Hella SOLANYA Setup guide

Installation instructions and Instructions for use
These instructions must be read
prior to installation
and use!
Over-glass and under-glass awning SOLANYA
Operating guidelines
Installation instructions and Instructions for use
Table of Contents
Preliminary remarks HELLA Over-glass and under-glass awning SOLANYA ......................3
General notes.......................................................................................................................4
CE marking...........................................................................................................................5
Safety instructions ................................................................................................................6
Designated use ..................................................................................................................10
Servicing, maintenance and repair .....................................................................................11
Before installation...............................................................................................................15
Overview: Tools for the installation.....................................................................................16
SOLANYA under-glass overview........................................................................................17
Under-glass mounting brackets overview...........................................................................18
Mounting SOLANYA under-glass .......................................................................................22
SOLANYA over-glass overview..........................................................................................43
Over-glass mounting brackets overview.............................................................................44
Mounting SOLANYA over-glass .........................................................................................46
Malfunctions .......................................................................................................................60
Wiring diagram for motors with ONYX.CONNECTOR........................................................63
Wiring diagram for motors with ONYX.NODE ....................................................................64
Wiring diagram for motors with Somfy io............................................................................65
Wiring diagram for motors with switch operation ................................................................66
Operating instructions and configuration with ONYX..........................................................67
Instructions for use and configuration with Somfy ..............................................................68
Activation guidelines for electric drives...............................................................................69
Commissioning/functional check ........................................................................................70
Removal .............................................................................................................................71
Handing over report (for the fitter) ......................................................................................72
Handing over report (for the user) ......................................................................................73
Installation instructions and Instructions for use
Subject to technical modifications. – Date of issue
January/2023
3
Preliminary remarks HELLA
Over-glass and under-glass awning SOLANYA
With this HELLA product you have opted for a high-quality product with a most up-to-date
technology that can nevertheless be easily installed and operated. In these instructions we
describe the basic installation, commissioning and use.
For authorized specialist staff
For the consumer (user)
The following symbols will assist you with the installation or use and require a safety-
conscious conduct:
Attention!
This symbol indicates instructions that, if disregarded, can put the user in
danger.
Attention!
This symbol indicates instructions that, if disregarded, can potentially result
in damage to the product.
This symbol indicates instructions for use or helpful information.
This symbol requires you to act.
Attention!
This symbol indicates a risk of injury or danger to life due to an electric
shock.
This symbol indicates parts of the product, for which you will find important
information in these installation instructions.
Installation instructions and Instructions for use
4
Subject to technical modifications. – Date of issue
January/2023
General notes
Questions
In case of questions concerning the installation or the use of your product, please consult
your authorized specialist shop.
Spare parts/repairs
Spare parts are available at your HELLA specialist shop. Only spare parts that are
approved by HELLA are allowed to be used.
Warranty/guarantee
Precondition for warranty and guarantee is a correct and regular maintenance of the sun
protection device (at least once a year).
Warranty claims are subject to statutory limitation periods. Service parts are excluded
from the warranty; the same applies for changes in color and changes in characteristics
caused by UV radiation.
Liability
In case of non-observance of the directions and information given in these instructions
and in case of improper operation or unintended use, the manufacturer shall not accept
any warranty claims concerning any damage to the product. In these cases, the liability
for consequential damage to any parts or persons is ruled out as well.
Legal notes
The graphs and texts of these instructions were carefully prepared. We cannot be held
liable for any errors and their potential consequences! Subject to technical modifications
to the product and to these instructions! These instructions include copyrighted
information. All rights reserved! The listed product or brand names are trademarks of the
respective owners.

Installation instructions and Instructions for use
Subject to technical modifications. – Date of issue
January/2023
5
CE marking
The over-glass and under-glass awning SOLANYA by HELLA is in compliance with the
declaration of performance according to the Construction Products Regulation; if the unit is
operated with a motor drive it is additionally in compliance with the Machinery Directive
and the Guideline for Electromagnetic Compatibility; in case of proper use, the awning
corresponds to the basic requirements of the harmonised standard EN 13561. The
respective declarations are deposited with the manufacturers.
The CE identification applies for the delivery status of the product. The product mounted
meets the requirements of the specified standard only, if
during installation the information and instructions given in these instructions as well
as the information and instructions of the manufacturers of the screws have been
observed,
the product is installed with the recommended type and number of fasteners/screws.
No changes, rebuildings or extensions, with the exception of those described in these
instructions, are allowed with this product. The fixed CE-label expires with any change,
rebuilding or extension.
HELLA Sonnen- und Wetterschutztechnik GmbH
A-9913 Abfaltersbach 125
21
LE-AMUM-01-001
EN 13561:2004+A1:2008
Over-glass and under-glass awnings
SOLANYA
Exterior textile sun protection
Wind resistance class 2
Installation instructions and Instructions for use
6
Subject to technical modifications. – Date of issue
January/2023
Safety instructions
These installation instructions refer to prefabricated elements, that (1) for
100% are made from parts, which are defined by us, and (2) which are
made in manufacturing processes, which are defined by us too; in all other
cases we do not provide any guarantee!
The safety instructions as well as the appropriate instructions must be read
carefully before installation and use. In case of non-observance of the
directions and information given in these instructions and in case of
improper installation and operation or unintended use, the manufacturer
shall not accept any warranty claims concerning any damage to the
product. In these cases, the liability for consequential damage to any parts
or persons is ruled out as well.
- Follow the described installation steps and pay attention to
recommendations and notes.
- Keep these instructions in a safe place.
- All installation and removal works, as well as maintenance and repair
works are only allowed to be carried out by authorised and qualified
specialist staff.
- If switching, automatic or radio control devices are used to operate the
units, the information given in the enclosed instructions of the
manufacturer must be observed.
- During operation do not put your hand into or touch movable parts.
- Ensure that clothing or body parts cannot get caught on the unit.
- Observe the regulations for prevention of accidents of the employer's
liability insurance association!
- Before operation check the unit for visible damage. If the unit is
damaged, it should not be used; please consult authorized specialist
staff immediately.
- Risk of injury and accident due to the weight of the product!
- Take safety measures against the danger of squashing, especially when
operating the unit with automatic devices.
- Place the operating switch within sight of the unit, but not near any of the
moving parts.
- Never let children play with the unit.
A sun protection device with electric drive cannot be retracted without
current. We therefore recommend the use of an emergency power
generating unit or a motor with an emergency crank handle, especially in
regions with frequent power failures.
Danger of suffocation!
Ensure that the foil cannot get into the hands of children. Keep the foil in a
safe place.
Installation instructions and Instructions for use
Subject to technical modifications. – Date of issue
January/2023
7
Safety instructions
Attention! Risk of injury or danger to life due to an electric shock!
- Set-up, examination, commissioning and error correction of the unit must
only be performed by authorised or trained expert staff (as per VDE
0100).
- Switch off the current to the connecting lines when working at the unit.
There is danger to life! Take safety precautions against unintentional
switching on!
- Check the electrical wires regularly for damage. Do not use the unit if
any damage is found.
- Our electrically driven units are in accordance with the regulations for
power plants acc. to VDE 0100. We cannot guarantee for the operational
reliability of the unit with non-approved modifications.
- White motor cables are not UV-resistant and must therefore be routed in
empty conduits, cable ducts, or similar.
- The enclosed installation instructions of the electrical devices supplied
must be observed.
Units with motor drive:
The drives used are operated with a voltage of AC 230V/50Hz. Please
check the power supply provided by your utility company before connecting.
Any other voltage can destroy the drives.
Winter operation:
Snow or ice can destroy the unit. The unit may only be operated, if no ice or
snow is lying on the cover.
During this time automatic control devices must be switched to
manual operation.
Installation instructions and Instructions for use
8
Subject to technical modifications. – Date of issue
January/2023
Safety instructions
To prevent damage, please retract your sun protection device with rain,
snowfall or wind.
If automatic control devices are used, adjust the wind controller analogously
to the installed wind resistance class of your sun protection device.
Wind resistance class 0
= wind force <4 (Beaufort),
a performance not required or not measured (according to DIN 13561) or a
product, that does not comply with the requirements of the wind resistance
class 1.
Wind resistance class 1 = wind force 4 (Beaufort),
moderate breeze, moderate wind, moves twigs and thin branches, whirls up
dust and loose paper
Velocity 20 – 27 km/h = 5.5 – 7.4 m/s
Wind resistance class 2 = wind force 5 (Beaufort),
fresh breeze, fresh wind. Smaller deciduous trees start to sway, white
crests are formed on lakes.
Velocity 28 – 37 km/h = 7.5 – 10.4 m/s

