Great Little Trading Lulworth User manual

1
Lulworth Wardobe
12/07/2021
V1
two-person job
Assembly Difculty
easy - medium - hard
A few important pointers before you start:
• Please read the instructions right through before you start, and
check that all the components have been included in the pack;
we nd separating all the hardware into piles makes it easier to
be sure that everything is present and correct.
• Make sure you have the right tools.Allen keys are provided
if required, but screw drivers and other tools are not.You’ll
nd details of the tools you need at the beginning of the
instructions.
• It’s a good idea to build the unit in the room where you are
going to be using it, to avoid the need to move it after it’s been
assembled.
• Do not throw away any packing materials until assembly is
complete, just in case you accidentally discard smaller parts or
hardware.
Thank you for shopping with GLTC, we hope you enjoy
having this product in your home.
We know assembling furniture, toys or accessories is not everyone’s
favourite way to spend their time, so we’ve tried to make assembling
this item as quick and painless as possible.

2
Safety Warnings:
• IMPORTANT: PLEASE RETAIN THESE INSTRUCTIONS FOR FUTURE
REFERENCE.
• Adult assembly required.
• Unassembled product contains small parts which may present a
choking hazard.
• Children should be kept away from the product during assembly to
avoid any possible risk of injury.
• Assemble and use on a at and level surface.
• This product is suitable for children aged 3 years+.
• Maximum weight for shelves and hanging rail is 25kgs.
• DO NOT use power tools in the assembly of this product as there is a
risk of over-tightening and consequently splitting of the wood.
• To avoid possible injury from tipping, DO NOT allow children to climb
on the product.
• Always use the wall straps provided.
• WARNING! FURNITURE TIPPING RISK. Serious or fatal crushing
injuries can occur from furniture tipping over. Ensure you secure this
furniture product to the wall before you use it, using the kit provided.
If you have not received an anti-tip kit with your product please
contact Customer Services.
• Check all xtures and ttings regularly and tighten as necessary.
Customer Service:
• If you nd that any components are missing or damaged, please do
not begin assembly and do not use the item. Please contact GLTC
Customer Services on 0344 848 6000 immediately.
• We do stock spare hardware packs at our warehouse, so we should be
able to send you a replacement pack immediately if required.
Product Care:
• Wipe clean using a soft damp cloth followed by a dry cloth.
• Do NOT use cleaning products which contain ammonia, solvents or
abrasive material.
• Do NOT expose the item to extremes of heat and humidity.
• Regularly check all fastenings, xtures and ttings to ensure that they
properly tightened.
Could we do better?
If there is anything you think could be improved in these instructions or in
the assembly of this product we’d be grateful if you could let us know; we’ll
pass any helpful hints and tips on to other customers via our website and
update the instructions.
All you need to do is drop us a line at [e-mail]
Thank you

3
Component Check List Component Check List
A MB N
C OD P
F R
H T
I
K
UJ
L
E Q
G S
You will need
(not supplied)
Philips Head Screwdriver
1x Upper LH Side Panel 1x RH Drawer Side Panel
1x Drawer Back Panel
1x Hanging Rail
1x Right Door
1x Adjustable Shelf
2x Back Rails
1x Mid Panel
1x RH Lower Side Panel
1x Upper Back Panel
1x Lower Back Panel
1x Upper RH Side Panel 1x Drawer Front Panel
1x Drawer Base Panel
1x Left Door
4x Feet
1x Top Panel
1x LH Lower Side Panel
1x Base Panel
1x Middle Back Panel
1x LH Drawer Side Panel
1x Anti-Tip Kit

4
Hardware Check List
#1 #13#2 #14
#3 #15#4 #16
#6 #18
#8 #20
#10 #22
#11 #12 #23
#9 #21
#5 #17
#7 #19
24x Cam Dowels 1x LH ‘L-Shaped’ Runner
2x Rail Mount Plates
Note: These plates may come
connected to Part #15, please
unscrew to separate.
6x Cross-Head Barrel Nuts
24x Screws
(4mm x 12mmL)
26x Screws
(16mmL)
1x RH Flat Runners
2x Collars
6x Hinges
4x Crosshead Bolts
(24mm)
6x Crosshead Bolts
(47mm)
4x Pegs
(16mm)
24 x Cam Locks 4 x Screws
(25mmL)
20x Wooden Dowels
10x Hex Bolts
(42 mm)
16x Screws
(3.5mm x 12mmL)
1x LH Flat Runner
1x RH ‘L-Shaped’ Runner
6x Hinge Base Plates
1x Allen Key
4x Handles
6x Slotted Barrel Nuts
22
22
22
22
Hardware Check List

