Grizzly T10157 User manual

COPYRIGHT © OCTOBER, 2008 BY GRIZZLY INDUSTRIAL, INC., REVISED JUNE, 2022 (CS)
WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE
OR FORM WITHOUT THE WRITTEN APPROVAL OF GRIZZLY INDUSTRIAL, INC.
(FOR MODELS MANUFACTURED SINCE 07/19) #TS11313 PRINTED IN CHINA
Figure 1. Model T10157 Oak Workbench.
V4.06.22
***Keep for Future Reference***
Features
• Solid 1
1⁄2" thick oak top with double rows of
bench dog holes for each vise.
• Two storage drawers (with ball bearing slides)
that are 127⁄8" wide x 12
9⁄16" long x 2 13⁄16" deep.
• Sturdy adjustable steel legs with leveling foot
pads.
• Two oak-faced vises with 4" leadscrew travel,
13" wide x 2" thick, and one removable top
plate.
• Four bench dogs and a bench stop bar.
• All wood surfaces finished with durable lac-
quer.
• Overall dimensions: 62" wide x 30" in depth x
32"–39" tall.
• Weight: 110 lbs.
For questions or help with this product contact Tech Support at [phone] or [e-mail]
MODEL T10157
HEAVY-DUTY OAK
WORKBENCH w/STEEL LEGS
INSTRUCTIONS
Wear safety glasses during
the entire setup process!
HEAVY LIFT!
Straining or crushing injury
may occur from improperly
lifting machine or some of
its parts. To reduce this risk,
get help from other people
and use a forklift (or other
lifting equipment) rated for
weight of this machine.

-2- Model T10157 (Mfd. Since 07/19)
Inventory
NOTICE
If you cannot find an item on this list, check
the mounting location on the workbench or
examine the packaging materials carefully.
Some items are pre-installed for shipping
purposes.
Inventory (Figure 2) Qty
A. Front Drawer Panels ................................... 2
B. Right Drawer Panels .................................. 2
C. Bottom Drawer Panels ............................... 2
D. Back Drawer Panels ................................... 2
E. Left Drawer Panels ..................................... 2
F. Workbench Top .......................................... 1
G. Leg Supports .............................................. 2
H. Lower Legs ................................................. 4
I. Upper Legs ................................................. 4
J. Drawer Support Assemblies ....................... 3
K. Leadscrew Plates ....................................... 2
L. Vise Assemblies ......................................... 2
M. Wooden Handles ........................................ 2
N. Bottom Shelf ............................................... 1
O. Bench Stop Bar .......................................... 1
P. Bench Dogs ................................................ 4
The following is a list of items shipped with your
workbench. Before beginning setup, lay these
items out and inventory them.
If any non-proprietary parts are missing (e.g. a
nut or a washer), we will gladly replace them; or
for the sake of expediency, replacements can be
obtained at your local hardware store.
Figure 2. Inventory.
Fasteners (Not Shown) Qty
Q. Wood Dowels ........................................... 22
R. Wood Screws #8 x 11⁄4" ............................ 22
S. Hex Bolts 5⁄16"-18 x 3⁄4" .............................. 20
T. Flat Washers 5⁄16" ...................................... 20
U. Lag Screws 5⁄16" x 1" ................................. 16
V. Wood Screws #10 x 11⁄2" ............................ 9
W. Wood Screws #8 x 1" ............................... 20
AB
C
DE
F
G
H
I
JK
L
M
N
O
P

Model T10157 (Mfd. Since 07/19) -3-
USE THIS CHART TO MATCH UP
HARDWARE DURING THE INVENTORY
AND ASSEMBLY PROCESS.
5mm
5mm
Flat
Head
Cap
Screw
Hardware Recognition Chart

