Grizzly T25091 User manual

For questions or help with this product contact Tech Support at [phone] or [e-mail]
MODEL T25091
84" x 26" HEAVY-DUTY
WORKBENCH
INSTRUCTIONS
Table Dimensions ............................... 84 x 26 in.
Table Thickness .........................................11⁄2 in.
Finish ..........................................Lacquer Sealed
Upper Drawers ........................25 x 61⁄2 x 141⁄2 in.
Lower Drawers ........................25 x 93⁄4 x 141⁄2 in.
Weight .....................................................250 lbs.
SpecificationsIntroduction
Thank you for purchasing the Grizzly T25091
Heavy-Duty Workbench. The part numbers refer-
enced throughout the assembly steps correspond
with the fasteners shown in the inventory photo
below, and the parts breakdown shown on Page 7.
COPYRIGHT © JANUARY, 2013 BY GRIZZLY INDUSTRIAL, INC.
NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE
OR FORM WITHOUT THE WRITTEN APPROVAL OF GRIZZLY INDUSTRIAL, INC.
#ST15576 PRINTED IN TAIWAN
WOOD SCREW (#7)
TWIST-LOCK
NUT (#8)
TWIST-LOCK
DOWEL SCREW (#9)
FLAT WASHER
6MM (#24)
LOCK WASHER
6MM (#25)
HEX WRENCH
(#30)
FURNITURE SCREW
M6-1 X 45 (#28)
DOWEL
(#10)
FURNITURE SCREW
M6-1 X 75 (#27)
FURNITURE SCREW
M6-1 X 90 (#29)
DOWEL NUT
M6-1 (#11)

-2- T25091 Heavy-Duty Workbench (Mfg. 1/13+)
2. Insert four dowels (#10) into the shelf (#13). Attach the shelf (#13) to the left support panel (#15), then
secure with two dowel nuts (#11), two flat washers (#24), two lock washers (#25), and two furniture cap
screws (#29).
1. Insert four dowels (#10) into the rear support panel (#12). Attach the left support panel (#15) to the rear
panel (#12) using the dowels for alignment and securing with two dowel nuts (#11), two flat washers (#24),
two lock washers (#25), and two furniture cap screws (#29).
Assembly
10
13
11
10
11
15
24
24
25
25
29
29
10
12
11
10
15
24
24
25
25
29
29

T25091 Heavy-Duty Workbench (Mfg. 1/13+) -3-
3. Insert two dowels (#10) into the top of the partition panel (#14). Attach the partition panel (#14) to the
shelf (#13) with two dowel nuts (#11), two flat washers (#24), two lock washers (#25), and two furniture cap
screws (#28).
4. Insert one dowel (#10) into each end of the front support panel (#17) and rear support panel (#18). Insert
one dowel into the top of the rear support panel (#18). Attach the front (#17) and rear (#18) support panels
to the left support panel (#15) and partition panel (#14), then secure with three dowel nuts (#11), three flat
washers (#24), three lock washers (#25), and three furniture cap screws (two of #28 and one of #29).
11
25
28
24
13
10
14
15
24
28
29
25
25
24
14
11
10
10
10
10 11 18
10
28
17
11
24
25

-4- T25091 Heavy-Duty Workbench (Mfg. 1/13+)
6. Secure the workbench top (#1) to the left support panel (#15) and right support panel (#16) using six flat
washers (#24), six lock washers (#25), and six furniture cap screws (four of #27 and two of #28). Secure the
adjustable foot pad (#31) to the bottom of the rear support panel (#18). Adjust as necessary to ensure that
foot touches the ground for support.
1
27
28
27
25
24
16
18
31
15
27
28
24
25
27
5. Secure the right support panel (#16) to the assembly with six dowel nuts (#11), six flat washers (#24), six
lock washers (#25), and six furniture cap screws (one of #28 and five of #29).
13 10
16
29
28
29
25
24
10
11
17
18

