Hella SOLEYA Setup guide

Installation Instructions and Instructions for Use
These instructions must be read
prior to installation
and use!
Over-glass and under-glass awning SOLEYA/SOLEYA protect
Operating guidelines
Installation Instructions and Instructions for Use
Table of Contents
Preliminary remarks HELLA Over-glass and under-glass awning SOLEYA/SOLEYA protect
.............................................................................................................................................1
General notes.......................................................................................................................2
CE Identification SOLEYA ....................................................................................................3
CE Identification SOLEYA protect ........................................................................................4
Safety instructions ................................................................................................................5
Designated use ....................................................................................................................9
Servicing, maintenance and repair .....................................................................................10
Operating guidelines...........................................................................................................13
Before installation...............................................................................................................14
Overview: Tools for the installation.....................................................................................15
Overview SOLEYA/SOLEYA protect - under-glass ............................................................16
Under-glass mounting brackets overview...........................................................................17
Mounting SOLEYA/SOLEYA protect - under-glass ............................................................21
Adjusting the Underglass Awning.......................................................................................45
Overview SOLEYA/SOLEYA protect - over-glass ..............................................................47
Over-glass mounting brackets overview.............................................................................48
Mounting SOLEYA/SOLEYA protect - over-glass ..............................................................50
Aligning the over-glass awning...........................................................................................73
Installation/wiring LED........................................................................................................75
Malfunctions .......................................................................................................................78
Wiring diagram for motors with ONYX.CONNECTOR........................................................81
Wiring diagram for motors with ONYX.NODE ....................................................................82
Wiring diagram for motors with Somfy io ............................................................................83
Wiring diagram for motors with switch operation ................................................................84
Wiring diagram for LED lighting ONYX/Somfy io................................................................85
Operating instructions and configuration with ONYX..........................................................86
Activation guidelines for electric drives...............................................................................88
Commissioning/functional check ........................................................................................89
Removal .............................................................................................................................90
Handing over report (for the fitter) ......................................................................................91
Handing over report (for the user) ......................................................................................92
Installation Instructions and Instructions for Use
Subject to technical modifications. –Date of Issue March/2021
1
Preliminary remarks HELLA
Over-glass and under-glass awning
SOLEYA/SOLEYA protect
With this HELLA product you have opted for a high-quality product with a most up-to-date
technology that can nevertheless be easily installed and operated. In these instructions we
describe the basic installation, commissioning and use.
For authorized specialist staff
For the consumer (user)
The following symbols will assist you with the installation or use and require a safety-
conscious conduct:
Attention!
This symbol indicates instructions that, if
disregarded, can put the
user in danger.
Attention!
This symbol indicates instructions that, if disregarded, can potentially
result in damage to the product.
This symbol indicates instructions for use or helpful information.
This symbol requires you to act.
Attention!
This symbol indicates a risk of injury or danger to life due to an
electric shock.
This symbol indicates parts of the product, for which you will find
important information in these installation instructions.
Installation Instructions and Instructions for Use
2
Subject to technical modifications. –Date of Issue March/2021
General notes
Questions
In case of questions concerning the installation or the use of your product, please
consult your authorized specialist shop.
Spare parts/repairs
Spare parts are available at your HELLA specialist shop. Only spare parts that are
approved by HELLA are allowed to be used.
Warranty/guarantee
Precondition for warranty and guarantee is a correct and regular maintenance of the sun
protection device (at least once a year).
Warranty claims are subject to statutory limitation periods. Service parts are excluded
from the warranty; the same applies for changes in colour and changes in
characteristics caused by UV radiation.
Liability
In case of non-observance of the directions and information given in these instructions
and in case of improper operation or unintended use, the manufacturer shall not accept
any warranty claims concerning any damage to the product. In these cases the liability
for consequential damage to any parts or persons is ruled out as well.
Legal notes
The graphs and texts of these instructions were carefully prepared. We cannot be held
liable for any errors and their potential consequences! Subject to technical modifications
to the product and to these instructions! These instructions include copyrighted
information. All rights reserved! The listed product or brand names are trademarks of the
respective owners.