Installation instructions and Instructions for use
Subject to technical modifications. – Date of issue
January/2023
9
Safety instructions
If it is necessary to lift the awning via ropes at a higher altitude, the awning
must
- be removed out of the packaging.
- be tied to the pull ropes in such a way, that a slipping out of the awning is
prevented,
- lifted evenly in a horizontal position.
The same applies for the removal of the awning.
It is not allowed that climbing aids are leaned against or fixed to the awning.
They must have a stable base and provide a firm support. Only use
climbing aids with an appropriate carrying capacity.
When working at higher heights, there is risk of falling. Please make sure
that suitable fall protection devices are used.
Awnings are only allowed to be used for the purpose specified in the
instructions for use. Changes, such as extensions or rebuildings, that are
not provided by the manufacturer, are only allowed to be carried out with
the manufacturer’s written approval.
Additional loadings such as objects that are sticked to the awning or cable
tensionings can damage the awning or lead to its crashing, and are
therefore not allowed.
Installation instructions and Instructions for use
10
Subject to technical modifications. – Date of issue
January/2023
Designated use
Sun protection
Thermal protection
Sight screen
Anti-glare blind
Installation instructions and Instructions for use
Subject to technical modifications. – Date of issue
January/2023
11
Servicing, maintenance and repair
With the purchase of your awning you have opted for a high-quality product. To enjoy your
awning for as long as possible, please observe the following information:
Notes to awning covers made of brand acrylic fibres
Brand acrylic fibres, as used for awnings, are materials of the highest quality for awnings.
As they are dope-dyed, these materials show the highest light- and color-fastness. In
addition, their resistance to tearing and resistance to weather, rotting and environmental
effects is unsurpassed. Furthermore, a special textile finishing makes them dirt-, water-, oil-
and grease resistant. The awning cover is heavily tested. At the weaving plant, at the
awning manufacturer and during awning fabrication. As with other covers, differences in
the surface uniformity can also occur with the awning cover. When viewing from the top or
seeing through, you will perhaps find small knots, spots of color, irregular runs of threads
or minimal differences and displacements in the design and rapport, as well as differences
in the color. Please note, that the awning will cause a different color effect in sunlight and
in shade. Naturally, the optical color perception depends on the composition and the
intensity of the emerging light. With increasing depth of color, more light will be absorbed
and less will be reflected. Therefore dark coloured covers let through a small amount of
light, while light colors let a lot of light through. Due to the part-absorption, the composition
of the light shining through will be modified, which results in other color perceptions.
Due to the coloured pigments embedded in the cover and the impregnation, shadings
caused by crinkles or crumple folds can appear, that, especially with light colors, become
visible as strips of shade.
The function, strength or density of the cover will not be reduced by that. Minor differences
in colors between the different cover strips or differences in colors with regard to the
collection of samples cannot be ruled out. The fabrication of several strips also with varying
widths depends on the overall width of the awning.
Ripples in the cover and wrinkling at the seams can arise, because the cover is double
rolled up at the seams.
The highest strain is on the seams of the cover. When rolling up the cover, the seams and
hems lie on top of each other, intensifying the strain. Hems and seams will be pressed flat,
increasing in length. As a result, the lateral seams of the cover can hang down slightly.
Sagging as a result of the own weight of the cover is possible. These specified
phenomenons are not faults in the awning cover, which have been overseen in the testing;
they are unavoidable due to technical, material and physical regularities. They therefore do
not entitle the customer to any refusal or reduction of the purchase price.
Correspondingly, the guidelines for the assessment of ready-made awning covers,
summarized by the German Federal Association "Manufacture of technical textile
registered association" (Bundesverband Konfektion Technischer Textilien e. V.), are also
an integral part of our conditions of sale and delivery.
Installation instructions and Instructions for use
12
Subject to technical modifications. – Date of issue
January/2023
Servicing, maintenance and repair
Cleaning
Cleaning
As a sun protection device fixed outside, the unit can get dirty in the
course of time. This will not reduce the usability of your unit. The powder-
coated parts of your unit will remain presentable for longer, if they are
cleaned regularly with a soft woollen cloth.
Do not use solvents, alcohol (rubbing alcohol) or scouring cleansing
agents!
Leaves or other foreign material lying on the awning cover and in the
awning cassette must be removed immediately. There is danger of
damage or crashing to the awning.
Preventive measures
If you have to draw in the cover in a wet condition, please draw it out for
drying when the next opportunity arises, to prevent marks caused by mould
or mildew.

