Hella SOLEYA User manual

Installation instructions and Instructions for use
These instructions must be read
prior to installation
and use!
Over-glass and under-glass awning SOLEYA/SOLEYA protect
Operating guidelines
Installation instructions and Instructions for use
Table of Contents
Preliminary remarks HELLA Over-glass and under-glass awning SOLEYA/SOLEYA protect
.............................................................................................................................................3
General notes.......................................................................................................................4
CE Identification SOLEYA....................................................................................................5
CE Identification SOLEYA protect........................................................................................6
Safety instructions ................................................................................................................7
Designated use ..................................................................................................................11
Servicing, maintenance and repair .....................................................................................12
Operating guidelines...........................................................................................................15
Before installation...............................................................................................................16
Overview: Tools for the installation.....................................................................................17
Overview SOLEYA/SOLEYA protect - under-glass............................................................18
Under-glass mounting brackets overview...........................................................................19
Mounting SOLEYA/SOLEYA protect - under-glass ............................................................23
Adjusting the Underglass Awning.......................................................................................47
Overview SOLEYA/SOLEYA protect - over-glass ..............................................................49
Over-glass mounting brackets overview.............................................................................50
Mounting SOLEYA/SOLEYA protect - over-glass ..............................................................52
Aligning the over-glass awning...........................................................................................75
Installation/wiring LED........................................................................................................77
Malfunctions .......................................................................................................................80
Wiring diagram for motors with ONYX.CONNECTOR........................................................83
Wiring diagram for motors with ONYX.NODE ....................................................................84
Wiring diagram for motors with Somfy io............................................................................85
Wiring diagram for motors with switch operation................................................................86
Wiring diagram for LED lighting ONYX/Somfy io................................................................87
Operating instructions and configuration with ONYX..........................................................88
Activation guidelines for electric drives...............................................................................90
Commissioning/functional check ........................................................................................91
Removal .............................................................................................................................92
Handing over report (for the fitter) ......................................................................................93
Handing over report (for the user) ......................................................................................94
Installation instructions and Instructions for use
Subject to technical modifications. – Issue June/2023 3
Preliminary remarks HELLA
Over-glass and under-glass awning
SOLEYA/SOLEYA protect
With this HELLA product you have opted for a high-quality product with a most up-to-date
technology that can nevertheless be easily installed and operated. In these instructions we
describe the basic installation, commissioning and use.
For authorized specialist staff
For the consumer (user)
The following symbols will assist you with the installation or use and require a safety-
conscious conduct:
Attention!
This symbol indicates instructions that, if disregarded, can put the user in
danger.
Attention!
This symbol indicates instructions that, if disregarded, can potentially result
in damage to the product.
This symbol indicates instructions for use or helpful information.
This symbol requires you to act.
Attention!
This symbol indicates a risk of injury or danger to life due to an electric
shock.
This symbol indicates parts of the product, for which you will find important
information in these installation instructions.
Installation instructions and Instructions for use
4 Subject to technical modifications. – Issue June/2023
General notes
Questions
In case of questions concerning the installation or the use of your product, please consult
your authorized specialist shop.
Spare parts/repairs
Spare parts are available at your HELLA specialist shop. Only spare parts that are
approved by HELLA are allowed to be used.
Warranty/guarantee
Precondition for warranty and guarantee is a correct and regular maintenance of the sun
protection device (at least once a year).
Warranty claims are subject to statutory limitation periods. Service parts are excluded
from the warranty; the same applies for changes in color and changes in characteristics
caused by UV radiation.
Liability
In case of non-observance of the directions and information given in these instructions
and in case of improper operation or unintended use, the manufacturer shall not accept
any warranty claims concerning any damage to the product. In these cases, the liability
for consequential damage to any parts or persons is ruled out as well.
Legal notes
The graphs and texts of these instructions were carefully prepared. We cannot be held
liable for any errors and their potential consequences! Subject to technical modifications
to the product and to these instructions! These instructions include copyrighted
information. All rights reserved! The listed product or brand names are trademarks of the
respective owners.

Installation instructions and Instructions for use
Subject to technical modifications. – Issue June/2023 5
CE Identification SOLEYA
The over-glass and under-glass awning SOLEYA by HELLA is in compliance with the
declaration of performance according to the Construction Products Regulation; if the unit is
operated with a motor drive it is additionally in compliance with the Machinery Directive
and the Guideline for Electromagnetic Compatibility; in case of proper use, the awning
corresponds to the basic requirements of the harmonised standard EN 13561. The
respective declarations are deposited with the manufacturers.
The CE identification applies for the delivery status of the product. The product mounted
meets the requirements of the specified standard only, if
during installation the information and instructions given in these instructions as well
as the information and instructions of the manufacturers of the screws have been
observed,
the product is installed with the recommended type and number of fasteners/screws.
No changes, rebuildings or extensions, with the exception of those described in these
instructions, are allowed with this product. The fixed CE-label expires with any change,
rebuilding or extension.
HELLA Sonnen- und Wetterschutztechnik GmbH
A-9913 Abfaltersbach 125
21
LE-AMUM-01-001
EN 13561:2004+A1:2008
Over-glass and under-glass awnings
SOLEYA
Exterior textile sun protection
Wind resistance class 2
Installation instructions and Instructions for use
6 Subject to technical modifications. – Issue June/2023
CE Identification SOLEYA protect
The over-glass and under-glass awning SOLEYA protect (side-seam guided) by HELLA is
in compliance with the declaration of performance according to the Construction Products
Regulation; if the unit is operated with a motor drive it is additionally in compliance with the
Machinery Directive and the Guideline for Electromagnetic Compatibility; in case of proper
use, the awning corresponds to the basic requirements of the harmonised standard EN
13561. The respective declarations are deposited with the manufacturers.
The CE identification applies for the delivery status of the product. The product mounted
meets the requirements of the specified standard only, if
during installation the information and instructions given in these instructions as well
as the information and instructions of the manufacturers of the screws have been
observed,
the product is installed with the recommended type and number of fasteners/screws.
No changes, rebuildings or extensions, with the exception of those described in these
instructions, are allowed with this product. The fixed CE-label expires with any change,
rebuilding or extension.
HELLA Sonnen- und Wetterschutztechnik GmbH
A-9913 Abfaltersbach 125
21
LE-AUZS-01-001
EN 13561:2004+A1:2008
Over-glass and under-glass awnings
SOLEYA protect
Exterior textile sun protection
Wind resistance class 3
Installation instructions and Instructions for use
Subject to technical modifications. – Issue June/2023 7
Safety instructions
These installation instructions refer to prefabricated elements, that (1) for
100% are made from parts, which are defined by us, and (2) which are
made in manufacturing processes, which are defined by us too; in all other
cases we do not provide any guarantee!
The safety instructions as well as the appropriate instructions must be read
carefully before installation and use. In case of non-observance of the
directions and information given in these instructions and in case of
improper installation and operation or unintended use, the manufacturer
shall not accept any warranty claims concerning any damage to the
product. In these cases, the liability for consequential damage to any parts
or persons is ruled out as well.
- Follow the described installation steps and pay attention to
recommendations and notes.
- Keep these instructions in a safe place.
- All installation and removal works, as well as maintenance and repair
works are only allowed to be carried out by authorised and qualified
specialist staff.
- If switching, automatic or radio control devices are used to operate the
units, the information given in the enclosed instructions of the
manufacturer must be observed.
- During operation do not put your hand into or touch movable parts.
- Ensure that clothing or body parts cannot get caught on the unit.
- Observe the regulations for prevention of accidents of the employer's
liability insurance association!
- Before operation check the unit for visible damage. If the unit is
damaged, it should not be used; please consult authorized specialist
staff immediately.
- Risk of injury and accident due to the weight of the product!
- Take safety measures against the danger of squashing, especially when
operating the unit with automatic devices.
- Place the operating switch within sight of the unit, but not near any of the
moving parts.
- Never let children play with the unit.
A sun protection device with electric drive cannot be retracted without
current. We therefore recommend the use of an emergency power
generating unit or a motor with an emergency crank handle, especially in
regions with frequent power failures.
Danger of suffocation!
Ensure that the foil cannot get into the hands of children. Keep the foil in a
safe place.
Installation instructions and Instructions for use
8 Subject to technical modifications. – Issue June/2023
Safety instructions
Attention! Risk of injury or danger to life due to an electric shock!
- Set-up, examination, commissioning and error correction of the unit must
only be performed by authorised or trained expert staff (as per VDE
0100).
- Switch off the current to the connecting lines when working at the unit.
There is danger to life! Take safety precautions against unintentional
switching on!
- Check the electrical wires regularly for damage. Do not use the unit if
any damage is found.
- Our electrically driven units are in accordance with the regulations for
power plants acc. to VDE 0100. We cannot guarantee for the operational
reliability of the unit with non-approved modifications.
- White motor cables are not UV-resistant and must therefore be routed in
empty conduits, cable ducts, or similar.
- The enclosed installation instructions of the electrical devices supplied
must be observed.
Units with motor drive:
The drives used are operated with a voltage of AC 230V/50Hz. Please
check the power supply provided by your utility company before connecting.
Any other voltage can destroy the drives.
Winter operation:
Snow or ice can destroy the unit.
The unit may only be operated, if no ice or snow is lying on the cover.
During this time automatic control devices must be switched to
manual operation.

