Grizzly T1238 User manual

For questions or help with this product contact Tech Support at [phone] or [e-mail]
MODEL T1238
MOBILE TOOL TABLE
INSTRUCTIONS
For Models Mfd. Since 10/17
COPYRIGHT © FEBRUARY, 2018 BY GRIZZLY INDUSTRIAL, INC. REVISED JULY, 2018 (TK)
NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE
OR FORM WITHOUT THE WRITTEN APPROVAL OF GRIZZLY INDUSTRIAL, INC.
#TKAB19421 PRINTED IN CHINA V1.07.18
H. Linkage Bar/Pedal ...................................... 1
I. Caster ......................................................... 1
J. Upper Braces (Front & Back) ..................... 2
K. Pedal Assembly .......................................... 1
L. Wheel Assembly ......................................... 1
M. Handle ........................................................ 1
N. Hardware Bag (Not Shown)
—Carriage Bolts M8-1.25 x 12 ................. 30
—Button Hd Cap Screws M8-1.25 x 16 ... 12
—Flat Head Screws M8-1.25 x 25 ............. 4
—Hex Bolts M8-1.25 x 20 .......................... 2
—Hex Bolt M8-1.25 x 70 ............................ 1
—Flange Nuts M8-1.25 ............................ 38
—Lock Nuts M8-1.25 .................................. 3
—Extension Spring .................................... 1
Introduction
The Model T1238 Mobile Tool Table is designed
to provide a stable, mobile platform for mounting
machinery and equipment.
Figure 1. Model T1238 Mobile Tool Table.
Specifications
• Footprint (Length x Width) ..............20" x 23"
• Height ......................................................30"
• Maximum Weight Capacity ............. 300 lbs.
• Approximate Assembly Time .......30 Minutes
Needed for Assembly
• Open-End Wrenches or Sockets 13mm ..... 2
• Hex Wrench 5mm ....................................... 1
Inventory
Description Qty
A. Table Top ................................................... 1
B. Shelf ........................................................... 1
C. Side Panels ................................................ 2
D. Legs w/Foot Pads ....................................... 4
E. Tool Holder ................................................. 1
F. Upper Braces (Left & Right) ....................... 2
G. Lower Braces ............................................. 2
Figure 2. Inventory.
C
B
D
E
F
J
G
H
A
I
K
L
M

-2- T1238 Tool Table (Mfd. Since 10/17)
Assembly
This tool table must be fully assembled before it
can be used. Before beginning the assembly pro-
cess, refer to Needed for Assembly and gather
all listed items.
2. Attach wheel assembly to side assembly
A with (4) M8-1.25 x 16 button head cap
screws. Long linkage should point outward
(see Figure 4) with wheels in the down
position.
To assemble tool table:
1. Build side assembly A by attach-
ing (1) front upper brace to (2) legs with
(4) M8-1.25 x 12 carriage bolts and
(4) M8-1.25 flange nuts (see Figure 3). Use
90° square to make sure legs and supports
are perpendicular (see Figure 3).
Figure 4. Wheel assembly orientation.
4. Attach pedal assembly to side assembly B
built in Step 3 with (4) M8-1.25 x 16 button
head cap screws. Ensure pedal points out-
ward (see Figure 5).
3. Repeat Step 1 in a similar manner to build
side assembly B.
Figure 5. Pedal assembly orientation.
5. Attach caster to pedal assembly with (1)
M8-1.25 x 70 hex bolt and (1) M8-1.25 lock
nut (see Figure 6).
Figure 3. Side assembly A built.
x 4
Legs
90
Degree
Square
x 4
Pedal
Pointing
Outward
x 4
Linkage
Pointing
Outward
Wheel
Down
Upper
Brace
Figure 6. Caster wheel attached to pedal
assembly.
x 1
Pedal
Assembly
Caster

T1238 Tool Table (Mfd. Since 10/17) -3-
6. Attach (2) upper braces and shelf to side
assembly A with (6) M8-1.25 x 12 car-
riage bolts and (6) M8-1.25 flange nuts
(see Figure 7).
7. Attach (2) lower braces to side assembly A
with (2) M8-1.25 x 16 button head cap screws
and (2) M8-1.25 flange nuts (see Figure 7).
10. Turn table assembly upside down.
11. Loosely attach linkage bar to wheel assem-
bly with (1) M8-1.25 x 20 hex bolt and
(1) M8-1.25 lock nut to allow movement.
Connect extension spring to linkage bar and
wheel assembly (see Figure 9).
12. Loosely attach linkage bar to pedal assem-
bly with (1) M8-1.25 x 20 hex bolt and (1)
M8-1.25 lock nut to allow movement (see
Figure 10).
8. Attach side assembly A to side assembly
B with (6) M8-1.25 x 12 carriage bolts and
(6) M8-1.25 flange nuts (see Figure 8).
9. Attach side assembly B to lower braces with
(2) M8-1.25 x 16 button head cap screws and
(2) M8-1.25 flange nuts, as shown in Figure
8.
Figure 8. Side assembly B attached.
x 2
x 6
Side Assembly A
Side Assembly B
x 6
x 2
Figure 9. Linkage and spring installed.
x 1
Extension Spring
Linkage Bar
Wheel Assembly
Figure 10. Linkage bar attached to pedal
assembly.
x 1
Linkage
Bar
Figure 7. Upper/Lower braces and shelf
attached to side assembly A.
x 2
Side Assembly A
Shelf
x 6
Lower
Brace
Upper
Brace