Installation instructions and Instructions for use
Subject to technical modifications. – Date of issue
January/2023
13
Servicing, maintenance and repair
Maintenance
Maintenance
All inspection and maintenance works must be carried out by a
specialised company from HELLA or a HELLA partner. Regularly check
the electrical wires of motor driven units for damage. Check the
mechanical parts of your unit for visible damage. After exceptional events
such as storm, hail, sleet, maloperation or the like, the unit must be
checked for noticeable damage prior to operating it. If the unit is
damaged, it must not be used; consult authorized specialist staff
immediately. It is recommended to have the unit maintained by specialist
staff on an annual basis. This way wear is detected at an early stage and
damage to the unit is prevented.
Repair works
Repair works
Improper repair works may cause both risk of injury to persons or
damage to the units. All repair works must be carried out by a specialised
company from HELLA or a HELLA partner. Use original HELLA spare
parts only.
Installation instructions and Instructions for use
14
Subject to technical modifications. – Date of issue
January/2023
Operating guidelines
Motor drive
The awning can be extended
or retracted by activating a
switch, a hand-held radio
transmitter or an automatic
device.
End positions:
The lower end position
(awning is extended) is
adjusted in the factory. Please
observe the enclosed
instructions of the
manufacturer of the motor if
any modification is required.
The upper end position
(awning is retracted) is
automatically switched off by
the motor by torque.
Installation instructions and Instructions for use
Subject to technical modifications. – Date of issue
January/2023
15
Before installation
Check the product immediately for possible shipping damage and for
compliance with the delivery receipt.
If parts are missing or damaged, please consult your supplier immediately.
Check the mounting base and ensure that the mounting material to be used
complies with the given conditions to guarantee proper installation. In case
of doubt, please seek advice from a specialist enterprise for fixing
techniques.
The packaging cardboard box should not be exposed to humidity. To
protect it from rain during transport, it should be covered by a foil.
Carry larger units by two persons. Transport and store the units carefully to
prevent injury of persons and damage to the product.
Remove the packaging material carefully. When using a knife, be careful
not to damage the packaging content and to avoid cuts!
Dispose of the packaging material via recycling.
Caution!
A wrong installation can endanger the user seriously. Please strictly
observe the installation instructions. Close off the place of installation.
When working at higher heights, there is risk of falling. Suitable ascent
supports, scaffoldings and fall protection devices are to be used. Please
make sure that the ascent supports stand solidly and provide a firm grip.
Installation instructions and Instructions for use
16
Subject to technical modifications. – Date of issue
January/2023
Overview: Tools for the installation
Battery-powered drill
Depending on the mounting
base (Bit AW 10, AW 20)
Bit extension
Drilling bit
Drill set
acc. to Mounting base
Level Measuring tape Pencil
Screwdriver Spanners
or ratchet
Allen key
Combination pliers or
long-nosed pliers
Side cutter

Installation instructions and Instructions for use
Subject to technical modifications. – Date of issue
January/2023
17
SOLANYA under-glass overview
Legend
Covering cap
Mounting bracket for wall/ceiling installation
Box (2-part)
Guide rail
Tensioner for the cover supporting wire
Mounting brackets for under glass
Front rail
1
2
3
4
5
6
7
1
2
3
4
5
6
7
Installation instructions and Instructions for use
18
Subject to technical modifications. – Date of issue
January/2023
Under-glass mounting brackets overview
Standard brackets
Mounting bracket guide
rail
Mounting angle ceiling
installation
Mounting bracket wall
installation
U1-F30
Type Bracket height
U1-F30 30 mm
DU-140
Type Bracket height
DU-140 140 mm
WU-120
Type Bracket height
WU-120 120 mm
Mounting bracket guide
rail, linkage
Mounting bracket guide
rail, line
U2-F30
Type Bracket height
U2-F30 30 mm
U3-F30
Type Bracket height
U3-F30 30 mm
Installation instructions and Instructions for use
Subject to technical modifications. – Date of issue
January/2023
19
Under-glass mounting brackets overview
Standard brackets
Tensioner for the cover supporting wire Angle bracket for support
wires for the cover,
linkage
TU-112
Type Bracket height
TU-112 112 mm
04210530
Bracket height
93 mm
Installation instructions and Instructions for use
20
Subject to technical modifications. – Date of issue
January/2023
Under-glass mounting brackets overview
Special brackets
Mounting bracket guide
rail
Mounting bracket guide
rail, linkage
Mounting bracket guide
rail, line
U1-F
Type Bracket height
U1-F80 80 mm
U1-F130 130 mm
U2-F
Type Bracket height
U2-F80 80 mm
U2-F130 130 mm
U3-F
Type Bracket height
U3-F80 80 mm
U3-F130 130 mm
Mounting angle ceiling
installation
Tensioner for the cover supporting wire
DU-182
Type Bracket height
DU-182 182 mm
TU-160/TU-210
Type Bracket height
TU-160 160 mm
TU-210 210 mm

Installation instructions and Instructions for use
Subject to technical modifications. – Date of issue
January/2023
21
Under-glass mounting brackets overview
Special brackets
04210512 04210524 04210525
Mounting bracket for guide
rail
30x40 mm
Mounting bracket for guide
rail
50x50 mm
Mounting bracket for guide
rail
80x60 mm
04210526
Mounting bracket for
distance, motor/bearing side
Installation instructions and Instructions for use
22
Subject to technical modifications. – Date of issue
January/2023
Mounting SOLANYA under-glass
Fastening mounting brackets
Please check, if the mounting
brackets supplied comply with
your order.
The mounting angles are
installed staggered to the
second rafter opposite of the
mounting brackets
respectively.
Adjust the mounting angles in
height and depth by using a
chalk line.
Mark the boreholes on the
rafter.
Bore the holes at the specified
positions, and fix the mounting
brackets.
Legend
Mounting angle for ceiling installation
Mounting angle for wall installation
Mounting bracket for guide rail 30 mm
1
2
3
12
140
2
31
Installation instructions and Instructions for use
Subject to technical modifications. – Date of issue
January/2023
23
Mounting SOLANYA under-glass
Fastening mounting brackets
Linked units
Adjust the mounting angles in
height and depth by using a
chalk line.
Legend
Mounting angle for ceiling installation
Mounting bracket for wall installation
Chalk line
1
2
3
1
3
2
3
Installation instructions and Instructions for use
24
Subject to technical modifications. – Date of issue
January/2023
Mounting SOLANYA under-glass
Fastening mounting brackets
Please check if the mounting
brackets supplied for the guide
rails comply with your order.
Loosen the clamping pin by
means of an Allen key (4 mm).
Mark the mounting brackets on
the rafters. Bore the holes at
the specified positions, and fix
the mounting brackets.
Please ensure that the
mounting brackets are in
alignment. If necessary, shift
them laterally.
Legend
Mounting bracket for guide rails 30 mm,
standard design
Mounting bracket for guide rails, linkage
1
2
1
2

Installation instructions and Instructions for use
Subject to technical modifications. – Date of issue
January/2023
25
Mounting SOLANYA under-glass
Fastening mounting brackets
Installation angle bracket for support wires for the cover
Legend
Mounting bracket
Mounting bracket for guide rails
Angle bracket for support wires for
the cover
If the width or projection of the
awning field exceeds 4000
mm, the cover may
increasingly sag. By using an
additional cover supporting
wire, it is possible to avoid this
effect.
As shown above, fix the angle
brackets (3) to the outermost
rafter, in the middle of the
sloping projection of the
awning.
The fixing dimension middle of
the hole of the mounting
brackets (2) is also the fixing
dimension middle of the hole
of the angle brackets (3).
1
2
3
185-300 ≤ 2000 65-300
2
1
3
2
3
Installation instructions and Instructions for use
26
Subject to technical modifications. – Date of issue
January/2023
Mounting SOLANYA under-glass
Fastening mounting brackets
Linked units
Legend
Dimension between axes = ordering dimension (1st unit)
Dimension between axes = ordering dimension (2nd unit)
Mounting angle for ceiling installation
1
2
3
12
3
Installation instructions and Instructions for use
Subject to technical modifications. – Date of issue
January/2023
27
Mounting SOLANYA under-glass
Fastening mounting brackets
Installation in the soffit
Legend
Ordering dimension axis of the guide
rail
Fastening screw
Plain washer
Angle for soffit installation
Sliding block
Mounting bracket
Guide rail
The angular brackets for the
installation in the soffit are
loosely enclosed in the
delivery.
Hold the angular bracket for
the installation in the soffit to
the wall and mark the
boreholes for the fixing.
Provide suitable boreholes for
the fixing.
Fix the angular bracket to the
mounting base by using the
appropriate mounting material,
and adjust it.
Fasten the mounting brackets
to the angular brackets.
Please ensure that the
mounting brackets are in
alignment. If necessary, shift
them laterally.
Please observe the auxiliary
dimension of 22 mm between
the axis of the guide rail and
the outer edge of the box.
1
2
3
4
5
6
7
22
1
2
3
4
5
6
7
Installation instructions and Instructions for use
28
Subject to technical modifications. – Date of issue
January/2023
Mounting SOLANYA under-glass
Installation awning box
Single and linked units
Place the awning on two
prepared trestles.
Unpack the awning (carton,
film).
Now remove the lower
covering profile (1) and put it
aside.
Legend
Lower covering profile
Clamping pins
Linked units
Remove the clamping pins (2)
from the linkage and pull the
linkage apart.
1
2
1
2
2
2