Installation instructions and Instructions for use
Subject to technical modifications. – Issue June/2023 9
Safety instructions
To prevent damage, please retract your sun protection device with rain,
snowfall or wind.
If automatic control devices are used, adjust the wind controller analogously
to the installed wind resistance class of your sun protection device.
The wind class specifications apply to the structure of the unit. The
prerequisite for this is a suitable mounting base. This means that the wind
class can be downgraded based on the mounting base.
Wind resistance class 0 = wind force <4 (Beaufort),
a performance not required or not measured (according to DIN 13561) or a
product, that does not comply with the requirements of the wind resistance
class 1.
Wind resistance class 1 = wind force 4 (Beaufort),
moderate breeze, moderate wind, moves twigs and thin branches, whirls up
dust and loose paper
Velocity 20 – 27 km/h = 5.5 – 7.4 m/s
Wind resistance class 2 = wind force 5 (Beaufort),
fresh breeze, fresh wind. Smaller deciduous trees start to sway, white
crests are formed on lakes.
Velocity 28 – 37 km/h = 7.5 – 10.4 m/s
Wind resistance class 3 = wind force 6 (Beaufort),
strong wind, strong branches sway, it is difficult to hold an umbrella,
telegraph cables sough in the wind
Velocity 38 – 50 km/h = 10.5 – 13.8 m/s
Installation instructions and Instructions for use
10 Subject to technical modifications. – Issue June/2023
Safety instructions
If it is necessary to lift the awning via ropes at a higher altitude, the awning
must
- be removed out of the packaging.
- be tied to the pull ropes in such a way, that a slipping out of the awning is
prevented,
- lifted evenly in a horizontal position.
The same applies for the removal of the awning.
It is not allowed that climbing aids are leaned against or fixed to the awning.
They must have a stable base and provide a firm support. Only use
climbing aids with an appropriate carrying capacity.
When working at higher heights, there is risk of falling. Please make sure
that suitable fall protection devices are used.
Awnings are only allowed to be used for the purpose specified in the
instructions for use. Changes, such as extensions or rebuildings, that are
not provided by the manufacturer, are only allowed to be carried out with
the manufacturer’s written approval.
Additional loadings such as objects that are sticked to the awning or cable
tensionings can damage the awning or lead to its crashing, and are
therefore not allowed.
Installation instructions and Instructions for use
Subject to technical modifications. – Issue June/2023 11
Designated use
Sun protection
Thermal protection
Sight screen
Anti-glare blind
Installation instructions and Instructions for use
12 Subject to technical modifications. – Issue June/2023
Servicing, maintenance and repair
With the purchase of your awning you have opted for a high-quality product. To enjoy your
awning for as long as possible, please observe the following information:
Notes to awning covers made of brand acrylic fibres
Brand acrylic fibres, as used for awnings, are materials of the highest quality for awnings.
As they are dope-dyed, these materials show the highest light- and color-fastness. In
addition, their resistance to tearing and resistance to weather, rotting and environmental
effects is unsurpassed. Furthermore, a special textile finishing makes them dirt-, water-, oil-
and grease resistant. The awning cover is heavily tested. At the weaving plant, at the
awning manufacturer and during awning fabrication. As with other covers, differences in
the surface uniformity can also occur with the awning cover. When viewing from the top or
seeing through, you will perhaps find small knots, spots of color, irregular runs of threads
or minimal differences and displacements in the design and rapport, as well as differences
in the color. Please note, that the awning will cause a different color effect in sunlight and
in shade. Naturally, the optical color perception depends on the composition and the
intensity of the emerging light. With increasing depth of color, more light will be absorbed
and less will be reflected. Therefore dark coloured covers let through a small amount of
light, while light colors let a lot of light through. Due to the part-absorption, the composition
of the light shining through will be modified, which results in other color perceptions.
Due to the coloured pigments embedded in the cover and the impregnation, shadings
caused by crinkles or crumple folds can appear, that, especially with light colors, become
visible as strips of shade.
The function, strength or density of the cover will not be reduced by that. Minor differences
in colors between the different cover strips or differences in colors with regard to the
collection of samples cannot be ruled out. The fabrication of several strips also with varying
widths depends on the overall width of the awning.
Ripples in the cover and wrinkling at the seams can arise, because the cover is double
rolled up at the seams.
The highest strain is on the seams of the cover. When rolling up the cover, the seams and
hems lie on top of each other, intensifying the strain. Hems and seams will be pressed flat,
increasing in length. As a result, the lateral seams of the cover can hang down slightly.
Sagging as a result of the own weight of the cover is possible. These specified
phenomenons are not faults in the awning cover, which have been overseen in the testing;
they are unavoidable due to technical, material and physical regularities. They therefore do
not entitle the customer to any refusal or reduction of the purchase price.
Correspondingly, the guidelines for the assessment of ready-made awning covers,
summarized by the German Federal Association "Manufacture of technical textile
registered association" (Bundesverband Konfektion Technischer Textilien e. V.), are also
an integral part of our conditions of sale and delivery.

