Great Little Trading L5166 User manual

1
Wooden Play & Shop Cafe
26/04/2021
V1
easy - medium - hard
Assembly Difculty
one-person job
L5166
A few important pointers before you start:
• Please read the instructions right through before you start, and
check that all the components have been included in the pack;
we nd separating all the hardware into piles makes it easier to
be sure that everything is present and correct.
• Make sure you have the right tools.Allen keys are provided
if required, but screw drivers and other tools are not.You’ll
nd details of the tools you need at the beginning of the
instructions.
• It’s a good idea to build the unit in the room where you are
going to be using it, to avoid the need to move it after it’s been
assembled.
• Do not throw away any packing materials until assembly is
complete, just in case you accidentally discard smaller parts or
hardware.
Thank you for shopping with GLTC, we hope you enjoy
having this product in your home.
We know assembling furniture, toys or accessories is not everyone’s
favourite way to spend their time, so we’ve tried to make assembling
this item as quick and painless as possible.

2
Safety Warnings:
• Adult assembly required.
• Not suitable for children under 3 years due to small parts that may
present a choking hazard.
• Assemble and use on a at and level surface.
• Unassembled product contains small parts which may present a
choking hazard
• Children should be kept away from the product during assembly to
avoid any possible risk of injury.
• DO NOT use power tools in the assembly of this product as there is a
risk of over-tightening and consequently splitting of the wood.
• Check all xtures and ttings regularly and tighten as necessary.
• Check the item regularly for signs of damage which may make the
product unsafe.
• Dispose of packaging carefully to avoid injury to young children.
• Please retain these instructions for future reference.
Customer Service:
• If you nd that any components are missing or damaged, please do
not begin assembly and do not use the item. Please contact GLTC
Customer Services on 0344 848 6000 immediately.
• We do stock spare hardware packs at our warehouse, so we should be
able to send you a replacement pack immediately if required.
Product Care:
• Wipe clean using a soft damp cloth followed by a dry cloth.
• Do NOT use cleaning products which contain ammonia, solvents or
abrasive material.
• Do NOT expose the item to extremes of heat and humidity.
Could we do better?
If there is anything you think could be improved in these instructions or in
the assembly of this product we’d be grateful if you could let us know; we’ll
pass any helpful hints and tips on to other customers via our website and
update the instructions.
All you need to do is drop us a line at [e-mail]
Thank you
Registered Address:
GLTC Ltd, 12 Buckhold Road,
Wandsworth, London, SW18 4GP, United Kingdom
Authorised Representative:Authorised
Representative Service, 77 Camden Street Lower,
Dublin, D02 XE80, Ireland

3
Component Check List
A
1x 4x 1x
2x 1x 1x
B C
D E F
1x 1x
1x
1x 1x
1x
1x
1x
GHI
J K L
2x
1x
1x
M N
P
#1 #2 #3
#4 #5 #6
#7 You will need
(not supplied)
Phillips Head Screwdriver
QR
1x
18x Bolts
4x Screws 21mm
16x Screws 30mm 18x Barrel nuts
4x Bolts 4x Bolts
2x Allen Keys
O

4
STEP 1:
Attach 4x feet (part B) onto panel A using 8x
screws (#1).
STEP 2:
Attach panel C to panel A using 2x barrel nuts (#2) and
2x bolts (#3).
Hardware for Step 2:
2x #2 Barrel nuts
2x #3 Bolts
Hardware for Step 3:
Hardware for Step 4:
2x #2 Barrel nuts
2x #3 Bolts
2x #2 Barrel nuts
2x #3 Bolts
STEP 3:
Attach panels D (2x) to panel C using 2x barrel nuts (#2) and 2x bolts (#3)
Ensuring the front ledge is facing the correct way.
STEP 4:
Attach panels E and F to panel C using 2x barrel nuts (#2) and 2x bolts (#3).
Note- panel F has two additional drill holes at the top, this needs to placed above
panel E.
AD
D
#1 #1
#1
#1
#1 #1
#1
#1
#2
#2
#3
#3
#3
#3
#3
#3
#2
#2
F
E
C
C
Hardware for Step 1:
8x #1 Screws 30mm
B
B
B
B
#2
#2
#2
A
C

5
Hardware for Step 5:
2x #2 Barrel nuts
2x #3 Bolts
STEP 5:
Carefully turn the shop on its side, onto panel C.
Attach panel G to the base panel A using 2x barrel nuts (#2) and 2x bolts (#3).
STEP 6:
Further secure panel G by using 4x barrel nuts (#2) and 4x bolts (#3).
STEP 7:
Secure part H to side panel using 1x screw (#1).
G#3
#3
Hardware for Step 6:
4x #2 Barrel nuts
4x #3 Bolts
Hardware for Step 7:
1x #1 Screw 30mm
H
I
#1
STEP 8:
Slot in panel I into the centre of the
base. Ensure drill holes are facing the
correct way- use shelf ledge to guide
you.
#2
#2
#2
#2
#2
#2
#3 #3
#3 #3
C
G
A

6
STEP 9:
Secure panel I using 2x screws (#4).
STEP 10:
Attach panel J (shop worktop) to base of the
shop using 2x barrel nuts (#2) and 2x bolts (#3)
and 1x screw (#1).
STEP 11:
Attach part L to panel K using 2x screws (#1).
STEP 12:
Attach part M to panel K using 2x screws (#1)
L
K
K
#1
#1
#1
#1
#3
#3
#1
Hardware for Step 10:
2x #2 Barrel nuts
1x #1 Screw 30mm
2x #3 Bolts
Hardware for Step 11:
Hardware for Step 9:
2x #1 Screws 30mm
2x #4 Screws 21mm
M
J
Hardware for Step 12:
2x #1 Screws 30mm
#4
#4
#2
#2
I

7
STEP 13:
Attach part L to panel N using 2x screws (#1)
STEP 15:
Insert panel K into the top
of panel J (worktop).
Secure panel K using 2x
bolts (#5) and 2x bolts (#6)
using the Allen Key (#7)
provided to tighten them
together.
L
N
N
Hardware for Step 14:
Hardware for Step 13:
Hardware for Step 15:
2x #4 Screws 21mm
2x #1 Screws 30mm
2x #5 Bolts
2x #6 Bolts
1x #7 Allen Key
STEP 14
Attach part O (clock) to panel N using 2x screws (#4).
#1
#4
#4
#5
#6
#6
#7
#7 #6
#5
#5
#1
OHardware for Step 16:
2x #5 Bolts
2x #6 Bolts
1x #7 Allen Key
K
J
N#7 #7
#6
#5
Insert panel N into the
top of panel J (worktop)
Secure panel N using 2x
bolts (#5) and 2x bolts
(#6) using the Allen Key
(#7) provided to tighten
them together.
J

8
Copyright© 2021 G.L.T.C. Ltd. All rights reserved.
Great Little Trading Company and GLTC are registered trade marks of G.L.T.C. Limited.
STEP 19:
Hang your shop open & close sign (part R).
Hardware for Step 17:
4x #2 Barrel Nuts
4x #3 Bolts
STEP 18:
P
P
Q
#3
#3
#2
#2 #2
#2
#3
#3
Loosely attach panel P to the
side panels (K & N) using 4x
barrel nuts (#2) and 4x bolts
(#3).
Insert panel Q using
the dowels (already
attached to the panel)
into panel (K &N).
Now go back and
secure the bolts and
nuts from step 18,
tighten panel P.
N
K
K
N