Installation instructions and Instructions for use
Subject to technical modifications. – Date of issue
January/2023
29
Mounting SOLANYA under-glass
Installation awning box
Single and linked units
Position two ladders of the
same height below the
mounting brackets.
Place the awning box on the
top of the ladders. Please
make sure that the awning box
is placed safely and that it
cannot fall down.
Do never work in larger
heights, especially on
balconies, without suitable
fall protection devices!
Lift the awning box evenly with
two persons. Hinge the awning
box completely horizontally
into the mounting brackets.
Legend
Mounting angle for ceiling installation
Box profile
Transport safety device
1
2
3
12
3
Installation instructions and Instructions for use
30
Subject to technical modifications. – Date of issue
January/2023
Mounting SOLANYA under-glass
Installation awning box
Single and linked units
Legend
Mounting bracket
Box profile
Transport safety device
Front rail
Carefully allow the front rail (4)
to move out of the transport
lock (3). To do this, connect
the motor(s) to a test cable
and operate the awning.
Remove the small countersunk
screws from the projecting
parts of the cheeks.
Remove the transport lock (3).
Linked units
Position the ladders below the
mounting brackets of the next
awning.
Also hinge the awning box
carefully into the mounting
brackets, extend the front rail
and unscrew the countersunk
screws.
Remove the transport lock (3).
1
2
3
4
1
2
3
4
Installation instructions and Instructions for use
Subject to technical modifications. – Date of issue
January/2023
31
Mounting SOLANYA under-glass
Installation awning box
Linking the units
Attach the top part of the
box linkage (2) to the right-
hand side part of the left-
hand unit using the provided
fastening screw (1).
Put the outer (4) and the
inner part (5) of the linkage
into the linkage opening of
the right and the left awning
(only with two awnings with
one motor).
Make sure that the slits of
the linkage parts (6) engage
in the inner bolt of the spring
mechanics (7) (only with two
awnings with one motor).
Legend
Countersunk screw M4x20
Box linkage top part
Side part
Outer part of the linkage
Inner part of the linkage
Slit of the linkage part
Inner bolt of the spring mechanics
1
2
3
4
5
6
7
1
2
3
76
4
5
6
7
Installation instructions and Instructions for use
32
Subject to technical modifications. – Date of issue
January/2023
Mounting SOLANYA under-glass
Installation awning box
Linking the units
To link the awnings, telescope
the awnings first and then
push both linking parts
together so that they lie on top
of each other. Turn the roller
tube of the bearing side
(awning without motor) such
that both front rails are
positioned exactly parallel to
one another.
Tighten the threaded pin
accessible at the threaded
linkage (1). Then turn the
awning up to the next threaded
pins and tighten these too.
Screw the two units together.
To do this, insert the screw (2)
through the boreholes in the
middle side parts and tighten
the hexagon nut (3).
Legend
Threaded coupling
Cylinder-head screw 08 x 30
Hexagon nut M8
1
2
3
1
1
3
2

Installation instructions and Instructions for use
Subject to technical modifications. – Date of issue
January/2023
33
Mounting SOLANYA under-glass
Installing the guide rails
As shown in the illustration, fix
the angle bracket for the cover
supporting wire (2) to one of
the centre guide rails (3), in
the middle of the sloping
projection of the awning.
Place cardboards or the like on the floor below the guide rails.
Move both guide rails (3) simultaneously up to half of the arms of the
cheeks (1).
Legend
Arm cheek
Angle bracket for support wires
for the cover, linkage
Guide rail
Crosshead
Fastening screw
1
2
3
4
5
234
5
1
3
Installation instructions and Instructions for use
34
Subject to technical modifications. – Date of issue
January/2023
Mounting SOLANYA under-glass
Installing the guide rails
Legend
Pulley
Guide rail
Countersunk screw M4x6
Insert the runners (1) of the
pins of the front rail into the
provided channel of the guide
rails (2).
Move the guide rail carefully to
the stop.
Screw it together at the points
provided on the inside for the
purpose.
Ensure that the screw heads
are completely countersunk.
Otherwise the pins of the front
rail could get caught on them.
Please make sure, that the
guide rails do not get
scratched.
1
2
3
1
2
3
Installation instructions and Instructions for use
Subject to technical modifications. – Date of issue
January/2023
35
Mounting SOLANYA under-glass
Installation pull cords
- Place the pull cords over the runner in the awning box (1).
- Place the pull cords in the lower slit of the guide rail.
- Completely retract the awning.
- Take the pull cords around the lower deflection roller (5).
- Take the pull cords back in the upper slit of the guide rail.
- Take the pull cord loops (4) over the bolts of the pull cord fixation (3)
(can be found in the accessories).
- Pull the pull cords (approx. 300 mm) and push the pull cord fixation into
the carriages (2) until it is locked in place.
Legend
Runner in the awning box Pull cord loop
Carriage Deflection roller in the crosshead die
Pull cord fixation Carriage plug
1 4
2 5
3 6
1
2
3
4
5
34
6
2
1
Installation instructions and Instructions for use
36
Subject to technical modifications. – Date of issue
January/2023
Mounting SOLANYA under-glass
Installation pull cords
The installation and removal of the pull cords should be performed by two
persons.
Do not twist the pull cords!
In order to unlock the pull cord fixation, remove the small plug (6) from the
carriages (2), put a screwdriver into the lower opening of the carriages and
push it upwards. Close the opening by means of a plug again.
Pull cords are under tension!