Installation instructions and Instructions for use
Subject to technical modifications. – Issue June/2023 13
Servicing, maintenance and repair
Cleaning
Cleaning
As a sun protection device fixed outside, the unit can get dirty in the
course of time. This will not reduce the usability of your unit. The powder-
coated parts of your unit will remain presentable for longer, if they are
cleaned regularly with a soft woollen cloth.
Do not use solvents, alcohol (rubbing alcohol) or scouring cleansing
agents!
Leaves or other foreign material lying on the awning cover and in the
awning cassette must be removed immediately. There is danger of
damage or crashing to the awning.
Preventive measures
If you have to draw in the cover in a wet condition, please draw it out for
drying when the next opportunity arises, to prevent marks caused by mould
or mildew.
Installation instructions and Instructions for use
14 Subject to technical modifications. – Issue June/2023
Servicing, maintenance and repair
Maintenance
Maintenance
All inspection and maintenance works must be carried out by a
specialised company from HELLA or a HELLA partner. Regularly check
the electrical wires of motor driven units for damage. Check the
mechanical parts of your unit for visible damage. After exceptional events
such as storm, hail, sleet, maloperation or the like, the unit must be
checked for noticeable damage prior to operating it. If the unit is
damaged, it must not be used; consult authorized specialist staff
immediately. It is recommended to have the unit maintained by specialist
staff on an annual basis. This way wear is detected at an early stage and
damage to the unit is prevented.
An unintentional switching on of electrically driven awnings is possible.
Make sure, that the awning is switched dead during cleaning or
maintenance work (e.g. building cleaner).
The automatic control device must be switched dead when working in the
operating range of the awning. There is danger of squashing and danger
of fall hazards.
In addition, it has to be ensured, that an unintentional manual operation
of the awning is prevented. This may be done by disconnecting the
power supply or by unplugging the plug-in coupling from the motor.
If the awning is operated manually, the operating crank handle must be
hooked out and kept in a safe place.
Repair works
Repair works
Improper repair works may cause both risk of injury to persons or
damage to the units. All repair works must be carried out by a specialised
company from HELLA or a HELLA partner. Use original HELLA spare
parts only.
Installation instructions and Instructions for use
Subject to technical modifications. – Issue June/2023 15
Operating guidelines
Motor drive
The awning can be extended
or retracted by activating a
switch, a hand-held radio
transmitter or an automatic
device.
End positions:
The lower end position
(awning is extended) is
adjusted in the factory. Please
observe the enclosed
instructions of the
manufacturer of the motor if
any modification is required.
The upper end position
(awning is retracted) is
automatically switched off by
the motor by torque.
Installation instructions and Instructions for use
16 Subject to technical modifications. – Issue June/2023
Before installation
Check the product immediately for possible shipping damage and for
compliance with the delivery receipt.
If parts are missing or damaged, please consult your supplier immediately.
Check the mounting base and ensure that the mounting material to be used
complies with the given conditions to guarantee proper installation. In case
of doubt, please seek advice from a specialist enterprise for fixing
techniques.
The packaging cardboard box should not be exposed to humidity. To
protect it from rain during transport, it should be covered by a foil.
Carry larger units by two persons. Transport and store the units carefully to
prevent injury of persons and damage to the product.
Remove the packaging material carefully. When using a knife, be careful
not to damage the packaging content and to avoid cuts!
Dispose of the packaging material via recycling.
Caution!
A wrong installation can endanger the user seriously. Please strictly
observe the installation instructions. Close off the place of installation.
When working at higher heights, there is risk of falling. Suitable ascent
supports, scaffoldings and fall protection devices are to be used. Please
make sure that the ascent supports stand solidly and provide a firm grip.

Installation instructions and Instructions for use
Subject to technical modifications. – Issue June/2023 17
Overview: Tools for the installation
Battery-powered drill
Depending on the mounting
base (Bit AW 10, AW 20)
Bit extension
Drilling bit
Drill set
acc. to Mounting base
Level Measuring tape Pencil
Screwdriver Spanners
or ratchet
Allen key
Combination pliers or
long-nosed pliers
Side cutter
Installation instructions and Instructions for use
18 Subject to technical modifications. – Issue June/2023
Overview SOLEYA/SOLEYA protect - under-glass
Legend
Covering cap
Mounting bracket for wall/ceiling installation
Box (3-part)
Guide rail
Tensioner for the cover supporting wire
Mounting bracket for guide rail
Front rail
1
2
3
4
5
6
7
1
23
4
5
6
7
Installation instructions and Instructions for use
Subject to technical modifications. – Issue June/2023 19
Under-glass mounting brackets overview
Standard brackets
Mounting bracket guide
rail
Mounting angle ceiling
installation
Mounting bracket wall
installation
U1-F30
Type Bracket height
U1-F30 30 mm
DU-157
Type Bracket height
DU-157 157 mm
WU-120
Type Bracket height
WU-120 120 mm
Mounting bracket guide
rail, linkage
Mounting bracket guide
rail, line
U2-F30
Type Bracket height
U2-F30 30 mm
U4-F30
Type Bracket height
U4-F30 30 mm
Installation instructions and Instructions for use
20 Subject to technical modifications. – Issue June/2023
Under-glass mounting brackets overview
Standard brackets
Tensioner for the cover supporting wire Angle bracket for support
wires for the cover,
linkage
TU-135
Type Bracket height
TU-135 135 mm
04170514
Bracket height
110 mm

Installation instructions and Instructions for use
Subject to technical modifications. – Issue June/2023 21
Under-glass mounting brackets overview
Special brackets
Mounting bracket guide
rail
Mounting bracket guide
rail, linkage
Mounting bracket guide
rail, line
U1-F
Type Bracket height
U1-F80 80 mm
U1-F130 130 mm
U2-F
Type Bracket height
U2-F80 80 mm
U2-F130 130 mm
U4-F
Type Bracket height
U4-F80 80 mm
U4-F130 130 mm
Mounting angle ceiling
installation
Tensioner for the cover supporting wire
DU-200
Type Bracket height
DU-200 200 mm
Type Bracket height
TU-185 185 mm
TU-235 235 mm
Installation instructions and Instructions for use
22 Subject to technical modifications. – Issue June/2023
Under-glass mounting brackets overview
Special brackets
04210512 04210524 04210525
Mounting bracket for guide
rail
30x40 mm
Mounting bracket for guide
rail
50x50 mm
Mounting bracket for guide
rail
80x60 mm
04210526
Mounting bracket for
distance, motor/bearing side
Installation instructions and Instructions for use
Subject to technical modifications. – Issue June/2023 23
Mounting SOLEYA/SOLEYA protect - under-glass
Fastening mounting brackets
Please check, if the mounting
brackets supplied comply with
your order.
The mounting angles are
installed staggered to the
second rafter opposite of the
mounting brackets
respectively.
Adjust the mounting angles in
height and depth by using a
chalk line.
Mark the boreholes on the
rafter.
Bore the holes at the specified
positions, and fix the mounting
brackets.
Legend
Mounting angle for ceiling installation
Mounting angle for wall installation
Mounting bracket for guide rail 30 mm
1
2
3
12
157
1 2
3
Installation instructions and Instructions for use
24 Subject to technical modifications. – Issue June/2023
Mounting SOLEYA/SOLEYA protect - under-glass
Fastening mounting brackets
Linked units
Adjust the mounting angles in
height and depth by using a
chalk line.
Legend
Mounting angle for ceiling installation
Mounting bracket for wall installation
Chalk line
1
2
3
1
3
2
3