-4- T1238 Tool Table (Mfd. Since 10/17)
18. Ensure all fasteners are firmly tightened and
wheel mechanism operates smoothly.
13. Turn table assembly unit upright. Attach bot-
tom of a side panel to table assembly shelf
with (2) M8-1.25 x 12 carriage bolts and
(2) M8-1.25 flange nuts (see Figure 11).
16. Attach tool holder and top of side panel
with (2) M8-1.25 x 12 carriage bolts and
(2) M8-1.25 flange nuts (see Figure 13).
Figure 14. Table top attached.
x 4
17. Attach table top with (4) M8-1.25 x 25 flat
head screws and (4) M8-1.25 flange nuts
(see Figure 14).
Figure 13. Tool holder attached.
x 2
Tool
Holder
Note: Position side panel so end with
long tab faces up.
15. Repeat Step 13 to attach second side panel
to opposite side of table assembly (see
Figure 11).
14. Attach handle and top of side panel
with (4) M8-1.25 x 12 carriage bolts and
(4) M8-1.25 flange nuts (see Figure 12).
Figure 11. Bottom of side panel attached.
Long Tab
Short Tab
Side
Panel
Shelf
Figure 12. Top of side panel and handle
attached.
x 4
Handle
Side
Panel
x 2
Note: The handle goes on the same side
as the pedal assembly.

T1238 Tool Table (Mfd. Since 10/17) -5-
Moving Tool TableMounting Machines to Table
The Model T1238 Mobile Tool Table is designed
to have machines mounted to it. Mount the
machines to the table top with applicable hard-
ware (not included).
DO NOT mount machines with high centers
of gravity (like table-top drill presses or
mortising machines) on this table. Doing
so could cause the table to tip and fall,
resulting in serious injury or death.
Failure to properly mount machines to
table can cause tipping resulting in injury
property damage.
The strongest mounting option is a "Through
Mount" (see Figure 15) where holes are drilled
all the way through the table, and hex bolts,
washers, and hex nuts are used to secure the
machine in place.
Machine Base
Table Top
Hex
Bolt
Flat Washer
Flat Washer
Lock Washer
Hex Nut
Figure 15. Through mount example.
Depress the lifting pedal to raise the table onto
the wheels. Carefully steer the table to the desired
location, then depress the smaller linkage pedal
to lower the unit onto its feet (see Figure 16).
Any abrupt movement could cause the unit
to tip, resulting in serious personal injury
and property damage.
Figure 16. Moving controls.
Lifting
Pedal
Linkage
Pedal

-6- T1238 Tool Table (Mfd. Since 10/17)
Please Note: We do our best to stock replacement parts whenever possible, but we cannot guarantee that all parts shown here
are available for purchase. Call [phone] or visit our online parts store at www.grizzly.com to check for availability.
1
2
3
8
9
7
5
4
6
10
12
13
14
16
17
18
20 21
26
27
28 29
24 25
19
22 23
4
4
4
4
6
6
32
3
3
3
3
30
31
32
3
3
REF PART # DESCRIPTION REF PART # DESCRIPTION
1 PT1238001 FLAT HD SCR M8-1.25 X 30 18 PT1238018 HANDLE
2 PT1238002 TABLE TOP 19 PT1238019 EXT RETAINING RING 20MM
3 PT1238003 FLANGE NUT M8-1.25 20 PT1238020 FLAT WASHER 20MM
4 PT1238004 CARRIAGE BOLT M8-1.25 X 16 21 PT1238021 LOCK WASHER 20MM
5 PT1238005 STAND LEG 22 PT1238022 SUPPORT FRAME
6 PT1238006 BUTTON HD CAP SCR M8-1.25 X 16 23 PT1238023 REAR ROLLER LEVER
7 PT1238007 FOOT PAD 24 PT1238024 EXTENSION SPRING
8 PT1238008 UPPER BRACE (FRONT & BACK) 25 PT1238025 LINKAGE BAR/PEDAL
9 PT1238009 LOWER BRACE 26 PT1238026 HEX BOLT M8-1.25 X 55
10 PT1238010 TOOL HOLDER 27 PT1238027 RUBBER WHEEL
12 PT1238012 HEX BOLT M8-1.25 X 20 28 PT1238028 CASTER
13 PT1238013 UPPER BRACE (LEFT & RIGHT) 29 PT1238029 HEX BOLT M8-1.25 X 70
14 PT1238014 SIDE PANEL 30 PT1238030 PEDAL ASSEMBLY
16 PT1238016 SHELF 31 PT1238031 EXT RETAINING RING 20MM
17 PT1238017 HANDLE CAP 32 PT1238032 LOCK NUT M8-1.25
BUY PARTS ONLINE AT GRIZZLY.COM!
Scan QR code to visit our Parts Store.
Parts Breakdown & List

T1238 Tool Table (Mfd. Since 10/17) -7-
40
41
42
43
44
45
300 lb. max weight
capacity. DO NOT
exceed. Stand may tip
or collapse, and
crushing injury may
occur.
Safety labels help reduce the risk of serious injury caused by machine hazards. If any label comes
off or becomes unreadable, the owner of this machine MUST replace it in the original location
before resuming operations. For replacements, contact [phone] or www.grizzly.com.
REF PART # DESCRIPTION REF PART # DESCRIPTION
40 PT1238040 NOTICE LABEL 43 PT1238043 CAUTION LABEL
41 PT1238041 GRIZZLY INDUSTRIAL LABEL 44 PT1238044 GRIZZLY.COM LABEL
42 PT1238042 QR CODE LABEL 45 PT1238045 TOUCH-UP PAINT, GLOSSY BLACK
Labels & Cosmetics

-8- T1238 Tool Table (Mfd. Since 10/17)