Guardian Non-Shock Lanyard User manual

Product Name: Non-Shock Lanyard
Instruction Manual
Part #: 01120, 01121, 01122, 01250, 01251, 01255, 01260, 01261, 01265, 01266, 01270, 01271,
01280
Do not throw away these instructions!
Read and understand these instructions before using equipment!
Introduction 1
Applicable Safety Standards 1
Worker Classifications 1
Safety Information 6
Product Specific Applications 1-2
Limitations 2-3
Components and Specifications 3
Maintenance, Cleaning, and Storage 5
Inspection 5
Installation and Use 4
Inspection Log 5
Labels 7

Introduction
Thank you for purchasing a Guardian Fall
Protection Non-Shock Lanyard. This manual
must be read and understood in its entirety,
and used as part of an employee training
program as required by OSHA or any
applicable state agency.
This and any other included instructions
must be made available to the user of the
equipment. The user must understand how
to safely and effectively use the Non-Shock
Lanyard, and all fall safety equipment used
in combination with the Non-Shock Lanyard.
User Information
Date of First Use:
Serial #:
Trainer:
User:
Applicable Safety Standards
When used according to instruction specifications, this product meets or exceeds all applicable OSHA 1926
Subpart M, OSHA 1910, ANSI Z359.3-2017, and ANSI A10.32-2012 standards for fall protection. Applicable
standards and regulations depend on the type of work being done, and also might include state-specific
regulations. Consult regulatory agencies for more information on personal fall arrest systems and associated
components.
Worker Classifications
!
CAUTION
Understand the following definitions of those who
work near or who may be exposed to fall hazards.
Qualified Person: A person with an accredited degree or certification, and with extensive experience or
sufficient professional standing, who is considered proficient in planning and reviewing the conformity of fall
protection and rescue systems.
Competent Person: A highly trained and experienced person who is ASSIGNED BY THE EMPLOYER to be
responsible for all elements of a fall safety program, including, but not limited to, its regulation, management,
and application. A person who is proficient in identifying existing and predictable fall hazards, and who has
the authority to stop work in order to eliminate hazards.
Authorized Person: A person who is assigned by their employer to work around or be subject to potential or
existing fall hazards.
It is the responsibility of a Qualified or Competent person to supervise the job site and ensure all
applicable safety regulations are complied with.
Guardian Fall Protection 6305 S. 231st St., Kent, WA 98032
1
Product Specific Applications
Personal Fall Arrest: Non-Shock Lanyard may be used to support a MAXIMUM 1 PFAS for use in
Fall Arrest applications ONLY when used in combination with compatible shock absorber
extension. Always account for shock absorber extension length when calculating free fall.
Structure must withstand loads applied in the directions permitted by the system of at least
5,000 lbs. Maximum free fall is 6‘, or up to 12’ if used in combination with equipment explicitly
certified for such use. Applicable D-ring: Dorsal.
!
WARNING
Use of equipment in unintended applications may result in serious
injury or death. Maximum 1 attachment per connection point.