Installation instructions and Instructions for use
Subject to technical modifications. – Issue June/2023 25
Mounting SOLEYA/SOLEYA protect - under-glass
Fastening mounting brackets
Please check if the mounting
brackets supplied for the guide
rails comply with your order.
Loosen the clamping pin by
means of an Allen key (4 mm).
Mark the mounting brackets on
the rafters. Bore the holes at
the specified positions, and fix
the mounting brackets.
Please ensure that the
mounting brackets are in
alignment. If necessary, shift
them laterally.
Legend
Mounting bracket for guide rails 30 mm,
standard design
Mounting bracket for guide rails, linkage
1
2
1
2
Installation instructions and Instructions for use
26 Subject to technical modifications. – Issue June/2023
Mounting SOLEYA/SOLEYA protect - under-glass
Fastening mounting brackets
Installation angle bracket for support wires for the cover
Legend
Mounting angle for ceiling
installation
Mounting bracket for guide rail,
under-glass
Angle bracket for support wires for
the cover
If the width or projection of the
awning field exceeds 4000
mm, the cover may
increasingly sag. By using an
additional cover supporting
wire, it is possible to avoid this
effect.
As shown above, fix the angle
brackets (3) to the outermost
rafter, in the middle of the
sloping projection of the
awning.
The fixing dimension middle of
the hole of the mounting
brackets (2) is also the fixing
dimension middle of the hole
of the angle brackets (3).
1
2
3
350 ≤ 2000 80-300
1
23
2
3
Installation instructions and Instructions for use
Subject to technical modifications. – Issue June/2023 27
Mounting SOLEYA/SOLEYA protect - under-glass
Fastening mounting brackets
Linked units
Legend
Dimension between axes = ordering dimension (1st unit)
Dimension between axes = ordering dimension (2nd unit)
Mounting angle for ceiling installation
1
2
3
12
3
Installation instructions and Instructions for use
28 Subject to technical modifications. – Issue June/2023
Mounting SOLEYA/SOLEYA protect - under-glass
Fastening mounting brackets
Installation in the soffit
Legend
Ordering dimension axis of the guide
rail
Angular bracket for installation in the
soffit, offset 30 mm (60 mm)
Mounting bracket for guide rail,
under-glass
Guide rail
The angular brackets for the
installation in the soffit are
loosely enclosed in the
delivery.
Hold the angular bracket for
the installation in the soffit to
the wall and mark the
boreholes for the fixing.
Provide suitable boreholes for
the fixing.
Fix the angular bracket to the
mounting base by using the
appropriate mounting material,
and adjust it.
Fasten the mounting brackets
to the angular brackets.
Please ensure that the
mounting brackets are in
alignment. If necessary, shift
them laterally.
Please observe the offset
between the axis of the guide
rail and the outer edge of the
angle of 30 mm or 60 mm.
1
2
3
4
30 (60)
1
2
3
4

Installation instructions and Instructions for use
Subject to technical modifications. – Issue June/2023 29
Mounting SOLEYA/SOLEYA protect - under-glass
Installation awning box
Single and linked units
Place the awning on two
prepared trestles.
Unpack the awning (carton,
film).
Remove the lateral covering
caps (4). To do this, loosen the
screw connection with the
lower covering profile (1) and
pull the cover cap off to the
side.
Now remove the lower
covering profile (1) by
loosening the screw
connection and unhooking the
lower covering profile from the
supporting yoke (3). Then lay
the lower covering profile
aside.
Linked units
Remove the clamping pins (2)
from the linkage and pull the
linkage apart.
Legend
Lower covering profile
Clamping pins
Supporting yoke
Lateral end cap
1
2
3
4
4
1
3
2
2
2
Installation instructions and Instructions for use
30 Subject to technical modifications. – Issue June/2023
Mounting SOLEYA/SOLEYA protect - under-glass
Installation awning box
Single and linked units
Position two ladders of the
same height below the
mounting brackets.
Place the awning box on the
top of the ladders. Please
make sure that the awning box
is placed safely and that it
cannot fall down.
Do never work in larger
heights, especially on
balconies, without suitable
fall protection devices!
Lift the awning box evenly with
two persons. Hinge the awning
box completely horizontally
into the mounting brackets (1).
Legend
Mounting bracket
Awning box (box profile)
Transport safety device
1
2
3
3
1
2
Installation instructions and Instructions for use
Subject to technical modifications. – Issue June/2023 31
Mounting SOLEYA/SOLEYA protect - under-glass
Installation awning box
Single and linked units
Legend
Mounting bracket
Awning box (box profile)
Transport safety device
Front rail
Carefully allow the front rail
(4) to move out of the
transport lock (3). To do
this, connect the motor(s)
to a test cable and operate
the awning.
Remove the small
countersunk screws from
the projecting parts of the
cheeks.
Remove the transport lock
(3).
Linked units
Position the ladders below
the mounting brackets of
the next awning.
Also hinge the awning box
carefully into the mounting
brackets, extend the front
rail and unscrew the
countersunk screws.
Remove the transport lock
(3).
1
2
3
4
2
3
3
4
1
Installation instructions and Instructions for use
32 Subject to technical modifications. – Issue June/2023
Mounting SOLEYA/SOLEYA protect - under-glass
Installation awning box
Linking the units
Put the outer (1) and the
inner part (2) of the linkage
into the linkage opening of
the right and the left
awning (only with two
awnings with one motor).
Make sure that the slits (3)
of the linkage parts engage
in the inner bolt of the
spring mechanics (4) (only
with two awnings with one
motor).
Legend
outer part of the linkage
inner part of the linkage
Slit of the linkage part
inner bolt of the spring mechanics
1
2
3
4
1
2
3
4
3
4

Installation instructions and Instructions for use
Subject to technical modifications. – Issue June/2023 33
Mounting SOLEYA/SOLEYA protect - under-glass
Installation awning box
Linking the units
To link the awnings, telescope
the awnings first and then push
both linking parts together so
that they lie on top of each
other. Turn the roller tube of the
bearing side (awning without
motor) in such a way that both
front rails are positioned exactly
parallel to one another. Tighten
the threaded pin accessible at
the threaded linkage (1). Then
turn the awning up to the next
threaded pins and tighten these
too.
Screw the middle side parts of
the two units together. Use the
connecting screws supplied for
this purpose. Screw the upper
part of the box linkage (4) to the
right side part (6) of the left unit
with the supplied countersunk
screw (5).
Legend
Threaded coupling
Fillister head screw M8x30
Hexagon nut M8
Box linkage top part
Countersunk screw M4x20
Side part of linkage
Washer 08
1
2
3
4
5
6
7
1
1
23
7
4
5
6
Installation instructions and Instructions for use
34 Subject to technical modifications. – Issue June/2023
Mounting SOLEYA/SOLEYA protect - under-glass
Installation awning box
Linking the units
As shown in the illustration, fix
the angle bracket (1) for the
cover supporting wire (5) to
one of the centre guide rails
(2), in the middle of the sloping
projection of the awning.
Legend
Angle bracket for support wires for the
cover, linkage
Guide rail
Mounting angle for cover supporting
wire
Fastening screw
Cover supporting wire
1
2
3
4
5
31
3
4
125
Installation instructions and Instructions for use
Subject to technical modifications. – Issue June/2023 35
Mounting SOLEYA/SOLEYA protect - under-glass
Installing the guide rails
Place cardboards or the like on the floor below the guide rails. Slide the
inner guide rails (1) into the upper groove of the guide rail. (only for
SOLEYA protect)
Slide in the interior guide rails (only for SOLEYA protect):
Move both guide rails (3)
simultaneously up to half
of the arms of the cheeks
(2).
Legend
Inner guide rail (only supplied with
SOLEYA protect)
Arm cheek
Guide rail
1
2
3
1
1
2
3
Installation instructions and Instructions for use
36 Subject to technical modifications. – Issue June/2023
Mounting SOLEYA/SOLEYA protect - under-glass
Installing the guide rails
Legend
Pulley
Channel for runners
Inner guide rail (only with SOLEYA
protect)
Zip fastener (only with SOLEYA
protect)
Fixing screws
Insert the runners (1) of the
pins of the front rail into the
provided channel of the guide
rails (2).
Important for SOLEYA
protect:
First thread the zip fastener (4)
into the inner guide rails (3).
Then insert the runners into
the channel provided.
Move the guide rail carefully to
the stop.
Caution with systems with
LED:
Make sure that the cable of the
LED strips is not
damaged/clamped. Notes on
cable routing on the next page.
Screw the guide rails to the
positions provided on the
inside.
Ensure that the screw heads
are completely countersunk.
Otherwise the pins of the front
rail could get caught on them.
Please make sure, that the
guide rails do not get
scratched.
1
2
3
4
5
5
1
2
34