Installation instructions and Instructions for use
Subject to technical modifications. – Date of issue
January/2023
37
Mounting SOLANYA under-glass
Installing the guide rails (mounting brackets)
Legend
Threaded pin
Guide rail
Lift both guide rails evenly and
push them into the mounting
brackets already installed.
Tighten the threaded pins (1)
by using an Allen key (4 mm).
1
2
1
2
Installation instructions and Instructions for use
38
Subject to technical modifications. – Date of issue
January/2023
Mounting SOLANYA under-glass
Installation bottom of the awning
- Extend the awning completely.
- Unscrew the screws from the lower covering profile.
- Position two ladders of the same height below the awning box.
- Place the floor profile on the top of the ladders. Please make sure that it
is placed safely and that it cannot fall down.
- Take the lower covering profile (1) and hook it into the cover supporting
yoke (2).
- In doing so, push the cover support clips (4) rearwards.
- Tilt up the bottom and screw it down from below.
- Clip the cover support clips into the groove of the bottom.
- for linkages/combinations, the lower part (5) of the box linkage must still
be mounted.
Legend
Lower covering profile
Cover supporting yoke
Fastening screw
Cover support clip for the lower
covering profile
Bottom part box linkage
1
2
3
4
5
4
2
1
4
2
1
3
4
5
1
1
Installation instructions and Instructions for use
Subject to technical modifications. – Date of issue
January/2023
39
Mounting SOLANYA under-glass
Tensioner for the cover supporting wire
From a width of 4500 mm with
a sloping projection of 4500
mm and with a width from
5500 mm with a sloping
projection of 4000-4500 mm a
support cord tensioning device
for the cover is included in the
delivery.
Push the screws (2) into the
slit of the bracket for the cover
supporting cord already fixed
and tighten the hexagon nuts
(1).
Cut the cover supporting cord
to the required length. (In
theory: ordering width of the
awning minus 73 mm, but
check the length in advance!)
Legend
Hexagon nut
Hexagon head screw
Locking screw
Cover supporting wire
Tensioner for the cover supporting
wire
Wire clamp
Pass the cover supporting wire
(4) through the support wire
tensioning device for the cover
(5) into the wire clamps (6).
Tighten the locking screws (3)
by using an Allen key (2.5
mm).
Evenly turn the support wire
tensioning device for the cover
onto the screws of the bracket
for the cover supporting wire
on the left and right. Turn the
support wire tensioning device
for the cover alternately until
the cover supporting wire is
tensioned tautly.
1
2
3
4
5
6
12
3
4
5
6
4
Installation instructions and Instructions for use
40
Subject to technical modifications. – Date of issue
January/2023
Mounting SOLANYA under-glass
Tensioner for the cover supporting wire
Cover supporting cord with linked units
Legend
Angle bracket for support wires for the cover, linkage
Cover supporting wire
Tensioner for the cover supporting wire
Wire clamp
Locking screw
Pass the cover supporting wire (2) through he bracket for the cover supporting wire in the
centre (1) through the support wire tensioning devices (3) into the wire clamps (4).
Tighten the clamping screws (5) with an Allen key (2.5 mm).
The further installation is carried out analogously to the installation of single units.
1
2
3
4
5
1
2
3
4
5

Installation instructions and Instructions for use
Subject to technical modifications. – Date of issue
January/2023
41
Mounting SOLANYA under-glass
Adjusting the Underglass Awning
Single units
Legend
Diagonal dimension
Width
Measure again the diagonal
(1) and the width (2).
The diagonal dimension as
well as the width dimensions
must be equal.
If the diagonal/width is not
correct, loosen the screws (I, II
+ III) and move the awning to
the correct dimension.
Afterwards, tighten the screws.
1
2
2
1
1
2
I
II
III
I
II
III
III
Installation instructions and Instructions for use
42
Subject to technical modifications. – Date of issue
January/2023
Mounting SOLANYA under-glass
Adjusting the Underglass Awning
Linked units
- Remeasure the diagonal (1) and the widths (2, 3).
- The diagonal dimension as well as the width dimensions must be equal.
- If the dimensions are not correct, please proceed as described above (single units).
11
2
2
3
3
Installation instructions and Instructions for use
Subject to technical modifications. – Date of issue
January/2023
43
SOLANYA over-glass overview
Legend
Covering cap
Box (2-part)
Guide rail
Front rail
Mounting bracket for top glass
Conduit
Spacer plate (for fixing the upper covering profile)
1
2
3
4
5
6
7
1
2
3
4
5
6
7
Installation instructions and Instructions for use
44
Subject to technical modifications. – Date of issue
January/2023
Over-glass mounting brackets overview
Standard brackets
A1-F Standard A2-F Combination /
linkage
A3-F series
Type Bracket
height
A1-F85 85 mm
A1-F100 100 mm
A1-F150 150 mm
A1-F200 200 mm
Type Bracket
height
A2-F85 85 mm
A2-F100 100 mm
A2-F150 150 mm
A2-F200 200 mm
Type Bracket
height
A3-F85 85 mm
A3-F100 100 mm
A3-F150 150 mm
A3-F200 200 mm
A1-FV - 5 mm axle offset Mounting bracket
Type Bracket height
A1-FV85 85 mm
A1-FV100 100 mm
A1-FV150 150 mm
A1-FV200 200 mm
041009E0

Installation instructions and Instructions for use
Subject to technical modifications. – Date of issue
January/2023
45
Over-glass mounting brackets overview
swivelling brackets
A1-S variable A1-SV variable / 10 mm axle offset
Type Bracket height
A1-S115 115-165
A1-S168 168-216
A1-S217 217-267
Type Bracket height
A1-SV115 115-165
A1-SV168 168-216
A1-SV217 217-267
A2-S variable / linkage A3-S variable / line
Type Bracket height
A2-S115 115-165
A2-S168 168-216
A2-S217 217-267
Type Bracket height
A3-S115 115-165
A3-S168 168-216
A3-S217 217-267
Installation instructions and Instructions for use
46
Subject to technical modifications. – Date of issue
January/2023
Mounting SOLANYA over-glass
Installing the guide rails
Arrangement and fixing of the brackets for the guide rails on the conservatory.
Use an Allen key to loosen the
threaded pin (2) and remove the
clamping cones (3).
Legend
Sloping projection
Threaded pin
Clamping cone
Fix the fixing brackets to the conservatory according to the instructions
given for the appropriate mounting material (see installation sets A-E).
Please observe the minimum and maximum dimensions as shown
below. The axial dimension between the left and the right mounting
bracket corresponds with the ordering dimension of the awning (see
delivery note). Differences can be levelled out up to 14 mm by the long
holes in the mounting brackets.
Tighten the screws only to such an extent, that it is still possible to
move the holding devices in the long holes.
If the adjusting range is insufficient, the awning is too broad or too
small; consequently a modification of the awning in the production
facility of the manufacturer of the awning is required. Do never try to
shorten the awning by yourself; in these cases the right to claim under
guarantee expires.
1
2
3
3
2
131
223
151
>=260 / <=300 >=65 / <=300<= 2088
1
77
85 52
Installation instructions and Instructions for use
Subject to technical modifications. – Date of issue
January/2023
47
Mounting SOLANYA over-glass
Installing the guide rails
Arrangement and fixing of the brackets for the guide rails on the conservatory
Single units
Legend
Dimension between axes for
mounting brackets (corresponds to
the ordering dimension in the order)
Dimension between axes 1
combination
Dimension between axes 2
combination
Linked units
1
2
3
1
23
Installation instructions and Instructions for use
48
Subject to technical modifications. – Date of issue
January/2023
Mounting SOLANYA over-glass
Installing the guide rails
Installation set A
Legend
E-Jot screw A2 ø6.3
L = 50(80/90/100)
E-Jot sealing washer
SW 10
Foam tape 3 mm
Installation set B
Legend
SW 13
Washer M8
Hexagon wood screw ø8x80
Foam tape 3 mm
Installation set D
Legend
Universal dowel ø10
Washer M8
SW 13
Hexagon wood screw ø8x80
1
2
3
4
1
2
3
4
1
2
3
4
1
2
3
4
1
2
3
4
1
2
3
4