Guardian Fall Protection 6305 S. 231st St., Kent, WA 98032
2
Restraint: Non-Shock Lanyard may be used in Restraint applications. Restraint systems prevent
workers from reaching the leading edge of a fall hazard. Always account for fully deployed length
of lanyard/SRL. Structure must withstand loads applied in the directions permitted by the system
of at least 1,000 lbs. No free fall is permitted. Restraint systems may only be used on surfaces
with slopes up to 4/12 (vertical/horizontal). Applicable D-rings: Dorsal, Chest, Side, Shoulder.
Limitations
Fall Clearance: There must be sufficient
clearance below the anchorage connector
to arrest a fall before the user strikes the
ground or an obstruction. When calculating
fall clearance, account for a MINIMUM 3’
safety factor, deceleration distance, user
height, length of lanyard/SRL, harness
stretch, and all other applicable factors.
Lanyard must be rated for Fall Arrest
to be used in any application in which
a fall could occur.
Diagram shown is an example fall
clearance calculation ONLY.
Swing Falls: Prior to installation or use, make
considerations for eliminating or minimizing
all swing fall hazards. Swing falls occur when
the anchor is not directly above the location
where a fall occurs. Always work as close to in
line with the anchor point as possible. Swing
falls significantly increase the likelihood of
serious injury or death in the event of a fall.
Shock absorber required for applications in
which free fall is possible.
Rescue/Confined Space: Non-Shock Lanyard may be used in Rescue/Confined Space applications.
Rescue systems function to safely recover a worker from a confined location or after exposed to a
fall. There are various configurations of Rescue systems depending on the type of rescue. Structure
must withstand loads applied in the directions permitted by the system of at least 3,000 lbs. No
free fall is permitted. Applicable D-rings: Dorsal, Chest, Shoulder.
Work Positioning: Non-Shock Lanyard may be used in Work Positioning applications. Work
Positioning systems allow a worker to be supported while in suspension and work freely with
both hands. Structure must withstand loads applied in the directions permitted by the system of at
least 3,000 lbs. Maximum allowable free fall is 2’. Applicable D-rings: Side.
For all applications: worker weight capacity range
(including all clothing, tools, and equipment) is 130-310 lbs.
Non-Shock Absorbing Lanyards may only be used in Fall Arrest
applications when used with compatible shock absorber extension.
!
WARNING
Not all Guardian Non-Shock Absorbing Lanyards may be used
in every application type. ALWAYS consider lanyard length, design,
and any other structural components. ALWAYS read and adhere to
product labeling. A Competent Person MUST make a determination
regarding correct lanyard application and compatibility.
!
WARNING
Fall clearance calculation shown based on standing
worker falling directly in-line with anchor point.
Always consider potential swing fall and other
hazards when calculating fall clearance.
*Eliminate Swing Fall whenever
possible! If Swing Fall exists,
always account for additional
fall clearance.

Guardian Fall Protection 6305 S. 231st St., Kent, WA 98032
3
Components and Specifications
Compatibility: When making connections with Non-Shock Lanyard, eliminate all possibility of roll-out. Roll-out
occurs when interference between a hook and the attachment point causes the hook gate to unintentionally
open and release. All connections must be selected and deemed compatible with Non-Shock Lanyard by a
Competent Person. All connector gates must be self-closing and self-locking, and withstand minimum loads of
3,600 lbs. See the following for examples of compatible/incompatible connections:
Materials:
Webbing: Polyester and nylon. 1” width.
Snap Hooks/Rebar Hooks: galvanized steel or aluminum.
Connector
closed and
locked to
D-ring. OK.
Connector
to integral
lanyard.
NO.
Two or more
snap hooks or
carabiners
connected to
each other. NO.
Two connectors
to same
D-ring. NO.
Connector
directly to
horizontal
lifeline. NO.
Connector
directly to
webbing.
NO.
Incompatible
or irregular
application,
which may
increase risk
of roll-out. NO.
Part # Size Description
01280
01250
01260
01265
4’ - 6’
3’
4’
2’
01255
6’
Adjustable Non-Shock Absorbing Lanyard
Non-Shock Absorbing Lanyard - Single Leg
Non-Shock Absorbing Lanyard - Single Leg
Non-Shock Absorbing Lanyard - Single Leg
Non-Shock Absorbing Lanyard - Single Leg
01251
01261
01266
01270
01271
3’
4’ - 6’
6’
Non-Shock Absorbing Lanyard - Single Leg w/Rebar Hook
Non-Shock Absorbing Lanyard - Single Leg w/Rebar Hook
Non-Shock Absorbing Lanyard - Double Leg
Non-Shock Absorbing Lanyard - Single Leg w/Rebar Hook4’
4’ - 6’ Non-Shock Absorbing Lanyard - Double Leg w/Rebar Hooks
01122
01121 18”
18”
Extension Lanyard w/Snap Hook End
Extension Lanyard w/Web Loop End
01120 18” Extension Lanyard w/Snap Hook End - Double Leg