Installation instructions and Instructions for use
Subject to technical modifications. – Issue June/2023 37
Mounting SOLEYA/SOLEYA protect - under-glass
Installing the guide rails
Attention for guide rails with
LED:
When sliding on, it must be
ensured that the cable (1) of
the LED strips is not damaged.
The cable (1) must be
threaded through under the lug
(2) and then it runs outwards
between the lug (2) and the
lower covering profile (4).
Legend
Cable for LED strips
Lug of side part
Side part
Lower covering profile
Guide rail
1
2
3
4
5
5
3
4
1
2
Installation instructions and Instructions for use
38 Subject to technical modifications. – Issue June/2023
Mounting SOLEYA/SOLEYA protect - under-glass
Installation pull cords
- Place the pull cords over the runner in the awning box (1).
- Guide the pull cords in the channel for the rollers up to the deflection
roller in the crosshead die (5). (The pull cords must be threaded through
in the guide rail behind the rollers of the carriage).
- Guide the pull cords from the bottom to the top over the deflection roller
(5).
- Return the pull cords to the top of the channel for the rollers.
- Guide the pull cord loops (3) over the bolts of the pull cord fixation (4)
(included in the accessories, it may have to be removed from the front
rail beforehand).
- Pull the pull cords (approx. 300 mm) and push the pull cord fixation (4)
into the carriages (2) until they are locked in place.
Legend
Runner in the awning box Pull cord fixation
Carriage Deflection roller in the crosshead die
Pull cord loop Carriage plug
1 4
2 5
3 6
300
1
2
5
3
4
6
2
4
3
6
4
Installation instructions and Instructions for use
Subject to technical modifications. – Issue June/2023 39
Mounting SOLEYA/SOLEYA protect - under-glass
The installation and removal of the pull cords should be performed by two
persons.
Do not twist the pull cords!
To release the pull cord fasteners, remove the small plugs (6) from the
carriages (2) and relieve the strain on the pull cords by pulling them in the
direction of the drop profile. Insert a screwdriver into the opening of the
carriages and press them down. The pull cord is now released and can be
carefully lowered. Close the opening by means of a plug again.
The pull cords are under tension.
After attaching the pull
cords, put the guide rail end
cap (1) on the guide rail. Fix
the guide rail end cap by
tightening the threaded pins
(2).
Legend
Guide rail end cap
Threaded pin M8
1
2
1
2
Installation instructions and Instructions for use
40 Subject to technical modifications. – Issue June/2023
Mounting SOLEYA/SOLEYA protect - under-glass
Installing the guide rails (mounting brackets)
Lift both guide rails evenly and push them into the mounting
brackets already installed.
Tighten the threaded pins (2) by using an Allen key (4 mm).
Legend
Mounting bracket
Threaded pin
Guide rail
1
2
3
1
2
3

Installation instructions and Instructions for use
Subject to technical modifications. – Issue June/2023 41
Mounting SOLEYA/SOLEYA protect - under-glass
Securing the box to the guide rail
Fit the box on the guide
rails (2).
To do this, tighten the
threaded pin (3) that is
already screwed into the
lug (1) of the side part.
Legend
Lug of the side part (protrudes into
the guide groove of the guide rail)
Guide rail
Threaded pin M8
1
2
3
2
1
3
32
1
Installation instructions and Instructions for use
42 Subject to technical modifications. – Issue June/2023
Mounting SOLEYA/SOLEYA protect - under-glass
Installation bottom of the awning
- Extend the awning completely.
- Position two ladders of the same height below the awning box.
- Place the floor profile on the top of the ladders. Please make sure that it
is placed safely and that it cannot fall down.
- Take the lower covering profile (2) and hook it into the supporting yoke
(1).
- Tilt up the bottom and screw it from below and from the front (3).
With linked units:
Mount the lower part of the
box linkage (4) on the awning
box. Use the supplied fixing
screw (5) for this purpose.
Legend
Supporting yoke
Lower covering profile
Fastening screw
Box linkage bottom part
Countersunk screw M4x20
1
2
3
4
5
2
1
4
5
3
3
Installation instructions and Instructions for use
Subject to technical modifications. – Issue June/2023 43
Mounting SOLEYA/SOLEYA protect - under-glass
Fix the end caps on the sides
Legend
Covering cap
Side part
Positioning nipple
Magnet
Countersunk screw M4
Lower covering profile
Put the lateral cover caps (1) onto
the side parts (2) of the awning
box. The positioning nipples (3)
must protrude into the recesses of
the side parts.
Due to the screwed magnets (4),
the cover caps are then
independently holding onto the
side part (2).
Screw the cover cap additionally
with the lower covering profile (6).
For systems with LEDs, mount
the covering caps only after the
wiring has been completed on the
box.
1
2
3
4
5
6
1
2
3
4
5
6
1
Installation instructions and Instructions for use
44 Subject to technical modifications. – Issue June/2023
Mounting SOLEYA/SOLEYA protect - under-glass
Tensioner for the cover supporting wire
From certain unit sizes
upwards, a cover support wire
tensioner is included in the
scope of delivery.
Push the screws (2) into the
slit of the bracket for the cover
supporting wire already fixed
and tighten the hexagon nuts
(1).
Cut the cover supporting wire
to the required length. (In
theory: ordering width of the
awning minus 73 mm, but
check the length in advance!)
Pass the cover supporting
cord (4) through the support
cord tensioning device for the
cover (5) into the cord clamps
(6). Tighten the locking screws
(3) by using an Allen key (2.5
mm).
Legend
Hexagon nut
Hexagon head screw
Locking screw
Cover supporting wire
Tensioner for the cover supporting wire
Wire clamp
1
2
3
4
5
6
12
3
4
5
6

Installation instructions and Instructions for use
Subject to technical modifications. – Issue June/2023 45
Mounting SOLEYA/SOLEYA protect - under-glass
Tensioner for the cover supporting wire
Legend
Cover supporting wire
Evenly turn the support wire
tensioning device for the cover
onto the screws of the bracket
for the cover supporting wire
on the left and right. Turn the
support wire tensioning device
for the cover alternately until
the cover supporting wire is
tensioned tautly.
The cover supporting wire
brackets must never be fitted
to the guide rails. The guide
rails would be pulled inwards.
4
4
Installation instructions and Instructions for use
46 Subject to technical modifications. – Issue June/2023
Mounting SOLEYA/SOLEYA protect - under-glass
Tensioner for the cover supporting wire
Cover supporting cord with linked units
Pass the cover supporting wire (2) through he bracket for the cover
supporting wire in the centre (1) through the support wire tensioning devices
(3) into the wire clamps (4).
Tighten the clamping screws (5) with an Allen key (2.5 mm).
The further installation is carried out analogously to the installation of single
units.
Legend
Angle bracket for support wires for the cover, linkage
Cover supporting wire
Tensioner for the cover supporting wire
Wire clamp
Locking screw
1
2
3
4
5
1
2
3
4
5
Installation instructions and Instructions for use
Subject to technical modifications. – Issue June/2023 47
Adjusting the Underglass Awning
Single units
Legend
Diagonal dimension
Width
Measure again the diagonal
(1) and the width (2).
The diagonal dimension as
well as the width dimensions
must be equal.
If the diagonal/width is not
correct, loosen the screws (I, II
+ III) and move the awning to
the correct dimension.
Afterwards, tighten the screws.
1
2
2
1
1
2
I
II
III
I
II
III
III
Installation instructions and Instructions for use
48 Subject to technical modifications. – Issue June/2023
Adjusting the Underglass Awning
Linked units
- Remeasure the diagonal (1) and the widths (2, 3).
- The diagonal dimension as well as the width dimensions must be equal.
- If the dimensions are not correct, please proceed as described above (single units).
When aligning, make sure that
you need a gap of 8 mm
between the guide rail (4) and
the front rail (5) on the right
and left over the entire length
of the front.
Legend
Diagonal dimension
Width 1
Width 2
Guide rail
Front rail
1
2
3
4
5
11
2
2
3
3
5
4
8

