Hans Grohe Talis M51 160 2jet 72815007 Manual

ZH 用户手册/组装说明 2
EN Instructions for use / Assembly instructions 3
Lesezeichen
中文 2
English 3
Talis M51 160 2jet
72815007

2
中文
安装 (参见第页4)
安全技巧
装配时为避免挤压和切割受伤，必须戴上手
套。
冷热水管间过大的压力差必须予以平衡。
安装提示
• 安装前必须检查产品是否受到运输损害。安装
后将不认可运输损害或表面损伤。
• 管道和阀门必须根据通用标准进行安装、冲洗
和检查。
• 请遵守当地国家现行的安装规定。
技术参数
工作压强： 最大1MPa
推荐工作压强： 0,1-0,5MPa
测试压强： 1,6MPa
(1MPa=10bar=147PSI)
热水温度： 最大70°C
推荐热水温度： 65°C
热力消毒: 最大70°C/4分钟
该产品专为饮用水设计！
符号说明
请勿使用含有乙酸的硅胶！
调节 (参见第页8)
热水温度调节。如果使用即热式喷头，则不建议
安装热水阀门。
保养 (参见第页12)
单向阀必须在符合国家或当地的法律的情况下按
照EN806-5定期检查(至少一年一次)。
大小 (参见第页9)
流量示意图 (参见第页9)
备用零件 (参见第页14)
清洗 (参见第页10)
操作 (参见第页13)
汉斯格雅建议，清晨或在水流长时间停滞后，前
半升水不作饮用水使用。
问题 原因 补救
龙头出水量小 - 通风机结垢，脏污 - 检查通风机，视需要更换
龙头不灵活 - 阀芯损坏，结垢 - 更换阀芯
龙头滴水 - 阀芯损坏 - 更换阀芯
水从螺纹底座中流出 - 连接软管没有完全旋入基体 - 用手拧紧连接软管
- 连接软管的O形环损坏 - 更换O形环
热水温度过低 - 温度限制器设置错误 - 设置温度限制器

3
English
Assembly (see page 4)
Safety Notes
Gloves should be worn during installation to prevent
crushing and cutting injuries.
The hot and cold supplies must be of equal
pressures.
Installation Instructions
• Prior to installation, inspect the product for transport
damages. After it has been installed, no transport or
surface damage will be honoured.
• The pipes and the fixture must be installed, flushed
and tested as per the applicable standards.
• The plumbing codes applicable in the respective
countries must be observed.
Technical Data
Operating pressure: max. 1 MPa
Recommended operating pressure: 0,1 - 0,5 MPa
Test pressure: 1,6 MPa
(1 MPa = 10 bar = 147 PSI)
Hot water temperature: max. 70°C
Recommended hot water temp.: 65°C
Thermal disinfection: max. 70°C / 4 min
The product is exclusively designed for drinking water!
Symbol description
Do not use silicone containing acetic acid!
Adjustment (see page 8)
To adjust the hot water limiter. Using a hot water limiter
in combination with a continuous flow water heater is
not recommended.
Maintenance (see page 12)
The check valves must be checked regularly according
to EN 806-5 in accordance with national or regional
regulations (at least once a year).
Dimensions (see page 9)
Flow diagram (see page 9)
Spare parts (see page 14)
Cleaning (see page 10)
Operation (see page 13)
Hansgrohe recommends not to use as drinking water
the first half liter of water drawn in the morning or after
a prolonged period of non-use.
Fault Cause Remedy
Insufficient water - Aerator calcified, dirty - Clean aerator, replace as
necessary
Mixer stiff - Cartridge defective, calcified - Exchange cartridge
Mixer dripping - Cartridge defective - Exchange cartridge
Water escaping at the threaded
base
- connection hoses not completely
screwed into basic body
- Tighten connection hoses by hand
- O-ring at the connection hose
defective.
- Exchange O-ring
Hot water temperature too low - Hot water limiter incorrectly set - Set hot water limiter

4
max. 35 mm
max. 60 mm
SW 10 mm
SW 24 mm
(4 Nm)
(3 Nm)
1b
1a 2
3 4
5
150° 110°
6a 6b
Montage

5
150°
24 x 15°
45°
75° 75°
45° 105°
105°
6a
Montage

6
25° 85°
25°85°
110°
55° 55°
6b
24 x 15°
Montage

7
(1 Nm)
> 2 min
910
CLICK
2.
3.
1.
7
80
8
Montage

0,3 MPa
60 °C 10 °C
65
3 4
36°C
38°C
43°C
60°C
55°C
50°C
1 2
1.
2.
SW 3 mm
4 x
1.
2.
SW 3 mm
(5 Nm)
8
Justierung

9
bar
4,5
0,0
0,5
1,0
1,5
2,0
2,5
3,0
3,5
4,0
5,0
0,45
0,00
0,05
0,10
0,15
0,20
0,25
0,30
0,35
0,40
0,50
5,50,55
6,00,60
036912 15 18 21 24 27 30
MPa
00,1 0,2 0,3 0,4 0,5
Q = l/min
Q = l/sec
2
1
8
°
50
152
185
203
350
ca. 500
G1/2
840
max. 60
Ø 33
144
92
83
161
56
86 17
Ø 28
36Ø
121
131
86
144
12
Maße / Durchflussdiagramm

10
•
•
•
•
•
•
•
•
•
•
•
Hansgrohe
Hansgrohe
www.hansgrohe-int.com/guarantee
QuickClean
QuickClean
10
Reinigung
QUICK
CLEAN