T25091 Heavy-Duty Workbench (Mfg. 1/13+) -5-
7. Insert the large drawer bottom panel (#21) into both the large drawer front panel (#20) and the large
drawer rear panel (#22). Secure the large drawer rear panel (#22) to the large drawer bottom panel (#21)
using four wood screws (#7).
22
7
21
20
8. Insert two dowels (#10) into each side of the rear drawer panel (#22). Attach the large drawer panels (#19
and #23) to the large drawer assembly using three wood screws (#7) on each side in the back, and three
twist-lock nuts (#8) and three twist-lock dowel screws (#9) on each side in the front.
9. Repeat Steps 7–8 to assemble the remaining large drawer.
8
19
710
22
9
10
7
23
8

-6- T25091 Heavy-Duty Workbench (Mfg. 1/13+)
10. To assemble the small drawers, repeat Steps 7–8, but only use two wood screws (#7) on each side in
the back and two twist-lock nuts (#8) and two twist-lock dowel screws (#9) on each side in the front.
4
3
8
2
7
5
7 6
8
11. Fit each drawer between two slides on the drawer mounting block and push them all the way in.

T25091 Heavy-Duty Workbench (Mfg. 1/13+) -7-
1
4
4
5
5
10 7
7
7
7
28
68
9
10
7
2
8
3
3
9
6
11
11
10
12
28 28
13
10
27
28 27
29
28 29 25
24
15
10
31
18
10
10
14
17
28
24
25
723
8
9
20
22 10
7
7
19
23
8
9
20
8
19
7
7
10
22
30
27
28
27
25
24
16
21
21
T25091 Parts Breakdown and List
REF PART # DESCRIPTION QTY REF PART # DESCRIPTION QTY
1 PT25091001 WORKBENCH TOP 1 16 PT25091016 RIGHT SUPPORT PANEL 1
2 PT25091002 SMALL DRAWER RIGHT PANEL 2 17 PT25091017 FRONT SUPPORT PANEL 1
3 PT25091003 SMALL DRAWER FRONT PANEL 2 18 PT25091018 REAR SUPPORT PANEL 1
4 PT25091004 SMALL DRAWER BOTTOM PANEL 2 19 PT25091019 LARGE DRAWER RIGHT PANEL 2
5 PT25091005 SMALL DRAWER REAR PANEL 2 20 PT25091020 LARGE DRAWER FRONT PANEL 2
6 PT25091006 SMALL DRAWER LEFT PANEL 2 21 PT25091021 LARGE DRAWER BOTTOM PANEL 2
7 PT25091007 WOOD SCREW M4 X 30 36 22 PT25091022 LARGE DRAWER REAR PANEL 2
8 PT25091008 TWIST-LOCK NUT 20 23 PT25091023 LARGE DRAWER LEFT PANEL 2
9 PT25091009 TWIST-LOCK DOWEL SCREW 20 24 PW03M FLAT WASHER 6MM 21
10 PT25091010 WOOD DOWEL M8 X 30 34 25 PLW03M LOCK WASHER 6MM 21
11 PT25091011 DOWEL NUT M6-1 15 27 PT25091027 FURNITURE CAP SCREW M6-1 X 75 4
12 PT25091012 REAR PANEL 1 28 PT25091028 FURNITURE CAP SCREW M6-1 X 45 7
13 PT25091013 SHELF 1 29 PT25091029 FURNITURE CAP SCREW M6-1 X 90 10
14 PT25091014 PARTITION PANEL 1 30 PAW04M HEX WRENCH 4MM 1
15 PT25091015 LEFT SUPPORT PANEL 1 31 PT25091031 ADJUSTABLE FOOT PAD 1

Buy Direct and Save with Grizzly®– Trusted, Proven and a Great Value!
~Since 1983~
ORDER
24 HOURS A DAY!
1-800-523-4777
Visit Our Website Today For
Current Specials!