Installation instructions and Instructions for use
Subject to technical modifications. – Issue June/2023 49
Overview SOLEYA/SOLEYA protect - over-glass
Legend
Covering cap
Box
Guide rail
Front rail
Mounting bracket for top glass
Conduit
1
2
3
4
5
6
1
2
3
4
5
6
Installation instructions and Instructions for use
50 Subject to technical modifications. – Issue June/2023
Over-glass mounting brackets overview
Standard brackets
A1-F Standard A2-F Combination /
linkage
A3-F series
Type Bracket
height
A1-F85 85 mm
A1-F100 100 mm
A1-F150 150 mm
A1-F200 200 mm
Type Bracket
height
A2-F85 85 mm
A2-F100 100 mm
A2-F150 150 mm
A2-F200 200 mm
Type Bracket
height
A3-F85 85 mm
A3-F100 100 mm
A3-F150 150 mm
A3-F200 200 mm
A1-FV - 5 mm axle offset Mounting bracket
Type Bracket height
A1-FV85 85 mm
A1-FV100 100 mm
A1-FV150 150 mm
A1-FV200 200 mm
041009E0
Installation instructions and Instructions for use
Subject to technical modifications. – Issue June/2023 51
Over-glass mounting brackets overview
swivelling brackets
A1-S variable A1-SV variable / 10 mm axle offset
Type Bracket height
A1-S115 115-165
A1-S168 168-216
A1-S217 217-267
Type Bracket height
A1-SV115 115-165
A1-SV168 168-216
A1-SV217 217-267
A2-S variable / linkage A3-S variable / line
Type Bracket height
A2-S115 115-165
A2-S168 168-216
A2-S217 217-267
Type Bracket height
A3-S115 115-165
A3-S168 168-216
A3-S217 217-267
Installation instructions and Instructions for use
52 Subject to technical modifications. – Issue June/2023
Mounting SOLEYA/SOLEYA protect - over-glass
Installing the guide rails
Use an Allen key to loosen the
threaded pin (2) and remove
the clamping cones (3).
Legend
Sloping projection
Threaded pin
Clamping cone
Fix the fixing brackets to the conservatory according to the instructions
given for the appropriate mounting material (see installation sets A-E).
Please observe the minimum and maximum dimensions as shown below.
For single units, the axis dimension between the left and right guide rail is
the same as the dimensions in the order (see the delivery note). For
combined units/linkage, the axis dimension between the left and right
gmounting bracket is the same as the dimensions in the order (see the
delivery note).
Differences can be levelled out up to 14 mm by the long holes in the
mounting brackets.
Tighten the screws only to such an extent, that it is still possible to move the
holding devices in the long holes.
If the adjusting range is insufficient, the awning is too broad or too small;
consequently a modification of the awning in the production facility of the
manufacturer of the awning is required. Do never try to shorten the awning
by yourself; in these cases the right to claim under guarantee expires.
1
2
3
3
2
1
≥285 / 350 ≤2075
≤≥65 / 300
≤

Installation instructions and Instructions for use
Subject to technical modifications. – Issue June/2023 53
Mounting SOLEYA/SOLEYA protect - over-glass
Installing the guide rails
Installation set A
Legend
E-Jot screw A2 ø6.3
L = 50(80/90/100)
E-Jot sealing washer
SW 10
Foam tape 3 mm
Installation set B
Legend
SW 13
Washer M8
Hexagon wood screw ø8x80
Foam tape 3 mm
Installation set D
Legend
Universal dowel ø10
Washer M8
SW 13
Hexagon wood screw ø8x80
1
2
3
4
1
2
3
4
1
2
3
4
1
2
3
4
1
2
3
4
1
2
3
4
Installation instructions and Instructions for use
54 Subject to technical modifications. – Issue June/2023
Mounting SOLEYA/SOLEYA protect - over-glass
Installing the guide rails
Installation set C (post-and-beam construction)
Legend
Hanger bolt A2
M8 L = 100/130/200
Washer M8 large
Washer M8
Sealing washer for M8
SW 13
Screw nut M8
Installation set C (wood-aluminium construction)
Legend
Hanger bolt A2
M8 L = 100/130/200
Washer M8 large
Washer M8
Sealing washer for M8
SW 13
Screw nut M8
Installation set E
Legend
Threaded rod M8
L = 100/150
Washer M8 large
Washer M8
Sealing washer for M8
SW 13
Screw nut M8
1
2
3
4
5
6
1
2
3
4
5
6
1
2
3
4
5
6
1
2
3
4
5
6
1
2
3
4
5
6
1
2
3
4
5
6
Installation instructions and Instructions for use
Subject to technical modifications. – Issue June/2023 55
Mounting SOLEYA/SOLEYA protect - over-glass
Installing the guide rails
Slide the clamping cones (1) into the groove of the guide rails. Insert the
clamping cones (1) into the already mounted mounting brackets (2). Slightly
tighten the locking screws (4).
Only for SOLEYA protect:
Slide the clamping cones (3) into the guide rails.
From a final width of 5500 mm upwards, a box support is supplied. This
must be fitted before the box is mounted on the conservatory (see Mounting
box support).
Attention:
For installations with a guiding tube, the guiding tube holders must be fitted
before the guide rail is installed (see Mounting the guiding tube/guiding tube
support).
1
2
3
4
1
Installation instructions and Instructions for use
56 Subject to technical modifications. – Issue June/2023
Mounting SOLEYA/SOLEYA protect - over-glass
Installing the guide rails
Linked units
Series systems
Legend
Dimension between axes = ordering dimension (1st unit)
Dimension between axes = ordering dimension (2nd unit)
Mounting bracket for linked units
Mounting bracket for series systems
1
2
3
4
25 25
12
3
12
25 2552
4

Installation instructions and Instructions for use
Subject to technical modifications. – Issue June/2023 57
Mounting SOLEYA/SOLEYA protect - over-glass
Installing the guide rails
Installation in the soffit
Legend
Ordering dimension axis of the guide
rail
Angular bracket for installation in the
soffit, offset 30 mm
Mounting bracket
Guide rail
The angular brackets for the
installation in the soffit are
loosely enclosed in the
delivery.
Hold the angular bracket for
the installation in the soffit to
the wall and mark the
boreholes for the fixing.
Provide suitable boreholes
for the fixing.
Fix the angular bracket to
the mounting base by using
the appropriate mounting
material, and adjust it.
Fasten the mounting
brackets to the angular
brackets.
Please ensure that the
mounting brackets are in
alignment. If necessary, shift
them laterally.
Please observe the offset
between the axis of the
guide rail and the outer
edge of the angle of 30 mm.
1
2
3
4
30
60
60
4
3
2
1
Installation instructions and Instructions for use
58 Subject to technical modifications. – Issue June/2023
Mounting SOLEYA/SOLEYA protect - over-glass
Installation awning box
Single and linked units
Lift the awning box onto the conservatory and place it in front of the ends of
the guide rails. Use a suitable underlay, e.g. a wooden board (2), to support
the awning box so that it is at the correct height to the rail.
Carefully extend the front rail
(3) of the unit by approx. 10
cm. To do this, connect the
motor to the mounting cable.
Loosen the screws (4) on the
transport locks (1) and pull
these off towards the front.
Legend
Transport safety device
Base (mounting aid)
Front rail
Countersunk screw M4
1
2
3
4
1
2
1
3
4
Installation instructions and Instructions for use
Subject to technical modifications. – Issue June/2023 59
Mounting SOLEYA/SOLEYA protect - over-glass
Installation awning box
Single and linked units
Raise the front rail slightly.
Push the carriages into the
channel provided for this
on the guide rail. Push the
awning box with the bars
(1) of the side parts onto
the guide rails.
Important for SOLEYA
protect:
First thread the zip fastener
(5) into the inner guide rails
(3).
Then insert the carriages
into the channel provided.
Caution with systems
with LED:
See chapter “Installation of
guide rails -
SOLEYA/SOLEYA protect
under-glass”
Legend
Bars of the side parts
Carriage
Inner guide rail (only with SOLEYA
protect)
Front rail
Zip fastener
1
2
3
4
5
1
2
3
4
3
5
Installation instructions and Instructions for use
60 Subject to technical modifications. – Issue June/2023
Mounting SOLEYA/SOLEYA protect - over-glass
Installation awning box
Single and linked units
Screw the webs to the guide
rails from the inside (1).
Ensure that the screw heads
(1) are completely
countersunk. Otherwise the
carriages could get caught on
them.
Loosen the locking screws (4)
in the mounting brackets on
both sides and push the box
together with the guide rails to
the final upper position.
Tighten the locking screws.
Legend
Fixing screw (guide rail on bar/side part)
Bar of the side part
Inner guide rail
Locking screws in mounting brackets
1
2
3
4
1
2
3
1
4

