Guardian PitchPro User manual

Product Name: PitchPro
Instruction Manual
Part #: 10540; 10541; 10542; 10543; 10544; 10545
Do not throw away these instructions!
Read and understand these instructions before using equipment!
Introduction 1
Applicable Safety Standards 1
Worker Classifications 1
Safety Information 6 - 7
Product Specific Applications 2
Limitations 2 - 3
Components and Specifications 3
Maintenance, Cleaning, and Storage 5
Inspection 5
Installation and Use 4 - 5
Inspection Log 6
Labels 7

Guardian Fall Protection 6305 S. 231st St., Kent, WA 98032 phone: [phone] fax: [phone] www.guardianfall.com
1
Introduction
Thank you for purchasing a Guardian Fall Protection PitchPro. This manual must be read and understood
in its entirety, and used as part of an employee training program as required by OSHA or any applicable state
agency.
This and any other included instructions must be made available to the user of the equipment. The user must
understand how to safely and effectively use the PitchPro, and all fall safety equipment used in
combination with the PitchPro.
User Information
Date of First Use:
Serial #:
Trainer:
User:
Applicable Safety Standards
When used according to instruction specifications, this product meets or exceeds all applicable OSHA 1926
Subpart M, OSHA 1910, ANSI Z359.18-2017, and ANSI A10.32-2012 standards for fall protection. This product
has been tested in compliance with the requirements of ANSI/ASSE Z359.7. Testing only covers hardware and
does not extend to the anchorage or substrate to which this product is attached. Applicable standards and
regulations depend on the type of work being done, and also might include state-specific regulations. Consult
regulatory agencies for more information on personal fall arrest systems and associated components.

Guardian Fall Protection 6305 S. 231st St., Kent, WA 98032 phone: [phone] fax: [phone] www.guardianfall.com
2
Worker Classifications
!
CAUTION
Understand the following definitions of those who
work near or who may be exposed to fall hazards.
Qualified Person: A person with an accredited degree or certification, and with extensive experience or
sufficient professional standing, who is considered proficient in planning and reviewing the conformity of fall
protection and rescue systems.
Competent Person: A highly trained and experienced person who is ASSIGNED BY THE EMPLOYER to be
responsible for all elements of a fall safety program, including, but not limited to, its regulation, management,
and application. A person who is proficient in identifying existing and predictable fall hazards, and who has
the authority to stop work in order to eliminate hazards.
Authorized Person: A person who is assigned by their employer to work around or be subject to potential or
existing fall hazards.
It is the responsibility of a Qualified or Competent person to supervise the job site and ensure all
applicable safety regulations are complied with.
Product Specific Applications
Personal Fall Arrest: PitchPro may be used to support a MAXIMUM 1 PFAS for use in Fall Arrest
applications. Structure must withstand loads applied in the directions permitted by the system of
at least 5,000 lbs. Maximum free fall is 6‘, or up to 12’ if used in combination with equipment
explicitly certified for such use. Applicable D-ring: Dorsal.
Restraint: PitchPro may be used in Restraint applications. Restraint systems prevent workers
from reaching the leading edge of a fall hazard. Always account for fully deployed length of
lanyard/SRL. Structure must withstand loads applied in the directions permitted by the system
of at least 1,000 lbs. No free fall is permitted. Restraint systems may only be used on surfaces
with slopes up to 4/12 (vertical/horizontal). Applicable D-rings: Dorsal, Chest, Side, Shoulder.
!
WARNING
Use of equipment in unintended applications may result in serious
injury or death. Maximum 1 attachment per connection point.
For all applications: worker weight capacity range
(including all clothing, tools, and equipment) is 130-420 lbs.
Rescue/Confined Space: PitchPro may be used in Rescue/Confined Space applications. Rescue
systems function to safely recover a worker from a confined location or after exposed to a fall.
There are various configurations of Rescue systems depending on the type of rescue. Structure
must withstand loads applied in the directions permitted by the system of at least 3,000 lbs. No
free fall is permitted. Applicable D-rings: Dorsal, Chest, Shoulder.
Work Positioning: PitchPro may be used in Work Positioning applications. Work Positioning
systems allow a worker to be supported and work freely with both hands. Structure must
withstand loads applied in the directions permitted by the system of at least 3,000 lbs. Maximum
allowable free fall is 2’. Applicable D-rings: Side.

