GU Electronic HW-REV10 User manual

GENESIS G90 2019
- MODEL : H/W ver 10
- DATE : 2023.03.23

GU Electronic
Index
1. Main Spec
2. Block Diagram
3. Dimension
4. External Appearance
5. Connector Pin Assignment
6. Product Composition
7. DIP S/W Setting
8. Mode Change
9. Install Manual
10. Q & A

GU Electronic
1. Main Spec.
1. Input Spec. (MULTI VIDEO INTERFACE)
- 1 x Digital RGB Input (Navigation System source)
- 1 x HDMI Input (HDMI System source – Audio not support)
- 1 x LVDS Input. (Car Command System)
2. Output Spec.
- 1 x Vertual Analog Touch (Navigation System source)
- 1 x Uart Digital Touch (Navigation System source)
- 1 x USB Touch (DEX System source)
- 1 x LVDS Output (LCD Operation)
3. Power Spec.
- Input Power : 8VDC ~ 24VDC
- Consumption Power : 12Watt, Max
-Storage Temperature : 0 ~75℃
4. Switch Input mode
- Possible to select CAR model while switching mode by DIP S/W
- By button on the Commander in the car via CAN
5. Not support OSD menu

GU Electronic
2. Block Diagram
Scaler
MCU
LVDS
TX
INTERFACE
CAR
COMMAND
SYSTEM
LVDS
CAN
EEPROM
CAN
RECEIVER
LVDS
TX
CAR
TFT-LCD
LVDS
RX
RELAY
LVDS
LVDS
NAVIGATION
SYSTEM
LVDS
RX
HDMI
HDMI
SYSTEM
SAMSUNG
DEX USB-TOUCH

GU Electronic
3. Dimension
* This can change under manufacturer’s circumstance
154mm * 95mm * 23mm
154mm
95mm
23mm

GU Electronic
4. External Appearance
LCD-IN LCD-OUT
LED DIP S/W PROGRAM
R-TOUCH
Digital
RGB
POWER/CAN
USB touch
HDMI
(Audio not support)

GU Electronic
4. External Appearance
LED
DIP S/W PROGRAM
R-TOUCH
Digital
RGB
POWER/CAN
LCD-IN
LCD-OUT
USB touch
HDMI
(Audio not support)

GU Electronic
5. Connector Pin Assignment
*POWER Connect
1. ACC (Red)
2. ACC (Red)
3. Rear-DET (Brown)
4. UART-TXD (Red)
5. CAN-L (Green)
6. CAN-H (Orange)
7. CAN-L (White)
8. CAN-H (Violet)
1 15
2 16
9. N.C
10. N.C
11. ACC-Power (Red)
12. Rear-Power (Red)
13. UART-RXD (Blue)
14. Mode (Green)
15. GND (Black)
16. GND (Black)
*Touch Connect
① Y-
②X-
③Y+
④X+
① ② ③ ④
* Output current
- ACC POWER = +12V, Max 200mA
- REAR POWR = +12V, Max 200mA
* UART Voltage Level
- TXD, RXD = 3.3V Level
*HDMI Connect
Standard pin
(Audio not support)

GU Electronic
6. Product Composition
Interface 1 EA
Power Cable 1 EA
LVDS-IN Cable 1 EA
LVDS-OUT Cable 1 EA

GU Electronic
7. DIP S/W Setting
* ON : DOWN , OFF : UP
PIN FUNCTION DIP S/W Selection
1 NAVI ON : Not Used
OFF : Used
2 HDMI(DEX)
ON : Not Used
OFF : Used
(Audio not support)
3 REAR TYPE ON : OEM
OFF : External
4 CAR type SEL Right Picture
5
Navi Model SEL Down Picture6
7
8
CAR type SEL Right Picture9
10
* DIP S/W Example
GENESIS G90 12.3” (2019~2021)
AVM(SVM)-HDMI
SAMSUNG-DEX
M2C/FINE/KPLAY-2

GU Electronic
8. Mode Change
Mode Change Button
“MENU" button
- Switch mode by pressing for 1 seconds
- Short press to switch OEM

GU Electronic
9. Install Manual
LVDS-OUT Cable
LVDS-IN Cable
AUDIO-UNIT
OEM Audio Unit
Connector A Connector B
M-CAN-H
M-CAN-L
20
7
ACC
GND
1. Installation NAVIKS-carplay Connection
I-CAN-H
I-CAN-L
I-CAN not use
DIP-SW
Mode Change

GU Electronic
9. Install Manual
LVDS-OUT Cable
LVDS-IN Cable
AUDIO-UNIT
OEM Audio Unit
Connector A Connector B
M-CAN-H
M-CAN-L
20
7
ACC
GND
2. Installation KPLAY-2 Connection
I-CAN-H
I-CAN-L
I-CAN not use
DIP-SW
Mode Change

GU Electronic
9. Install Manual
LVDS-OUT Cable
LVDS-IN Cable
AUDIO-UNIT
OEM Audio Unit
Connector A Connector B
M-CAN-H
M-CAN-L
20
7
ACC
GND
3. Installation HDMI Connection (Audio not support)
I-CAN-H
I-CAN-L
I-CAN not use
DIP-SW
Mode Change

GU Electronic
10. Q & A
FAQ
1. Display wrong size of picture
- Check Dip s/w setting
2. Display black screen in OEM mode
- Check connection of LVDS/LCD cable
Caution
1. The device must not be installed in where it interferes driving
(close to brake pedal, steering wheel, airbag etc.)
2. LVDS cable must be connected correctly according to the manual
3. Insulate the end of wire by using electrical tape
4. The installation should be done by expert
5. GU electronic does not take any responsibility for any problem caused by wrong installation
.