Installation instructions and Instructions for use
Subject to technical modifications. – Date of issue
January/2023
49
Mounting SOLANYA over-glass
Installing the guide rails
Installation set C (post-and-beam construction)
Legend
Hanger bolt A2
M8 L = 100/130/200
Washer M8 large
Washer M8
Sealing washer for M8
SW 13
Screw nut M8
Installation set C (wood-aluminium construction)
Legend
Hanger bolt A2
M8 L = 100/130/200
Washer M8 large
Washer M8
Sealing washer for M8
SW 13
Screw nut M8
Installation set E
Legend
Threaded rod M8
L = 100/150
Washer M8 large
Washer M8
Sealing washer for M8
SW 13
Screw nut M8
1
2
3
4
5
6
1
2
3
4
5
6
1
2
3
4
5
6
1
2
3
4
5
6
1
2
3
4
5
6
1
2
3
4
5
6
Installation instructions and Instructions for use
50
Subject to technical modifications. – Date of issue
January/2023
Mounting SOLANYA over-glass
Installing the guide rails
Insert the clamping cones (1)
into the groove of the guide
rails (2).
Then insert the clamping
cones (1) into the already
mounted mounting brackets
(3). Let the guide rail
protrude approx. 50 mm
above the centre of the
uppermost guide rail bracket.
Fix the guide rail on the
mounting brackets by
tightening the threaded pin
(4).
Attention:
For units with a conduit, the
conduit bracket must be
mounted before the guide
rails are installed.
(see mounting of
conduit/conduit support)
Legend
Clamping cone
Guide rail
already mounted mounting brackets
Threaded pin (for clamping the guide
rail on the bracket)
1
2
3
4
1
2
~50
1
2
3
4
Installation instructions and Instructions for use
Subject to technical modifications. – Date of issue
January/2023
51
Mounting SOLANYA over-glass
Installation box
Lift the box onto the
conservatory and place it above
the guide rails. Place cardboard
or such under the support points
to avoid damage/scratches.
Extend the front rail (1) approx.
10 cm and then remove the
transport locks (2). To do this,
the lateral countersunk screws
(3) must be unscrewed from the
projecting parts of the side
parts.
For unit linkage, the steps from
section (Linkage of units) must
be carried out before the box is
pushed onto the guide rail.
Now lift the box to the height of
the guide rails and thread the
projecting part of the side parts
(4) and the runners (5) of the
front rail into the guide rail.
Make sure that the runners (5)
and the projecting part (4) are in
the correct position.
Legend
Front rail
Guide rail/Transport lock
Countersunk screws M4 for screw
connection of side part with guide rail
Projecting part of the side part
Guide rollers
1
2
3
4
5
2
1
3
2
4
25
4
1
Installation instructions and Instructions for use
52
Subject to technical modifications. – Date of issue
January/2023
Mounting SOLANYA over-glass
Installation box
Push the box completely
onto the guide rail. To do
this, lift the upper covering
profile (5) by hand so that it
can be pushed over the
spacer plate (6).
Now screw the projecting
parts of the side parts to the
guide rails (1) from the
inside. Use the countersunk
screws (2) for this.
Ensure that the screw heads
are completely countersunk.
Otherwise the runners can
get caught on them.
Then screw the upper
covering profile (5) to the
guide rail (1). Use the
countersunk screws (4) for
this purpose.
Loosen the threaded pins (3)
in the mounting brackets on
both sides and slide the box
together with the guide rails
into the final upper position.
Then tighten the threaded
pins (3) again.
Legend
Guide rail
Countersunk screws M4 x 6 mm
Threaded pin (in the mounting
bracket)
Countersunk screw M4 x 12 mm
Roof profile
Spacer plate
1
2
3
4
5
6
5
6
1
2
45
3

Installation instructions and Instructions for use
Subject to technical modifications. – Date of issue
January/2023
53
Mounting SOLANYA over-glass
Installation box
Linkage of units
Fasten the bottom part of the
box linkage (2) to the right-
hand side part of the left-
hand unit using the fastening
screw (1) supplied.
Insert the outer (4) and the
inner (5) part of the linkage
into the linkage opening of
the right and left awning
(only for two awnings with
one motor).
Make sure that the slots (6)
of the linkage parts mesh
with the inner bolt (7) of the
spring mechanics.
(only for two awnings with
one motor)
Legend
Countersunk screw M4x20
Box linkage bottom part
Side part
outer part of the linkage
inner part of the linkage
Slit in the linkage part
inner bolt of the spring mechanics
1
2
3
4
5
6
7
3
1
2
6
4
5
7
6
7
Installation instructions and Instructions for use
54
Subject to technical modifications. – Date of issue
January/2023
Mounting SOLANYA over-glass
Installation box
Linkage of units
To link the awnings,
telescope the awnings first
and then push both linking
parts together so that they lie
on top of each other. Turn
the roller tube of the bearing
side (awning without motor)
such that both front rails are
positioned exactly parallel to
one another. Tighten the
threaded pin accessible at
the threaded linkage (1).
Then turn the awning up to
the next threaded pins and
tighten these too.
Screw the two units together.
To do this, insert the screw
(2) through the boreholes in
the middle side parts and
tighten the hexagon nut (3).
Then screw the top part of
the box linkage (4) to the
right-hand side part of the
left unit, after the boxes have
been screwed to the guide
rail (see section: Installation
of box)
Legend
Threaded coupling
Screw M8x30
Hexagon nut M8
Box linkage top part
Countersunk screw M4x20
1
2
3
4
5
1
1
2
3
4
5
Installation instructions and Instructions for use
Subject to technical modifications. – Date of issue
January/2023
55
Mounting SOLANYA over-glass
Mounting the guiding tube/guiding tube support
Attach the conduit bracket (1) to the
guide rail (4). To do this, push the
sliding blocks (2) into the groove of
the guide rail and screw the conduit
bracket to the sliding blocks using
the screws (3) supplied.
Make sure that the conduit bracket
has the same distance to the outer
edge of the guide rail for the left and
right guide rails.
Place the conduit (5) between the
guide rails and screw it to the
conduit brackets.
Conduit support:
When the conduit has been moved
to the desired position, align the
supplied conduit support (7) with the
conduit according to the structure of
the conservatory, and mark the
fixing position on the conservatory
as well as on the conduit.
Legend
Conduit bracket
Sliding block
Fillister head screw M8x12
Guide rail
Conduit
Fillister head screw M10x55
Guiding tube support
1
2
3
4
5
6
7
2
1
3
4
=
=
5
6
=
=
7
Installation instructions and Instructions for use
56
Subject to technical modifications. – Date of issue
January/2023
Mounting SOLANYA over-glass
Mounting the guiding tube/guiding tube support
Attach the conduit support
(1) to the marked position on
the conduit (2).
Use the supplied drilling
screws (3) for this purpose.
(the conduit may have to be
removed again for this).
Then screw the base plate of
the conduit support to the
conservatory.
Legend
Conduit bracket
Conduit
Self-drilling screws 3.9x13 mm
1
2
3
1
2
3