Guardian Fall Protection 6305 S. 231st St., Kent, WA 98032 phone: [phone] fax: [phone] www.guardianfall.com
3
Limitations
Fall Clearance: There must be sufficient clearance below the anchorage connector to arrest a fall before the
user strikes the ground or any obstruction. When calculating fall clearance, account for a MINIMUM 2’ safety
factor, free fall, deceleration distance, harness stretch, swing fall, and all other applicable factors.
Diagram shown is an example fall clearance calculation ONLY.
Fall clearance calculation shown based on standing
worker falling directly in-line with anchor point.
Always consider potential swing fall and other
hazards when calculating fall clearance.
*Eliminate Swing Fall whenever
possible! If Swing Fall exists,
always account for additional
fall clearance.
1.5’
2’
12’
5’
Anchor Point
at Foot Level
12’ Free Fall
Lanyard
Anchor Point
Level w/Dorsal D-ring
6’ Free Fall
Lanyard
2’
Swing Falls: Prior to installation or use, make considerations for eliminating or minimizing all swing fall
hazards. Swing falls occur when the anchor is not directly above the location where a fall occurs. Always work
as close to in line with the anchor point as possible. Swing falls significantly increase the likelihood of serious
injury or death in the event of a fall.

Guardian Fall Protection 6305 S. 231st St., Kent, WA 98032 phone: [phone] fax: [phone] www.guardianfall.com
4
Correct Anchorage Positioning:
This chart details allowable working zones required
to reduce risk of swing falls and improper side loading.
ALWAYS adhere to information specified by chart.
Anchor Distance
From
Leading Edge (Y)
Working Distance
Along Roof Edge
(Either Direction) (X)
Working Angle
From
Perpendicular (Ø)
6’
10’
15’
20’
25’
30’
35’
40’
45’
50’
55’
60’
8’
9’ - 9”
11’ - 7”
13’ - 3”
14’ - 6”
16’
17’ - 2”
18’ - 3”
19’ - 4”
19’ - 10”
21’ - 4”
22’ - 3”
53°
45°
38°
33°
30°
28°
26°
24°
23°
21°
21°
21°
For example, if the anchorage connector is 6’ from the leading
edge (Y), the working distance (X) is 8’ in each direction from
the perpendicular, which translates to a 53° working angle.
Ø: Total Working Angle
X: Working Distance
Along Leading Edge
Y: Distance From
Leading Edge
X
Y
ø
X
Leading Edge
Compatibility: When making connections with PitchPro, eliminate all possibility of roll-out. Roll-out occurs
when interference between a hook and the attachment point causes the hook gate to unintentionally open
and release. All connections must be selected and deemed compatible with PitchPro by a Competent
Person. All connector gates must be self-closing and self-locking, and withstand minimum loads of 3,600 lbs.
See the following for examples of compatible/incompatible connections:
Connector
closed and
locked to
D-ring. OK.
Connector
to integral
lanyard.
NO.
Two or more
snap hooks or
carabiners
connected to
each other. NO.
Two connectors
to same
D-ring. NO.
Connector
directly to
horizontal
lifeline. NO.
Connector
directly to
webbing.
NO.
Incompatible
or irregular
application,
which may
increase risk
of roll-out. NO.

Components and Specifications
Guardian Fall Protection 6305 S. 231st St., Kent, WA 98032 phone: [phone] fax: [phone] www.guardianfall.com
5
Type A anchorage connector.
Minimum permitted service temperature: -30° F.
5,000 lb. MBS (minimum breaking strength).
Materials: stainless steel.
Fastener installation holes (qty. 12)
10”
2½
Connection point
Part # Color Description
10541 Brown
PitchPro Anchor - Case Pack (qty. 25)
10542
10543
10544
10545 PitchPro Anchor - Case Pack (qty. 25)
PitchPro Anchor - Single Unit
PitchPro Anchor - Single Unit
PitchPro Anchor - Single Unit
Gray
Black
Brown
Gray
10540 Black
PitchPro Anchor - Case Pack (qty. 25)