Guardian Fall Protection 6305 S. 231st St., Kent, WA 98032
4
Installation and Use
1. Inspect Guardian Non-Shock Absorbing Lanyards and all PFAS equipment to be used in combination with
Non-Shock Absorbing Lanyards.
2. Ensure that all connectors and all other components of the PFAS are compatible with Guardian Non-Shock
Absorbing Lanyards, and are selected by a Competent Person. The selected safety harness MUST be of proper
size, and MUST be fitted snugly, but still allow for a full range of movement.
3. Make considerations for eliminating or minimizing swing fall hazards.
4. Ensure structure to which the anchorage connector is attached is capable of withstanding a MINIMUM load
relative to the application with which the Non-Shock Absorbing Lanyard is to be used.
5. Attach lanyard snap hook, carabiner, or web loop (as applicable) to compatible harness D-ring. If using in
combination with shock absorber extension, ALWAYS locate the shock absorber end at the applicable harness
D-ring. The shock absorber MUST NEVER be located at the anchorage connector.
6. Attach remaining snap hook or carabiner end of lanyard to compatible anchorage connector. Rebar Hooks
MUST ONLY be connected to structural rebar. Ensure that all connectors are self-closing and self-locking, and
that there is no risk of roll-out.
7. NEVER work with employed harness D-ring positioned above the anchorage connector, unless permitted by
specific application or combination of equipment. A Competent Person must make a determination regarding
the acceptability of working above an anchorage connector.
8. Only use Guardian Lanyards in the fall protection application(s) for which they are designed. Refer to
product labeling, or contact Guardian Fall Protection if unsure of proper application(s).
NEVER use Non-Shock Lanyards for material handling.
!
WARNING

Guardian Fall Protection 6305 S. 231st St., Kent, WA 98032
5
Maintenance, Cleaning, and Storage
If Non-Shock Lanyard fails inspection in any way, immediately remove it from service, and contact Guardian to
inquire about its return or repair.
Cleaning after use is important for maintaining the safety and longevity of Non-Shock Lanyard. Remove all
dirt, corrosives, and contaminants from Non-Shock Lanyard before and after each use. If Non-Shock Lanyard
cannot be cleaned with plain water, use mild soap and water, then rinse and wipe dry. NEVER clean Non-Shock
Lanyard with corrosive substances.
When not in use, store equipment where it will not be affected by heat, light, excessive moisture, chemicals,
or other degrading elements.
Prior to EACH use, inspect Non-Shock Lanyard for deficiencies, including, but not limited to, corrosion,
deformation, pits, burrs, rough surfaces, sharp edges, cracking, rust, paint buildup, excessive heating,
alteration, and missing or illegible labels. IMMEDIATELY remove Non-Shock Lanyard from service if defects or
damage are found, or if exposed to forces of fall arrest.
Ensure that applicable work area is free of all damage, including, but not limited to, debris, rot, rust, decay,
cracking, and hazardous materials. Ensure that selected work area will support the application-specific
minimum loads set forth in this instruction manual. Work area MUST be stable.
At least every 6 months, a Competent Person other than the user must inspect Non-Shock Lanyard.
Competent Person inspections MUST be recorded in inspection log in instruction manual and on
equipment inspection grid label. The Competent Person must sign their initials in the box
corresponding to the month and year the inspection took place.
During inspection, consider all applications and hazards Non-Shock Lanyard have been subjected to.
Inspection
Inspection Log
If equipment fails inspection IMMEDIATELY REMOVE FROM SERVICE.
Date of First Use: __________________.
Product lifetime is indefinite as long as it passes pre-use and Competent Person inspections. User must
inspect prior to EACH use. Competent Person other than user must complete formal inspection at least
every 6 months. Competent Person to inspect and initial.
This inspection log must be specific to one Non-Shock Lanyard. Separate inspection logs must be used
for each Non-Shock Lanyard. All inspection records must be made visible and available to all users at all
times.