Installation instructions and Instructions for use
Subject to technical modifications. – Issue June/2023 61
Mounting SOLEYA/SOLEYA protect - over-glass
Installation awning box
Linking the units
Loosen the fastening screws (1) for the roof profiles and take down the roof
profiles (2).
Carefully extend the front rail (3) by approx. 10 cm. Then loosen the fixing
screws (5) on the transportation locks (4) and pull them towards the front.
2
1
3
4
5
Installation instructions and Instructions for use
62 Subject to technical modifications. – Issue June/2023
Mounting SOLEYA/SOLEYA protect - over-glass
Installation awning box
Linking the units
Remove the clamping
pins (2) from the linkage
and pull the linkage apart.
Screw the lower part of
the box linkage (1) to the
right side part (3) of the
left half of the awning.
Legend
Box linkage bottom part
Clamping pin in threaded coupling
Side part
1
2
3
2
2
2
1
3
Installation instructions and Instructions for use
Subject to technical modifications. – Issue June/2023 63
Mounting SOLEYA/SOLEYA protect - over-glass
Installation awning box
Linking the units
Put the outer (1) and the
inner part (2) of the
linkage into the linkage
opening of the right and
the left awning (only with
two awnings with one
motor).
Make sure that the slits
(4) of the linkage parts
engage in the inner bolt of
the spring mechanics (3)
(only with two awnings
with one motor).
Legend
Outer part of the linkage
Inner part of the linkage
Inner bolt of the spring mechanics
Slit of the linkage part
1
2
3
4
1
2
4
3
Installation instructions and Instructions for use
64 Subject to technical modifications. – Issue June/2023
Mounting SOLEYA/SOLEYA protect - over-glass
Installation awning box
Linking the units
To link the awnings,
telescope the awnings first
and then push both linking
parts together so that they
lie on top of each other.
Turn the roller tube of the
bearing side (awning
without motor) such that
both front rails are
positioned exactly parallel
to one another.
Tighten the threaded pin
accessible at the threaded
linkage (1). Then turn the
awning up to the next
threaded pins and tighten
these too.
Put a suitable support
under the awning boxes,
e.g. a wooden board (2), so
that they are at the correct
height to the guide rails.
1
1
2

Installation instructions and Instructions for use
Subject to technical modifications. – Issue June/2023 65
Mounting SOLEYA/SOLEYA protect - over-glass
Installation awning box
Linking the units
Connect the awning parts with
the connecting screws (1).
Do not forget the washers
between the screw
head/hexagon nut and the side
part.
Raise the front rail slightly.
Thread the zip fastener (6) into
the inner guide rails (4). (only
with SOLEYA protect)
Push the carriages into the
channel provided for this on
the guide rail. Push the awning
box with the bars (3) of the
side bearing onto the guide
rails.
Caution with systems with
LED:
See chapter “Installation of
guide rails - SOLEYA/SOLEYA
protect under-glass”.
Legend
Connecting screws
Carriage
Bar of the side part
Inner guide rails (only with SOLEYA
protect)
Front rail
Zip fastener
1
2
3
4
5
6
1
4
2
3
5
6
4
Installation instructions and Instructions for use
66 Subject to technical modifications. – Issue June/2023
Mounting SOLEYA/SOLEYA protect - over-glass
Installation awning box
Linking the units
Refit the roof profiles (2) onto
the awning boxes. Screw the
upper part of the box linkage
(1) to the right side part of the
left half of the awning.
Legend
Box linkage top part
Roof profile
1
2
2
1
Installation instructions and Instructions for use
Subject to technical modifications. – Issue June/2023 67
Mounting SOLEYA/SOLEYA protect - over-glass
Installation pull cords
- Place the pull cords over the runner in the awning box (1).
- Guide the pull cords in the channel for the runners up to the deflection
roller in the crosshead (5). (The pull cords must be threaded through in
the guide rail behind the runners of the carriage).
- Guide the pull cords from the bottom to the top over the deflection roller
(5).
- Guide back the pull cords on the top of the channel for the runners.
- Guide the pull cord loops (3) over the bolts of the pull cord fixation (4)
(located in the accessories, it may have to be removed from the front rail
beforehand).
- Pull the pull cords (approx. 300 mm) and push the pull cord fixation (4)
into the carriages (2) until it is locked in place.
Legend
Runner in the awning box Pull cord fixation
Carriage Deflection roller in the crosshead die
Pull cord loop Carriage plug
1 4
2 5
3 6
300
34
5
2 1
3
4
2
6
6
4
Installation instructions and Instructions for use
68 Subject to technical modifications. – Issue June/2023
Mounting SOLEYA/SOLEYA protect - over-glass
Installation pull cords
The installation and removal of the pull cords should be performed by two
persons.
Do not twist the pull cords!
To release the pull cord fasteners, remove the small plugs (6) from the
carriages (2) and relieve the strain on the pull cords by pulling them in the
direction of the drop profile. Insert a screwdriver into the opening of the
carriages and press them down. The pull cord is now released and can be
carefully lowered. Close the opening by means of a plug again.
The pull cords are under tension.
Mounting guide rail end caps
After attaching the pull
cords, put the guide rail end
cap (1) on the guide rail.
Fix the guide rail end cap by
tightening the threaded pins
(2).
Legend
Guide rail end cap
Threaded pin M8
1
2
1
2