-4- Model T10157 (Mfd. Since 07/19)
Note: Orient sides of drawers so tapered end
of drawer slides (see Figure 4) are facing
back of drawer.
Figure 3. Attaching right and front door panels.
To assemble workbench:
1. Insert (4) wood dowels in front drawer panel,
as shown in Figure 3.
Tip: Use wood glue when installing wood
dowels for extra stability.
2. Press right drawer panel onto wood dowels to
attach it to front drawer panel (see Figure 3).
x 4
Right
Drawer Panel Front
Drawer Panel
4. Install (2) wood dowels in rear holes of right
drawer panel, then press back drawer panel
onto wood dowels (see Figure 6).
Figure 4. Tapered end of drawer slide (right
drawer panel shown).
Tapered End
Back Drawer Panel
x 2
Figure 6. Installing back drawer panel.
Assembly
Items Needed Qty
Wood Glue......................................... As Needed
90° Square ........................................................ 1
Phillips Screwdriver #2 ...................................... 1
Another Person .................................................. 1
Wrench or Socket 1⁄2" ........................................ 1
Open-End Wrench 22mm .................................. 1
3. Slide bottom drawer panel into right and front
panel dadoes (see Figure 5).
Figure 5. Drawer panel bottom inserted into
dadoes.
Bottom
Drawer Panel
5. Install (2) wood dowels in holes of back
drawer panel.

Model T10157 (Mfd. Since 07/19) -5-
6. Press left drawer panel onto wood dowels to
attach it to front and back door panels (see
Figure 7).
Left Drawer Panel
Figure 7. Left drawer panel attached.
Tip: Use 90°square to check and adjust
drawer corners before installing screws in
Steps 7–8.
7. Secure bottom drawer panel to back drawer
panel with (3) #8 x 11⁄4" wood screws (see
Figure 8).
Figure 8. Securing bottom drawer panel to back
drawer panel.
8. Secure left and right drawer panels to back
and front drawer panels with (8) #8 x 11⁄4"
wood screws (see Figure 9).
Figure 9. Securing left and right drawer panels
to front and rear drawer panels.
x 3
Figure 10. Upper and lower leg.
x 8
Upper
Leg
Lower
Leg
9. Repeat Steps 1–8 for second drawer.
10. With assistance from another person, place
workbench top upside down on flat, protected
surface.
11. Slide lower legs into upper legs, then secure
them together with (8) 5⁄16"-18 x 3⁄4" hex bolts
and 5⁄16" flat washers, as shown in Figure 10.
Note: Make sure that completed leg assem-
blies are all same length, which will dictate
height of finished workbench (from 32"–39").
x 8

-6- Model T10157 (Mfd. Since 07/19)
13. Secure leg assemblies to workbench top
with (16) 5⁄16" x 1" lag screws, as shown in
Figure 13.
Figure 13. Leg assemblies installed.
x 16
Leadscrew
Holes
14. Fully tighten all fasteners securing work-
bench top and leg assemblies.
Note: In next step, make sure that drawer
slides on support assemblies are facing cor-
rect way to accept drawers.
15. Use (6) wood dowels to attach drawer sup-
port assemblies to workbench top, as shown
in Figure 14.
16. Secure drawer support assemblies to work-
bench top with (9) #10 x 1
1⁄2" wood screws
(see Figure 14).
Figure 14. Installing drawer support assemblies.
x 6
Drawer Support
Assembly
x 9
Figure 12. Leg assemblies.
Note: In next step, orient legs so bottom shelf
hole in each leg will face inward, as shown in
Figure 11.
x 8
Leg
Support
Leadscrew Holes
Bottom
Shelf Hole
(1 of 4)
Note: In next step, legs must also be ori-
ented so one leadscrew hole faces to side,
and other faces front (see Figure 12). This is
necessary to properly install vise assemblies
in later step.
12. Attach leg supports to leg assemblies with
(8) 5⁄16"-18 x 3⁄4" hex bolts and 5⁄16" flat wash-
ers, and hand-tighten fasteners, as shown in
Figure 12.
Figure 11. Bottom shelf holes facing inward.
Note: In next step, take care to properly ori-
ent leadscrew holes in leg assemblies with
holes in workbench top to accept vise lead-
screws in later step (see Figure 13).