5
Hardware for Step 1:
STEP 1:
Firstly, decide on the desired height of the hanging rail.
There are three positions to choose from. The illustration shows the use of
the recommended middle position that gives you the use of the rail and also
allows you to use the shelf (see later step).
The lower position can be used when the child is younger or their clothes are
shorter.
The highest position is there for when the child is older and their clothes are longer.
Please note: this higher position does require the removal of the shelf.
Once the position is decided, attach the 2x rail mounting plates (#3) to
BOTH side panels (A & B) using 4x screws (#8).
Please ensure you use the correct #8 hardware here.There is a similar sized
hardware used later. Please use the thinner screws here.
Now, using a Philips screwdriver, insert 4x cam dowels (#1) into the holes
along the edge of BOTH side panels as shown.
Hardware for Step 2:
6x #1 Cam Dowels
8x #1 Cam Dowels
2x #3 Rail Mount Plates
4x #8 Screws
(3.5mm x 12mmL)
STEP 2:
Using a Philips screwdriver, prepare top panel (D) by inserting 6x cam dowels
(#1) in the holes shown.
Note: The block on the underside of the panel indicates the front of the panel.
Please note the correct position of this hardware - there are more drill holes here
that will be used on the next stages.
STEP 3:
Note: Two people are needed for this step.You will be building this wardrobe
face up, so the back of the unit will be on the oor.
Align panels (A) and (B) as shown ensuring that the groove along the long
edge is to the oor. Position and connect 2x panels (C) ensuring the large drill
holes are facing down so you cannot see them.
DO NOT turn the unit over to x these panels in place, this step will be
completed at a later stage.
#8
#8
#1
#1
#1
#1
#1
#1
#1
#3
#3
FRONT
TOP
TOP
BASE
TOP
BACK
BACK
BASE
BASE
BACK
BACK
A
B
2x
2x
2x
2x
2x
2x
#1
#1
#1
D
A
B
C
C

6
STEP 5:
Prepare panel (E) by inserting 6x cam dowels (#1) as
shown.
Please note the correct position of this hardware - there are
more drill holes here that will be used on the next stages.
STEP 4:
Insert 4x wooden dowels (#4) into the remaining inner holes on top panel (D)
and connect to side panels (A) and (B).
Insert 6x cam locks (#2) into the large drill holes on both side panels and turn
clockwise to secure.
Note the orientation of panel D - grooved edge to the oor and rounded corners and
block to be uppermost.
Hardware for Step 5:
6x #1 Cam Dowels
Hardware for Step 4:
6x #2 Cam Locks
4x #4 Wooden Dowels
TOP
BASE
FRONT
A
B
D
#2
#4
#4
#4
#4
#2
#2
#2
#2
#2
E
#1
#1
#1
#1
#1
#1
Using Cam Locks:
When inserting into the panel, ensure that each
cam lock’s arrow is pointing towards the drill hole
on the side edge of the panel & the dowel that it
will be receiving.
When the panels are in the connected position,
using a screwdriver, turn the cam lock in a
clockwise direction to lock and secure.

7
STEP 6:
Insert 4x wooden dowels (#4) into the ends of panels (A
& B) as shown and then connect panel (E) to these ends.
Ensure that the grooved edge of panel (E) is facing the
oor and the metal hardware is facing outwards towards
the base of the unit.
When panel (E) is in place, insert 6x barrel nuts (#5) into
the holes on the side panels (A & B) ensuring the hole in
the nut is facing towards the base. Secure panel (E) with
6x hex bolts (#6) using the Allen key provided.
#5
BASE
E
A
B
#5
#4
#4
#6
#6
#6
#6
#6
#6
#4
#4
#5
Hardware for Step 6:
4x #4 Wooden Dowels
6x #5 Barrel Nuts
6x #6 Hex Bolts (42mm)
#5
STEP 7:
Attach LH at runner (#10) to panel (F) and RH at runner (#11) to panel
(G) as shown ensuring that you are positioning the x6 screws (#8) through
the indicated holes.
When xed in the correct position, the runner wheel will be next to the smaller set
of holes on the lower edge of the panels, at the opposite end of the panel to the
grooved edge and there will also be a gap between the front edge of the panel and
the start of the runner. If the front of runner (wheel) is level with the front edge of
the panel, it is in the wrong position.
Ensure the hardware is fully inserted for smooth drawer opening.
Hardware for Step 7:
6x #8 Screws (3.5mm x 12mmL)
1x #10 LH Flat Runner
1x #11 RH Flat Runner
#8
#8
#8
#8
#8
#8
F
G
#10
#11
F
G