Guardian Fall Protection 6305 S. 231st St., Kent, WA 98032 phone: [phone] fax: [phone] www.guardianfall.com
6
Installation and Use
MINIMUM substrate thickness requirements:
• Wood: 3½” (total combined).
• Metal: Installation onto metal sheeting is only permitted if sufficient (minimum 3½“) wood framing member
is present immediately beneath installation location, as determined by jobsite Competent Person. All fasteners
must fully embed into wood.
• Concrete: 6” thick and 2,500 psi.
1. Determine installation location for PitchPro; ensure location is free of debris, rot, decay, cracking, and
hazardous materials. NEVER install on substrate incapable of withstanding minimum loads required by
application.
!
WARNING
NEVER load anchor improperly. Prior to installation, refer to
anchorage positioning chart (pg. 4) to ensure installation
location will satisfy intended work application(s).
Compatible roof pitch:
• 0/12 - vertical/sheer.
• Never install past sheer (such as on underside of beam or slab).
Substrate fastener requirements (do not mix fastener types):
• Wood: (12) 2½” Grip-Rite exterior screws (or equivalent, as determined by jobsite Competent Person) OR
(12) 16d galvanized framing nails.
• Metal: (12) 2½” Grip-Rite exterior screws (or equivalent, as determined by jobsite Competent Person) OR
(12) 16d galvanized framing nails.
• Concrete: (12)
3/16
” x 1¾” concrete screws. Pre-drill all fasteners holes using
5/32
” drill bit.
2. Make considerations for eliminating or
minimizing swing fall hazards.
3. Ensure all fasteners are deemed
compatible by a Competent Person.
4. Place PitchPro at selected installation
location. PitchPro MUST install flush
against substrate. All fasteners MUST be
fully embedded in substrate. May be used
in multiple installation applications. Always
use new fasteners for each new installation.
5. OK for loading in any direction. Over-ridge
and side-loading for Restraint applications only.
6. OK for use in horizontal lifeline (HLL)
applications only when used in combination
with Guardian HLL part # 30800, and only for
connection of a maximum 2 PFAS to HLL.
Over-ridge and
side-loading
applications never
for Fall Arrest.
NO
NO
OK
NO
Ø Ø

Guardian Fall Protection 6305 S. 231st St., Kent, WA 98032 phone: [phone] fax: [phone] www.guardianfall.com
7
NEVER over-torque screws. Excessive torque may cause damage to
screws and result in unsafe installation. OK for use in multiple installation
applications. Always use new fasteners for each new installation.
Removal of anchor from present installation location may cause
warping or damage. NEVER reinstall anchor if it is damaged in
any way, or will not lie flush against applicable substrate.
!
WARNING
Installation:
1. Installation location must be selected and deemed
compatible with PitchPro by a Competent Person.
2. PitchPro must lie flush against substrate. Place
PitchPro at selected installation location and install
all fasteners in accordance with applicable substrate:
Wood install:
- Install (12) specified nails OR screws. All fasteners
must fully embed into substrate. Minimum (8) fasteners
must penetrate fully into truss or support beam.
Metal install:
- PitchPro must never be installed onto standalone
metal substrates. Installation on top of metal sheeting
is only permitted if all conditions of wood installation
can be met.
Concrete install:
- Install (12) specified concrete screws. All fasteners
must fully embed into substrate.
3. Connect complete and compatible PFAS to PitchPro
connection point.
For wood install,
8 fasteners (center
column and either
adjacent column) into
truss/support beam.

Guardian Fall Protection 6305 S. 231st St., Kent, WA 98032 phone: [phone] fax: [phone] www.guardianfall.com
8
Maintenance, Cleaning, and Storage
If PitchPro fails inspection in any way, immediately remove it from service, and contact Guardian to
inquire about its return or repair. Field serviceability testing is not required, and should not be done by the
end user.
Cleaning after use is important for maintaining the safety and longevity of PitchPro. Remove all dirt,
corrosives, and contaminants from PitchPro before and after each use. If PitchPro cannot be
cleaned with plain water, use mild soap and water, then rinse and wipe dry. NEVER clean PitchPro with
corrosive substances.
When not in use, store equipment where it will not be affected by heat, light, excessive moisture, chemicals,
or other degrading elements.
Prior to EACH use, inspect PitchPro for deficiencies, including, but not limited to, corrosion, deformation,
pits, burrs, rough surfaces, sharp edges, cracking, rust, paint buildup, excessive heating, alteration, broken
stitching, fraying, and missing or illegible labels. IMMEDIATELY remove PitchPro from service if defects
or damage are found, or if exposed to forces of fall arrest.
Ensure that applicable work area is free of all damage, including, but not limited to, debris, rot, rust, decay,
cracking, and hazardous materials. Ensure that selected work area will support the application-specific
minimum loads set forth in this instruction manual. Work area MUST be stable.
At least every 12 months, a Competent Person other than the user must inspect PitchPro. Competent
Person inspections MUST be recorded in inspection log in instruction manual and on equipment
inspection grid label. The Competent Person must sign their initials in the box corresponding to the
month and year the inspection took place.
During inspection, consider all applications and hazards PitchPro have been subjected to.
Inspection
Inspection Log
If equipment fails inspection
IMMEDIATELY REMOVE FROM SERVICE.
Date of First Use: __________________.
Product lifetime is indefinite, as long as it
passes pre-use and Competent Person
inspections. User must inspect prior to EACH
use. Competent Person other than user must
complete formal inspection at least every 12
months. Competent Person to inspect and
initial.
This inspection log must be specific to one
PitchPro. Separate inspection logs
must be used for each PitchPro.
All inspection records must be made visible
and available to all users at all times.