Installation instructions and Instructions for use
Subject to technical modifications. – Issue June/2023 69
Mounting SOLEYA/SOLEYA protect - over-glass
Securing the box to the guide rail
Fit the box on the guide rails
(2).
To do this, tighten the
threaded pin (3) that is
already screwed into the lug
(1) of the side part.
Legend
Lug of the side part (protrudes into
the guide groove of the guide rail)
Guide rail
Threaded pin M8
1
2
3
1
3
2
1
2
3
Installation instructions and Instructions for use
70 Subject to technical modifications. – Issue June/2023
Mounting SOLEYA/SOLEYA protect - over-glass
Installing the anti-lift device
Slide the slot stones (1) into the
groove of the guide rails (2).
Then screw one clamping part on
the spring side (3) and one
clamping part on the clamping
side (4) per unit to the slot
stones. Use the provided
fastening screws (5).
Push the pressure spring (7) into
the side hole of the clamping part
(3). Then thread the wire cable
(6) (with pressed-on sleeve)
through the clamping part (3).
Cut the wire to the appropriate
length and mount the threaded
fitting (8) on it. To do this, insert
the cable into the fitting as far as
it will go and clamp it with the two
threaded pins.
Screw the threaded fitting (8) into
the clamping part (4). This
tensions the cable.
Fix the fitting by tightening the
hexagon nut.
Mount anti-lift devices only
over guiding tubes!
Legend
Sliding block Fillister head screw M8x20
Guide rail Wire cable with pressed.on clamping sleeve
Clamping part (spring side) Pressure spring
Clamping part (clamping side) Threaded fitting M8
1 5
2 6
3 7
4 8
=
=
1
2
3
4
5
3
6
7
8
4
8
Installation instructions and Instructions for use
Subject to technical modifications. – Issue June/2023 71
Mounting SOLEYA/SOLEYA protect - over-glass
Installing the anti-lift device
The anti-lift device (1) may
always only be mounted
directly above a conduit
bracket (2).
Through tensioning the wire
cable, the guide rails could
then otherwise be
contracted. This can have a
negative impact on the
installation’s functionality.
The double guide rail (for
system
combination/coupling) has
no guide grooves on the
upper side for the sliding
blocks. Therefore, the
clamping parts must be fixed
with drilling screws (4) on the
double guide rail (3).
Legend
Anti-lift device
Conduit
Double guide rail
Self-drilling head screw 4.8x22 mm
Washer 06
1
2
3
4
5
1
2
3
4
5
Installation instructions and Instructions for use
72 Subject to technical modifications. – Issue June/2023
Mounting SOLEYA/SOLEYA protect - over-glass
Mounting the guiding tube/guiding tube support
Attach the conduit bracket (1) to
the guide rail (4). To do this, push
the sliding blocks (2) into the
groove of the guide rail and
screw the conduit bracket to the
sliding blocks using the screws
(3) supplied.
Make sure that the conduit
bracket has the same distance to
the outer edge of the guide rail
for the left and right guide rails.
Place the conduit (5) between the
guide rails and screw it to the
conduit brackets.
Conduit support:
When the conduit has been
moved to the desired position,
align the supplied conduit support
(7) with the conduit according to
the structure of the conservatory,
and mark the fixing position on
the conservatory as well as on
the conduit.
Legend
Conduit bracket
Sliding block
Fillister head screw M8x12
Guide rail
Conduit
Fillister head screw M10x55
Guiding tube support
1
2
3
4
5
6
7
1
2
3
4
5
6
7
=
=

Installation instructions and Instructions for use
Subject to technical modifications. – Issue June/2023 73
Mounting SOLEYA/SOLEYA protect - over-glass
Mounting the guiding tube/guiding tube support
Legend
Guiding tube support
Conduit
Countersunk drilling screw
3.9x13 mm
Conduit division
(1 conduit)
Conduit division
(2 conduits)
Attach the conduit support (1) to
the marked position on the
conduit (2). Use the supplied
drilling screws (3) for this
purpose. (The conduit may have
to be removed again for this).
Then screw the base plate of the
conduit support to the
conservatory. Use the appropriate
mounting material (see mounting
sets) for this.
Guiding rails distribution
1
2
3
4
5
1
2
3
==
== ~800-1000
5
4
Installation instructions and Instructions for use
74 Subject to technical modifications. – Issue June/2023
Mounting SOLEYA/SOLEYA protect - over-glass
Mounting the box support
Mount the supplied box support
(1) according to the structure of
the conservatory (2), but
preferably in the centre of the unit
width. After mounting the box (3),
the box rests on the box support
and thus does not sag. Use the
appropriate mounting material
(see mounting sets) to attach the
box support to the conservatory.
Legend
Box support
Structure (conservatory)
Box
1
2
3
1
2
3
12
Installation instructions and Instructions for use
Subject to technical modifications. – Issue June/2023 75
Aligning the over-glass awning
Single units
Legend
Diagonal dimension
Width
Measure again the diagonal
(1) and the width (2).
The diagonal dimension as
well as the width dimensions
must be equal.
If the diagonal/width is not
correct, loosen the screws (I +
II) of the mounting brackets
and move the awning to the
correct dimension.
Afterwards, tighten the screws.
1
2
2
2
1
1
I
I
I
I
I
II
Installation instructions and Instructions for use
76 Subject to technical modifications. – Issue June/2023
Aligning the over-glass awning
Linked units
When aligning, make sure that
you need a gap of 8 mm
between the guide rail (4) and
the front rail (5) on the right
and left over the entire length
of the front.
Legend
Diagonal dimension
Width 1
Width 2
Guide rail
Front rail
1
2
3
4
5
I
I
I
I
I
I
1
3
3
2
2
1
4
5
8

Installation instructions and Instructions for use
Subject to technical modifications. – Issue June/2023 77
Installation/wiring LED
(for LED in box and guide rails)
View: Box in delivery condition
View: Box with mounted guide rails (LED in box and guide rails)
In the delivery condition, the supply line (2) for the LED control unit and the connecting
cables (with STAK2) for the LED strips protrude from the upper covering profile (1).
Depending on the order, that can be up to three such connecting cables (3/4/5). If the
guide rails are mounted, 3 more cables (with STAS2) are added to the box. These are the
connecting cables of the LED strips from the two guide rails (7/8) and the lower covering
profile/box profile (6).
Legend
Roof profile Connecting cable for LED box
Supply line LED control unit Connecting cable LED strips box
Connecting cable LED FS right Connecting cable LED strips FS left
Connecting cable LED FS left Connecting cable LED strips FS right
1 5
2 6
3 7
4 8
3
1
2
45
8
6
7
Installation instructions and Instructions for use
78 Subject to technical modifications. – Issue June/2023
Installation/wiring LED
(for LED in box and guide rails)
Detail cable outlet LED in box
Detail cable outlet LED in guide rail
With LED in the boxthe
cable of the LED strip (6)
comes out of the groove of
the floor profile (9).
With LED in the guide
railthe cable of the LED strip
(7/8) comes out between the
side part (10) and the floor
profile (9).
When installing the guide
rails, make absolutely sure
that the cable of the LED
strip is not damaged or
crushed and thread it
carefully out through the gap
between the side panel and
the floor profile.
Put the Hirschmann connectors together
and stow them in the roof profile
Now connect the connection
cables of the LED control
unit (STAK2) with the
connection cables of the
LED strips (STAS2). To do
this, plug the Hirschmann
connectors together.
Then slide the Hirschmann
connectors into the
compartment of the roof
profile where the LED control
unit is also stowed.
6
9
78
9
10
Installation instructions and Instructions for use
Subject to technical modifications. – Issue June/2023 79
Installation/wiring LED
(for LED in box and guide rails)
Tighten the cables of the
LED strips and the cable of
the LED control unit tautly
and fix them with cable ties
(11) on the side part (12).
There are recesses (13) in
the side part (12), where the
cable ties can be threaded
through.
Legend
Cable LED control unit
Cable tie
Side part
Recesses for cable tie
In the case of unit
combinations, it is necessary
to remove the upper
covering profile for wiring the
LED strips.
2
11
12
13
11
11
11
12
2
13
13
13
Installation instructions and Instructions for use
80 Subject to technical modifications. – Issue June/2023
Malfunctions
What is the matter, if...
... the front rail moves to the awning box
askew?
The awning(s) was/were not diagonally
aligned during installation.
Solution: Measure the
diagonal as described in
Chapter “Aligning the under-
glass awning” and align the
awning accordingly.
The tension on the right side or guide rail is
too high or too little on the left side or guide
rail.
Solution: Check the tension
as described in Chapter
“Installation of the pull cords”.
The awning cover is sewn askew.
Solution: Place a small cover
remnant underneath the right
outer seam of the awning
cover. For this purpose it is
necessary to completely
extend the awning. This has
the effect that the awning cover
rolls up slightly thicker and
brings the front rail closer to
the awning box.
The spring mechanics on the left side is
defective.
Solution: Loosen the pull cord
on the left side. Try to turn the
tape pulley. If the tape pulley
cannot be turned at all or very
easily, the spring mechanics is
defective and must be
replaced.