8
STEP 8:
Insert 4x wooden dowels (#4) into the remaining
holes on panel (E) and connect side panels (F)
and (G) as shown ensuring that the wheel of the
runners is at the top and the grooved edge is on
the oor. Secure these panels with 6x cam locks
(#2), turning clockwise to lock.
Note: The runners should be sitting at the bottom
edges with the wheel at the front of the unit.
Hardware for Step 8:
6x #2 Cam Locks
4x #4 Wooden Dowels
E
F
G
#4
#4
#4
#4
#2 #2
#2
#2
#2
#2
STEP 9:
Insert 4x wooden dowels (#4) into the ends of
panels (F & G) as shown and then 6x slotted
barrel nuts (#22) into the holes on the sides of
these panels.
Position base panel (H) and then insert 6x
slotted barrel nuts (#22) to the ends of side
panels (F & G) using the dowels. Ensure that
the rounded corners of panel (H) are facing up
and the grooved edge is on the oor.
Secure panel (H) with 6x bolts (#21) as shown,
using the Allen key provided.
Hardware for Step 9:
4x #4 Wooden Dowels
6x #21 Crosshead Bolts (47mmL)
6x #22 Slotted Barrel Nuts
H
G
F
#4
#22
#22
#21
#21
#21
#21
#21
#21
#4
#4
#4
3x
3x

9
#6
STEP 10:
Note: Two people are needed to complete
the next step safely.
Carefully turn the unit over so the back is
facing up. Insert 8x cam locks (#2) into the
large drill holes on the 2x back panels (C).
Turn clockwise to lock.
Then attach the 4x feet (T) to the base
panel (H). Insert 4x wooden dowels (#4) on
base panel (H) as indicated, push the feet in
position and secure with 4x bolts (#6) using
the Allen key provided.
Hardware for Step 10:
8x #2 Cam Locks
4x #6 Hex Bolts (42 mm)
4x #4 Wooden Dowels
#4
#6
#2
#2
#2
#2
#6
#4
#4
#4
2x
2x
2x
2x
C
C
T
H
T
T
T
STEP 11:
Place back panels (I), (J) and (K) onto the
grooved edge on the back of the unit as
shown, ensuring that the holes in the panels
align with the pilot holes on the edge of the
unit. Secure all 3 panels with 26x screws (#9).
Please note that the 2x pilot holes circled at
the top/side of the unit are to attach anti-tip
straps included separately with this item. See
step 21 for more details.
With the help of a second person, you can
now stand the wardrobe on its feet.
Hardware for Step 11:
26x #9 Screws (16mmL)
#9
26x
I
J
K
Anti-tip kit
Anti-tip kit

10
STEP 12: Create the Drawer.
Attach LH ‘L-shaped’ runner (#13) to
drawer side panel (L) as shown with 3x
screws (#8).
The runner will t the full length of the
panel and should be positioned with the
wheel at the end next to the 2 small drill
holes as shown. It should NOT be on the
side with the groove.
REPEAT with drawer side panel (M) and
RH L-shaped runner (#12).
Ensure the screws are fully inserted to
allow the drawer to run smoothly
Hardware for Step 12:
6x #8 Screws (3.5mm x 12mmL)
1x #13 LH ‘L-Shaped’ Runner
1x #12 RH ‘L-Shaped’ Runner
L
#8
#8
#8
#8
#8
#8
#13
M
#12
#8
#8
#8
#13
STEP 13:
Prepare drawer front panel (N) by inserting
4x cam dowels (#1) as shown and attach 2x
handles (#20) with 2x bolts (#19).
Hardware for Step 13:
4x #1 Cam Dowels
2x #19 Crosshead Bolts (24mm)
2x #20 Handles
#1
#1
#19
#19
#20
#20
#1
#1
N