on the back corner bars (B)
clockwise to lock in place.
Hardware for Step 10:
2x #2 Cam Locks
#2
C
D
A
E
E
left side
#1
#3
two-person job

9
STEP 13:
Place the left side panel (D) onto the sides of the top and base panels (A
and C) as shown, making sure the groove lines up with the back panel (E)
and the ‘teeth’ are facing downwards.
Insert 2x cam locks (#2) into the large drill holes on the underside of
the base panel (A), and 2x cam locks (#2) into the large drill holes on the
inside of top panel (C).Turn all these clockwise to lock.
Hardware for Step 13:
4x #2 Cam Locks
A
C
D
left side
Turn the cam locks (#2) on
the back of panels C & A
clockwise to
lock in place.
#2
STEP 14:
Take the two shelf panels (F) and lay them on a clean at surface,
with the large drill holes facing up.
Insert 2x cam dowels (#1) and 2x wooden dowels (#3) into the
diagonal edge of the left hand shelf panel (F).The wooden dowels go
into the larger holes.
Insert 1x cam dowel (#1) into the diagonal edge of the right hand
shelf panel (F).
Hardware for Step 14:
3x #1 Cam Dowels
2x #3 Wooden Dowels
#3
#1
#1
#3
#1
left side
F
right side
F

10
When in position, turn the 3x
cam locks (#2) on the shelf
panels (F) clockwise to lock
in place.
STEP 15:
Push the two shelf panels (F) together.
Insert 3x cam locks (#2) into the large drill holes along the edge of the joined components.The arrows
should point toward the connecting edge in the shelf panel.Turn all of the cam locks (#2) clockwise to lock.
STEP 16:
Choose your shelf height and insert 4x shelf xings (#4) on the inside of the part built unit. Two on the left
side panel (D) and two on the back corner bars (B). The nal two pegs will be applied to the right side panel
(D), once in place.
Ensure that each cam lock’s arrow is
pointing towards the drill hole on the side
edge of the component.
Hardware for Step 15:
3x #2 Cam Locks
#2
left side
F
right side
F
Hardware for Step 16:
4x #4 Shelf Fixings
D
B
left side
#4