Installation instructions and Instructions for use
Subject to technical modifications. – Date of issue
January/2023
57
Mounting SOLANYA over-glass
Installation pull cords
- Place the pull cords over the runner in the awning box (1).
- Place the pull cords in the lower slit of the guide rail.
- Completely retract the awning.
- Take the pull cords around the lower deflection roller (5).
- Take the pull cords back in the upper slit of the guide rail.
- Take the pull cord loops (4) over the bolts of the pull cord fixation (3)
(can be found in the accessories).
- Pull the pull cords (approx. 300 mm) and push the pull cord fixation into
the carriages (2) until it is locked in place.
Legend
Runner in the awning box Pull cord loop
Carriage Deflection roller in the crosshead die
Pull cord fixation Carriage plug
1 4
2 5
3 6
34
6
2
1
4
3
2
5
Installation instructions and Instructions for use
58
Subject to technical modifications. – Date of issue
January/2023
Mounting SOLANYA over-glass
Installation pull cords
The installation and removal of the pull cords should be performed by two
persons.
Do not twist the pull cords!
To release the pull cord fasteners, remove the small plugs (6) from the
carriages (2) and relieve the strain on the pull cords by pulling them in the
direction of the drop profile. Insert a screwdriver into the opening of the
carriages and press them down. The pull cord is now released and can be
carefully lowered. Close the opening by means of a plug again.
The pull cords are under tension.
Installation instructions and Instructions for use
Subject to technical modifications. – Date of issue
January/2023
59
Mounting SOLANYA over-glass
Aligning the unit
Single unit
Measure again the diagonal (1)
and the width (2).
The width dimensions (measured
once at the top and once at the
bottom) must be the same. This
also applies to the two measured
diagonal dimensions.
If the diagonal/width is not correct,
loosen the screws of the mounting
brackets and move the unit to the
correct dimension.
Tighten the screws again
afterwards.
Legend
Diagonal dimension
Width (single unit or element 1)
Width (element 2)
Linked units
Remeasure the diagonals (1) and the widths (2.3, 3).
The diagonal dimension as well as the width dimensions must be equal. If
the dimensions are not correct, please proceed as described above (single
units).
1
2
3
11
2
2
1
1
2
2
3
3
Installation instructions and Instructions for use
60
Subject to technical modifications. – Date of issue
January/2023
Malfunctions
What is the matter, if...
... the front rail moves to the awning box
askew?
The awning(s) was/were not diagonally
aligned during installation.
Solution: Measure the
diagonal as described in
Chapter “Aligning the over-
/under-glass awning” and align
the awning accordingly.
The tension on the right side or guide rail is
too high or too little on the left side or guide
rail.
Solution: Check the tension
as described in Chapter
“Installation of the pull cords”.
The awning cover is sewn askew.
Solution: Place a small fabric
remnant underneath the right
outer seam of the awning
cover. For this purpose it is
necessary to completely
extend the awning. This has
the effect that the awning cover
rolls up slightly thicker and
brings the front rail closer to
the awning box.
The spring mechanics on the left side is
defective.
Solution: Loosen the pull cord
on the left side. Try to turn the
tape pulley. If the tape pulley
cannot be turned at all or very
easily, the spring mechanics is
defective and must be
replaced.

Installation instructions and Instructions for use
Subject to technical modifications. – Date of issue
January/2023
61
Malfunctions
What is the matter, if...
... the front rail moves centrally to the
awning box?
The tension is too high on both sides.
Solution: Check the tension
as described in Chapter
“Installation of the pull cords”. If
necessary, take off one lapping
of the pull cords of the tape
pulleys.
Installation instructions and Instructions for use
62
Subject to technical modifications. – Date of issue
January/2023
Malfunctions
What is the matter, if...
... the cover slacks in the extended condition?
The tension is too low on one or both sides.
Solution: Check the tension as described in Chapter “Installation of the pull
cords”. Place an additional lapping of the pull cords on the tape pulleys if
necessary.
One or both spring mechanics are defective.
Solution: Loosen the pull cords and try to turn the tape pulleys. If one or
both tape pulley(s) cannot be turned at all or very easily, they are defective
and must be replaced.
The end position of the motor is not set correctly. The front rail extends too far.
Solution: Reset the end position of the motor in accordance with the
supplied setting instructions.
From a certain sloping projection and a certain width, a cover supporting wire (bottom
glass) or a conduit (top glass) is provided.
Solution:
Mount the cover supporting wire as described in section "Cover
supporting wire tensioner" or the conduit as described in section "Mounting
the conduit".
Legend
Cover
1
1
Installation instructions and Instructions for use
Subject to technical modifications. – Date of issue
January/2023
63
Wiring diagram for motors with
ONYX.CONNECTOR
Legend
Junction box
ONYX.
CONNECTOR
Motor
Hirschmann
STAK 3
Hirschmann
STAS 3
STAS 3
STAS 3 for power supply
1 Neutral conductor N
2 Phase L
3 Connection 3 not assigned
4 Protective conductor PE
STAK 3
STAK 3 for motor
connection
1 Neutral conductor N
2 Phase UP
3 Phase DOWN
4 Protective conductor PE
For more details on the electrical connections, instructions for use and
programming, please refer to the section “Instructions for use and
configuration with ONYX” or the supplied documents.
1
2
3
5
6
ONYX.CONNECTOR
2
2
3
3
1
1
4
4
PEN
M
~
N
LPE
4
4
1
1
3
3
2
2
PEN
L
1
2
3
5
6
5
6
44
321
123
44
Installation instructions and Instructions for use
64
Subject to technical modifications. – Date of issue
January/2023
Wiring diagram for motors with ONYX.NODE
Legend
Junction box
ONYX.NODE
Button
Motor
For more details on the electrical connections, instructions for use and
programming, please refer to the section “Instructions for use and
configuration with ONYX” or the supplied documents.
1
2
3
4
ONYX.NODE
0+N
NNL L
LOCAL MOTOR
POWER
M
~
N
L
PE
1
2
34

