GU Electronic MB-NTG-191002 User manual

MB2019_NTG6.0-D
- MODEL : MB-NTG-191002
- DATE : 2020.08.23

GU Electronic
Index
1. Main Spec
2. Block Diagram
3. Dimension
4. External Appearance
5. Connector Pin Assignment
6. Product Composition
7. DIP S/W Setting
8. Mode Change
9. Touch Control
10. OSD(On Screen Display) Control
11. Install Manual
12. Q & A

GU Electronic
1. Main Spec.
1. Input Spec. (MULTI VIDEO INTERFACE)
- 1 x Digital RGB Input (Navigation System source)
- 1 x CVBS Input (Video System source)
- 1 x LVDS Input. (Car Command System)
2. Output Spec.
- 1 x Vertual Analog Touch (Navigation System source)
- 1 x Uart Digital Touch (Navigation System source)
- 1 x LVDS Output (LCD Operation)
3. Power Spec.
- Input Power : 8VDC ~ 24VDC
- Consumption Power : 12Watt, Max
4. Switch Input mode
- Possible to select CAR model while switching mode by DIP S/W
- By button on the Commander in the car via CAN

GU Electronic
2. Block Diagram
Scaler
(PIP)
MCU
LVDS
TX
INTERFACE
CAR
COMMAND
SYSTEM
LVDS
CAN
EEPROM
CAN
RECEIVER
LVDS
TX
CAR
TFT-LCD
LVDS
RX
RELAY
LVDS
LVDS
VIDEO COMPOSITE
NAVIGATION
SYSTEM

GU Electronic
3. Dimension
151mm * 83mm * 24mm
* This can change under manufacturer’s circumstance
151 mm
83mm
24mm

GU Electronic
4. External Appearance
LVDS
IN
VIDEO
Not use.
TOUCH
Digital
RGB
POWER/CAN LVDS
OUT
DIP S/WPROGRAMLED IMAGE

GU Electronic
4. External Appearance
LVDS
IN
DIP S/W PROGRAM
VIDEO
Not use.
TOUCH
Digital
RGB
POWER/CAN
LEDIMAGE
LVDS
OUT

GU Electronic
5. Connector Pin Assignment
*POWER Connect
① ACC(Yellow)
② REAR_POWER (Red)
③ CAN-HIGH (Orange)
④ CAN-LOW (Green)
⑤ CAN-HIGH (Purple)
⑥ CAN-LOW (White)
⑦ REAR_DETECT (Brown)
⑧ GND (Black)
①②③④⑤⑥⑦ ⑧
*NAVI Connect
① R DATA (Red)
② G DATA (Green)
③ B DATA (Blue)
④ SYNC (White)
⑤ GND (Black)
⑥ DMB IR (Green)
⑦ DVD IR (Orange)
①②③④⑤⑥⑦
*Touch Connect
① Y-
② X-
③ Y+
④ X+
① ② ③ ④

GU Electronic
6. Product Composition
Interface 1 EA
Power Cable 1 EA
OSD Board 1 EA
RGB NAVI Cable(7pin) 1 EA
LVDS Cable 1 EA
Touch convertor Cable(KD-900) 1 EA

GU Electronic
6. Product Composition
* CarPlay Set Sales(option) – KPLAY
Interface 1 EA AUX Cable 1 EA
Power Cable 1 EA HDMI Cable 1 EA
Microphone 1 EA
Bluetooth / Wifi Antenna 2EA

GU Electronic
6. Product Composition
CarPlay Main 1 EA AUX Cable 1 EA
Power Cable 1 EA
HDMI Cable 1 EA
* CarPlay(NV17) Set Sales(option)
Microphone 1 EA

GU Electronic
6. Product Composition
* VHQ(Video High Quality Set Sales(option)
Interface 1 EA
Power Cable 1 EA
HDMI Cable 1 EA

GU Electronic
6. Product Composition
* HDMI-TO-DIGITAL Set Sales(option)
Interface 1 EA
Power Cable 1 EA
HDMI Cable 1 EA

GU Electronic
7. DIP S/W Setting
* ON : DOWN , OFF : UP
PIN FUNCTION DIP S/W Selection
1 NAVI ON : Not Used
OFF : Used
2 DVB-T(AV1) ON : Not Used
OFF : Used
3 DVD(AV2) ON : Not Used
OFF : Used
4 N.C
5
CAR type SEL Right Picture
6
7
8
* DIP S/W Example
SPRINTER 12.3”
A180 10.25”
GLE 12.3”
SPRINTER 8.0”
Manual
transmission
SPRINTER 8.0”
Automatic
transmission
A180 7.0”

GU Electronic
8. Mode Change
mode change(1 second)
A-CLASS 12.3”
A-CLASS 8.0”
SPRINTER 12.3”/ 8.0”

GU Electronic
9. Touch Control
Press and hold for more than 11 seconds on
NAVI, DVB-T, DVD screen.
(Note that it only works the first time after
switching screens)
+ Touch according to the shape coordinates
.
OR
OSD menu -> Utility -> Calibration
Touch control - Calibration

GU Electronic
9. Touch Control
DVB-T/DVD Control
Press Icon
DVB-T DVD

GU Electronic
10. OSD(On Screen Display) Control
OSD control
Mode State
First Menu Second Menu Third Menu
MENU Press to display when there is no OSD
screen.
When OSD screen is on, press it to EXIT or
OFF.
SEL Item Selection, Value Selection
UP Item up
Increase selected value
DOWN Item down
Decrease selected value
MENU SEL UP DOWN

GU Electronic
First Menu Second Menu Third Menu Description
Config
NAVI-RGB DIGTAL-INAVI
:Setting the Connected NAVI Model
DVB-T(DMB) ELT_DVBT20
:Setting the Connected DVB-T Model
DVD ELT_980XU Slim
: Setting the Connected DVD Model
RearCam AVM VIDEO
: Setting the Connected RearCam Model
Reset Execute Reset to default value of Config menu
OSD Config
10. OSD(On Screen Display) Control

GU Electronic
OSD - Option Menu
First Menu Second Menu Third Menu Description
Option
NAVI COM
HMS
FINE
:
Set up manufacturer of
woodworking device for UART
Touch use
OFF Do not use features.
RearCam-Type OEM Original Camera
ExtDevice Equipped with external camera
RearCam-Power
ON + 12V continuous supply
AUTO + 12V supply only in Rear
camera mode
OFF + 12V off
RearCam-Det GEAR Detected by CAN
WIRE Detected by Rear-Det Wire
AV Mode ON Function to help when using
the front camera
OFF Do not use features.
FrontCam-Type OEM Original Camera
ExtDevice Equipped with external camera
FrontCam-RcvOpt ON After RearCam shows FrontCam
and returns to previous state
OFF Disable feature
SteeringWheel Btn
ON To use the Streeing button You
must select the “ON" button in
the menu
OFF Do not use features.
10. OSD(On Screen Display) Control