Model T10157 (Mfd. Since 07/19) -7-
17. Secure leadscrew plates (see Figure 15) to
underside of workbench top with (12) #8 x 1"
wood screws.
Figure 15. Installing leadscrew plates.
Leadscrew
Plate
(1 of 2)
x 12
18. With assistance, flip workbench right side up,
move it to its final location, then adjust foot
pads to make workbench level and stable.
19. Attach bottom shelf to legs with (4) 5⁄16"-18 x
3⁄4" hex bolts and 5⁄16" flat washers, as shown
in Figure 16.
Note: You can install shelf with lip facing up
or down.
22. Install drawers, then insert bench stop bar
and bench dogs into workbench top to finish
assembly.
Note: Left and right drawers are different. If
they do not fit, switch their positions.
Figure 16. Bottom shelf installed.
x 4
Bottom Shelf
20. Remove caps from wooden handles, insert
handles through ends of vise assemblies,
then glue caps back on handles, as shown in
Figure 17.
21. Slide each vise assembly into vise faces, as
shown in Figure 17, then secure with (8) #8
x 1" wood screws.
Figure 17. Vise assembly installed.
Wooden Handle
& Cap
Vise Assembly
x 4

-8- Model T10157 (Mfd. Since 07/19)
Parts Breakdown & List
parts
REF PART # DESCRIPTION REF PART # DESCRIPTION
1V2 PT10157001V2 VISE LEADSCREW ASSEMBLY V2.07.19 22 PT10157022 FOOT PAD M14-2.0 X 50
4 PT10157004 WOOD DOWEL M8 X 30 23 PT10157023 BOTTOM SHELF
5 PT10157005 WOOD SCREW #8 X 1-1/4 24 PT10157024 LAG SCREW 5/16-18 X 1
7 PT10157007 DRAWER SLI DE RAIL 25 PT10157025 HEX BOLT 5/16-18 X 3/4
8 PT10157008 WOOD SCREW M4 X 13 27V2 PT10157027V2 WOOD SCREW #8 X 1 V2.07.19
9 PT10157009 WORKBENCH TOP 28V2 PT10157028V2 LEADSCREW PLATE V2.07.19
10 PT10157010 VISE FACE 29 PT10157029 LEG SUPPORT
11V2 PT10157011V2 BENCH STOP BAR (10" OC) V2.01.13 30 PT10157030 FLAT WASHER 5/16
12V2 PT10157012V2 VISE HANDLE ASSEMBLY V2.07.19 31V2 PT10157031V2 ACORN NUT M12 V2.07.19
14 PT10157014 WOOD BENCH DOG 5/8" 32 PT10157032 LEFT DRAWER SUPPORT W/BB SLIDE
15L PT10157015L FRONT LEFT DRAWER PANEL V2.01.10 33 PT10157033 UPPER LEFT LEG W/O LEADSCREW HOLE
15R PT10157015R FRONT RIGHT DRAWER PANEL V2.01.10 33-1 PT10157033-1 UPPER RIGHT LEG W/O LEADSCREW HOLE
16V2 PT10157016V2 DRAWER PANEL LEFT V2.01.10 34V2 PT10157034V2 VISE ROD 15.8MM, M12 V2.07.19
17V2 PT10157017V2 DRAWER PANEL RIGHT V2.01.10 35V2 PT10157035V2 FLAT WASHER 8.5 X 24 X 1.4 V2.07.19
18V2 PT10157018V2 DRAWER PANEL BACK V2.01.10 36V2 PT10157036V2 HEX BOLT M8-1.25 X 12 V2.07.19
19V2 PT10157019V2 DRAWER PANEL BOTTOM V2.01.10 37 PT10157037 WOOD SCREW #10 X 1-1/2
20 PT10157020 UPPER LEG W/SIDE LEADSCREW HOLE 39 PT10157039 RIGHT DRAWER SUPPORT W/ BB SLIDE
20-1 PT10157020-1 UPPER LEG W/FRONT LEADSCREW HOLE 40 PT10157040 CENTER DRAWER SUPPORT W/BB SLI DE
21 PT10157021 LOWER LEG
4
5
7
8
9
10
11V2
14
15L
16V2
17V2
18V2
19V2
21
22
23
24
25
27V2
28V2 30
32
437
39
40
5
27V2
31V2
12V2
34V2
35V2
36V2
33
1V2
27V2
28V2
15R
16V2
17V2
19V2 4
5
7
8
27V2
31V2
12V2
34V2
35V2
36V2
1V2
20
33-1 29
25
30
29
25
30
20-1
18V2
PT10157035V2