Guardian Fall Protection 6305 S. 231st St., Kent, WA 98032
6
Safety Information
Failure to understand and comply with safety regulations may result in
serious injury or death. Regulations included herein are not all-inclusive,
are for reference only, and are not intended to replace a Competent
Person’s judgment or knowledge of federal or state standards.
!
WARNING
Do not alter equipment. Do not misuse equipment.
Workplace conditions, including, but not limited to, flame, corrosive chemicals, electrical shock, sharp objects,
machinery, abrasive substances, weather conditions, and uneven surfaces, must be assessed by a Competent
Person before fall protection equipment is selected.
The analysis of the workplace must anticipate where workers will be performing their duties, the routes they
will take to reach their work, and the potential and existing fall hazards they may be exposed to. Fall
protection equipment must be chosen by a Competent Person. Selections must account for all potential
hazardous workplace conditions. All fall protection equipment should be purchased new and in an unused
condition.
Fall protection systems must be selected and installed under the supervision of a Competent Person, and used
in a compliant manner. Fall protection systems must be designed in a manner compliant with all federal, state,
and safety regulations. Forces applied to anchors must be calculated by a Competent Person.
Unless explicitly stated otherwise, the maximum allowable free fall distance for lanyards must not exceed 6’.
No free fall allowed for non-LE SRLs. Class A SRLs must arrest falls within 24”; Class B SRLs must arrest falls
within 54”.
Harnesses and connectors selected must be compliant with manufacturer’s instructions, and must be of
compatible size and configuration. Snap hooks, carabiners, and other connectors must be selected and applied
in a compatible fashion. All risk of disengagement must be eliminated. All snap hooks and carabiners must be
self-locking and self-closing, and must never be connected to each other.
A pre-planned rescue procedure in the case of a fall is required. The rescue plan must be project-specific. The
rescue plan must allow for employees to rescue themselves, or provide an alternative means for their prompt
rescue. Store rescue equipment in an easily accessible and clearly marked area.
Training of Authorized Persons to correctly erect, disassemble, inspect, maintain, store, and use equipment
must be provided by a Competent Person. Training must include the ability to recognize fall hazards, minimize
the likelihood of fall hazards, and the correct use of personal fall arrest systems.
NEVER use fall protection equipment of any kind to hang, lift, support, or hoist tools or equipment, unless
explicitly certified for such use.
Equipment subjected to forces of fall arrest must immediately be removed from use.
Age, fitness, and health conditions can seriously affect the worker should a fall occur. Consult a doctor if there
is any reason to doubt a user’s ability to withstand and safely absorb fall arrest forces or perform set-up of
equipment. Pregnant women and minors must not use this equipment.
Physical harm may still occur even if fall safety equipment functions correctly. Sustained post-fall suspension
may result in serious injury or death. Use trauma relief straps to reduce the effects of suspension trauma.

Guardian Fall Protection 6305 S. 231st St., Kent, WA 98032
785134 (Rev. H)
Labels
Serial Number : Date of Manufacture: Model Number: Size:
90396 (Rev. F)-2
For use in Restraint or
Work Positioning
applications ONLY.
Non-Shock Absorbing
Lanyard:
Compliant with all
applicable
Z359.3-17, ANSI
A10.32-12, OSHA 1910,
and OSHA 1926 Subpart
M requirements.
Capacity:
130-310lbs max.
(including all
equipment)
Material:
Polyester
DO NOT
REMOVE LABELS
90396 (Rev. F)-1 90396 (Rev. F)-4
Make only safe
and compatible
connections.
For use only with
other OSHA and ANSI
compliant equipment
as part of a personal
fall arrest system.
Remove this lanyard
from service if a fall
has been incurred.
WARNING!
Follow manufacturer’s
instructions provided
with this lanyard at
time of shipment
from manufacturer.
Fully read and
understand
these instructions
before using.
Improper use of this
product could result
in serious injury or
death. Avoid contact
with sharp edges and
abrasive surfaces that
can cut or damage
the webbing or
components.
90396 (Rev. F)-3
User must inspect
before each use.
Competent Person to
inspect and initial at
least every 6 months.
Date of First Use
_____________
Product lifetime is
indefinite, as long as
product passes all
inspection requirements.
Distributed by Engineered Fall Protection | [email protected] | [phone] | www.EngineeredFallProtection.com