Grizzly CLAMP RACK User manual

CLAMP RACK
ASSEMBLY INSTRUCTIONS
Save time in the shop today with this mobile clamp rack
build from Grizzly Industrial Inc. Designed by CEO &
Founder of Grizzly Industrial, Shiraz Balolia, this rack
ensures you have what you need at an arm’s length. It
holds F-style clamps, C-clamps, parallel and tube clamps.
This project breakdown features a full material and cut list,
overview drawing and list of components found
on grizzly.com.
©Copyright Grizzly Industrial, Inc., 2020

CLAMP RACK
ANATOMIC VIEW
©Copyright Grizzly Industrial, Inc., 2020
BASE
(TWO LAYERS OF 1" PLYWOOD SHOWN,
MAY BE SUBSITUTED FOR BUTCHER BLOCK
OR OTHER SIMILAR MATERIAL)
PANEL BASE FRAME
(FRONT END AND SIDE PANELS REMOVED FOR CLARITY)
SHELF
END PANEL
SIDE PANEL
LEDGER
TOP BRACE

CLAMP RACK
CUT SHEET
©Copyright Grizzly Industrial, Inc., 2020
END PANEL
245/8" x 48"
END PANEL
245/8" x 48"
123/8"
2 x 4 x 96"
(45° CUTS)
FOR PANEL
BASE FRAME
2 x 4 x 96"
FOR TOP BRACES
AND LEDGERS
48" x 96" x ¾"
PLYWOOD
48" x 96" x ¾"
PLYWOOD
123/8"123/8"123/8"
SIDE PANEL
243/8" x 48"
SIDE PANEL
243/8" x 48"
SHELF
123/8" x 243/8"
BASE
245/8" x 36"
BASE
245/8" x 36"
123/8"
123/8"243/8"
243/8"

CLAMP RACK
LIST OF ADDITIONAL MATERIALS
©Copyright Grizzly Industrial, Inc., 2020
STEEL ANGLE
FOR PANEL BASE 3" X 3" X 3/16" 2 @ 24½"
FOR TOP C-CLAMP HOLDER 2" X 2" X 1/8" 2 @ 24½"
CLAMP RACK
SHOP FOX D4345 3-PIECE SET AVAILABLE ON GRIZZLY.COM
(USED AS-SHOWN IN PHOTO)
CASTERS
STEELEX D2570 4" FIXED CASTERS (MAX. 2) AVAILABLE ON GRIZZLY.COM
STEELEX D2610 4" LOCKING SWIVEL CASTERS (MAX. 2 OR USE 4) AVAILABLE ON GRIZZLY.COM
FASTENERS
WOOD SCREWS (1¼" & 2")
LAG BOLTS (16) AND WASHERS (32) FOR CASTERS
HEX BOLTS (12), WASHERS (24) AND LOCKING NUTS (12) FOR STEEL ANGLE

CLAMP RACK
BUILD INSTRUCTIONS PAGE 1 of 4
©Copyright Grizzly Industrial, Inc., 2020
• STACK BASES AND SECURE WITH WOOD SCREWS,
AVOIDING CASTER AND PANEL BASE
FRAME AREA.
• FLIP BASE OVER. PLACE PANEL BASE FRAME
IN CENTER OF BASE AND FASTEN WITH
WOOD SCREWS.
• ATTACH CASTERS WITH BOLTS AND WASHERS.

CLAMP RACK
BUILD INSTRUCTIONS PAGE 2 of 4
©Copyright Grizzly Industrial, Inc., 2020
• DRILL HOLES IN 3" X 3" STEEL ANGLES.*
• FIT SIDE PANEL AND STEEL ANGLE TO PANEL
BASE FRAME AND FASTEN WITH BOLTS.
REPEAT ON OTHER SIDE.
PANEL BASE FRAME
SIDE PANEL
1½"
2¼"
SIDE PANEL BOLT
BASE
*NOTE:
DRILL VERTICAL HOLES 2¼"
FROM BOTTOM EDGE TO
PROVIDE CLEARANCE FOR
PANEL BASE FRAME

CLAMP RACK
BUILD INSTRUCTIONS PAGE 3 of 4
©Copyright Grizzly Industrial, Inc., 2020
• ATTACH LEDGERS, SHELF, TOP BRACES,
AND FASTEN WITH WOOD SCREWS.
• ATTACH END PANELS AND FASTEN
WITH WOOD SCREWS.

CLAMP RACK
BUILD INSTRUCTIONS PAGE 4 of 4
©Copyright Grizzly Industrial, Inc., 2020
• DRILL HOLES IN 2" X 2" STEEL ANGLES.
• ATTACH STEEL ANGLES TO TOP BRACES
AND FASTEN WITH WOOD SCREWS.
• ATTACH CLAMP RACKS WHERE DESIRED
AND FASTEN WITH WOOD SCREWS.
Enjoy your new
clamp rack!