Installation instructions and Instructions for use
Subject to technical modifications. – Date of issue
January/2023
65
Wiring diagram for motors with Somfy io
Legend
Junction box
Hirschmann plug connection
Somfy io motor
Hirschmann STAK 3
Hirschmann STAS 3
For more details concerning the electrical connections, powers, operating
instructions and programming, please refer to the enclosed documents of
the manufacturer or the HELLA installation instructions.
With the radio system Somfy io all receivers must be taught one after
another (order does not matter), i.e. do not connect several receivers to the
network at the same time as the radio system does not support a
simultaneous teaching process of multiple components.
1
2
3
5
6
M
~
N
LPE
4
4
1
1
3
3
2
2
1
2
3
5
6
Installation instructions and Instructions for use
66
Subject to technical modifications. – Date of issue
January/2023
Wiring diagram for motors with switch operation
Legend
Junction box
Switch
Hirschmann plug connection
Motor
Hirschmann STAK 3
Hirschmann STAS 3
For more details concerning the electrical connections, powers, operating
instructions and programming, please refer to the enclosed documents of
the manufacturer or the HELLA installation instructions.
It is essential that switches for the awning drive be electrically and
mechanically locked.
1
2
3
4
5
6
M
~
N
LPE
4
4
1
1
3
3
2
2
1
2
3
4
5
6
Installation instructions and Instructions for use
Subject to technical modifications. – Date of issue
January/2023
67
Operating instructions and configuration with
ONYX
General
Before configuring, download HELLA’s free app ONYX from the App
store/Google Play to your smart phone.
Before you can use the unit with ONYX.CENTER or ONYX.CLICK, it must
be added in the ONYX app. You will find additional information regarding
the configuration in the instructions for ONYX.CENTER / ONYX.CLICK
directly in the ONYX app or in the download area on our homepage
https://www.hella.info.
Precondition:
The unit is already set up and supplied with electricity.
Stand alone configuration with ONYX.CLICK
To configure the unit, you first have to connect to the ONYX.CLICK hand-
held radio transmitter via the ONYX app. The system is configured and
added under “Configure devices” and “+”. All settings for existing sensors
can be made under “ ” and “Advanced setting” of the respective device.
Smart home configuration with ONYX.CENTER
To configure the unit, you simply have to connect to ONYX.CENTER in the
ONYX app. Use “+” to configure and add the installation. All settings for
existing sensors can be made under “Automatic”.
Attention!
When configuring ONYX.CENTER, “Configuration mode” must be active! It
can be found under “Settings”.
Installation instructions and Instructions for use
68
Subject to technical modifications. – Date of issue
January/2023
Instructions for use and configuration with Somfy
Please refer to the enclosed instructions of the manufacturer for the Somfy
unit operating possibilities via control devices.

Installation instructions and Instructions for use
Subject to technical modifications. – Date of issue
January/2023
69
Activation guidelines for electric drives
The motors we use are drives with integrated planetary gear, brakes, limit
stops at the top and at the bottom, and thermo cut-off switches, also not
only a motor, but a complete drive system.
In some respect, the drives do NOT correspond to other household
electrical consumers. Please strictly observe the following notes and safety
instructions.
The construction, checking, commissioning and error-correcting of the
electrical system are only allowed to be carried out by an electrician (acc. to
VDE 0100). In case of improper connection, considerable danger can arise
for the user.
-Follow the wiring diagram precisely!
- We cannot accept responsibility for damage, that can result from
improper installation.
- Never simultaneously activate the drives with an UPWARDS and a
DOWNWARDS signal!
-Keep a break of approx. 0.5 seconds between the UPWARDS and
the DOWNWARDS command (is often neglected with Instabus EIB-
systems).
Drives with mechanical end position adjustment must not be controlled in
parallel.
Radio interference suppression
The drives are provided with a radio interference suppression according to
the current VDE standards and EC Guidelines. If the drives are operated
with other devices, that include interferences, it is the fitter's duty - as part of
the obligation to suppress interference - to ensure that the entire unit
complies with the current regulations.
Operation in wet spaces
The drives are "splash-proof"; if they are operated in wet spaces, the VDE-
guidelines, inter alia VDE 0100/Parts 701, 702, the guidelines of the local
electric supply companies and of the TÜV must be observed and fulfilled.
Both the instructions and notes given in these instructions, as well as
the instructions and notes given in the respective enclosed
instructions of the manufacturers of the drive systems must be
observed.
Installation instructions and Instructions for use
70
Subject to technical modifications. – Date of issue
January/2023
Commissioning/functional check
Extend and retract the unit in and out completely. When extending the unit
for the first time, make sure no one is in the operating radius or standing
below the unit.
Make sure that during the later operation the units can be extended freely
and without blockings. Do not extend the unit, if objects or persons are in
the operating radius of the sun protection unit. Please observe the safety
instructions.
After the first extending check the mounting material and the construction
elements for strength.
Automatic control devices or switches, that are not in the operator's field of
vision, may not be used for test runs of motor driven units.
We recommend the use of a test cable for the provisional operation of the
motor.
Check all settings.
Check all screwed connections for tightness.
The awning is a sun protection device that is only allowed to be used for the
intended use. Wrong use can put the user in danger.
Additional loadings such as objects that are sticked to the awning or cable
tensionings can damage the awning or lead to its crashing, and are
therefore not allowed.
Clean the elements (see maintenance instructions).
Pass these instructions as well as possible instructions of the motor, switch
and control manufacturer on to the user.
Brief the user, whereupon you provide comprehensive information on the
safety and user instructions of the system.
Have the correct design of the system as well as the installation and briefing
with the safety information confirmed in writing (see handover report).
Installation instructions and Instructions for use
Subject to technical modifications. – Date of issue
January/2023
71
Removal
Switch the unit dead and take safety precautions against unintentional
switching on.
The removal is carried out in reverse order to the installation.
Installation instructions and Instructions for use
72
Subject to technical modifications. – Date of issue
January/2023
Handing over report (for the fitter)
Dear Customer,
We are glad that you have opted for a HELLA brand product. Our units are fabricated with
greatest care and many years of experience.
The instructions for use and the installation instructions have been handed over and must
be read before using the product.
An introduction has taken place.
The safety instructions were pointed out.
Your product
Over-glass and under-glass awning SOLANYA
was manufactured in accordance with EN 13561:2004+A1:2008
and was installed professionally and handed over on the
...........................................................................................................................................
Dealer
Name
Place
Postal code
Date
Name
Street
Customer
Place
House number
Signature
Signature
Date
First name

Installation instructions and Instructions for use
Subject to technical modifications. – Date of issue
January/2023
73
Handing over report (for the user)
Dear Customer,
We are glad that you have opted for a HELLA brand product. Our units are fabricated with
greatest care and many years of experience.
The instructions for use and the installation instructions have been handed over and must
be read before using the product.
An introduction has taken place.
The safety instructions were pointed out.
Your product
Over-glass and under-glass awning SOLANYA
was manufactured in accordance with EN 13561:2004+A1:2008
and was installed professionally and handed over on the
...........................................................................................................................................
Dealer
Name
Place
Postal code
Date
Name
Street
Customer
Place
House number
Signature
Signature
Date
First name
Installation instructions and Instructions for use
HELLA Interior Venetian
Blinds
regulate the lighting in a
room very comfortably,
immediately gracing it
with much more
atmosphere.
HELLA Insect screens
and you decide who is
allowed to come in and
who isn't.
HELLA Pleated Blind
folds up very compactly
and protects very well
against the sun and nosey
glances where only little
space is available.
HELLA Outdoor Blinds
serve for the light
regulation, as view
protection, anti-glare blind
and heat protection.
HELLA Front-mounted
Roller Shutter
for more safety and
protection against rain,
wind, heat, the cold, noise,
incident light and nosey
glances, also available for
subsequent installation.
HELLA Vertical awning
With toggle catch
mechanism for a lovely
façade design with perfect
heat and glare protection.
For questions, wishes and ideas:
HELLA Infoline +43/(0)4846/6555-0
HELLA Sonnen- und Wetterschutztechnik GmbH
A-9913 Abfaltersbach, No. 125
Phone: [phone]
Fax: [phone]
e-mail: [e-mail]
Internet: http://www.hella.info