Installation Instructions and Instructions for Use
Subject to technical modifications. –Date of Issue March/2021
3
CE Identification SOLEYA
The over-glass and under-glass awning SOLEYA by HELLA is in compliance with the
declaration of performance according to the Construction Products Regulation; if the unit is
operated with a motor drive it is additionally in compliance with the Machinery Directive
and the Guideline for Electromagnetic Compatibility; in case of proper use, the awning
corresponds to the basic requirements of the harmonised standard EN 13561. The
respective declarations are deposited with the manufacturers.
The CE identification applies for the delivery status of the product. The product mounted
meets the requirements of the specified standard only, if
during installation the information and instructions given in these instructions as
well as the information and instructions of the manufacturers of the screws have
been observed,
the product is installed with the recommended type and number of
fasteners/screws.
No changes, rebuildings or extensions, with the exception of those described in these
instructions, are allowed with this product. The fixed CE-label expires with any change,
rebuilding or extension.
HELLA Sonnen- und Wetterschutztechnik GmbH
A-9913 Abfaltersbach 125
21
LE-AMUM-01-001
EN 13561:2004+A1:2008
Over-glass and under-glass awnings
SOLEYA
Exterior textile sun protection
Wind resistance class 2
Installation Instructions and Instructions for Use
4
Subject to technical modifications. –Date of Issue March/2021
CE Identification SOLEYA protect
The over-glass and under-glass awning SOLEYA protect (side-seam guided) by HELLA is
in compliance with the declaration of performance according to the Construction Products
Regulation; if the unit is operated with a motor drive it is additionally in compliance with the
Machinery Directive and the Guideline for Electromagnetic Compatibility; in case of proper
use, the awning corresponds to the basic requirements of the harmonised standard EN
13561. The respective declarations are deposited with the manufacturers.
The CE identification applies for the delivery status of the product. The product mounted
meets the requirements of the specified standard only, if
during installation the information and instructions given in these instructions as
well as the information and instructions of the manufacturers of the screws have
been observed,
the product is installed with the recommended type and number of
fasteners/screws.
No changes, rebuildings or extensions, with the exception of those described in these
instructions, are allowed with this product. The fixed CE-label expires with any change,
rebuilding or extension.
HELLA Sonnen- und Wetterschutztechnik GmbH
A-9913 Abfaltersbach 125
21
LE-AUZS-01-001
EN 13561:2004+A1:2008
Over-glass and under-glass awnings
SOLEYA protect
Exterior textile sun protection
Wind resistance class 3
Installation Instructions and Instructions for Use
Subject to technical modifications. –Date of Issue March/2021
5
Safety instructions
These installation instructions refer to prefabricated elements, that (1) for
100% are made from parts, which are defined by us, and (2) which are
made in manufacturing processes, which are defined by us too; in all other
cases we do not provide any guarantee!
The safety instructions as well as the appropriate instructions must be
read carefully before installation and use. In case of non-observance of
the directions and information given in these instructions and in case of
improper installation and operation or unintended use, the manufacturer
shall not accept any warranty claims concerning any damage to the
product. In these cases the liability for consequential damage to any parts
or persons is ruled out as well.
- Follow the described installation steps and pay attention to
recommendations and notes.
- Keep these instructions in a safe place.
- All installation and removal works, as well as maintenance and repair
works are only allowed to be carried out by authorised and qualified
specialist staff.
- If switching, automatic or radio control devices are used to operate the
units, the information given in the enclosed instructions of the
manufacturer must be observed.
- During operation do not put your hand into or touch movable parts.
- Ensure that clothing or body parts cannot get caught on the unit.
- Observe the regulations for prevention of accidents of the employer's
liability insurance association!
- Before operation check the unit for visible damage. If the unit is
damaged, it should not be used; please consult authorized specialist
staff immediately.
- Risk of injury and accident due to the weight of the product!
- Take safety measures against the danger of squashing, especially
when operating the unit with automatic devices.
- Place the operating switch within sight of the unit, but not near any of
the moving parts.
- Never let children play with the unit.
A sun protection device with electric drive cannot be retracted without
current.
We therefore recommend the use of an emergency power
generating unit or a motor with an emergency crank handle, especially in
regions with frequent power failures.
Danger of suffocation!
Ensure that the foil cannot get into the hands of children. Keep the foil in a
safe place.
Installation Instructions and Instructions for Use
6
Subject to technical modifications. –Date of Issue March/2021
Safety instructions
Attention! Risk of injury or danger to life due to an electric shock!
- Set-up, examination, commissioning and error correction of the unit
must only be performed by authorised or trained expert staff (as per
VDE 0100).
- Switch off the current to the connecting lines when working at the unit.
There is danger to life! Take safety precautions against unintentional
switching on!
- Check the electrical wires regularly for damage. Do not use the unit if
any damage is found.
- Our electrically driven units are in accordance with the regulations for
power plants acc. to VDE 0100. We cannot guarantee for the
operational reliability of the unit with non-approved modifications.
- The enclosed installation instructions of the electrical devices supplied
must be observed.
Units with motor drive:
The drives used are operated with a voltage of AC 230V/50Hz. Please
check the power supply provided by your utility company before
connecting. Any other voltage can destroy the drives.
Winter operation:
Snow or ice can destroy the unit.
The unit may only be operated, if no ice or snow is lying on the cover.
During this time automatic control devices must be
switched to
manual operation.

Installation Instructions and Instructions for Use
Subject to technical modifications. –Date of Issue March/2021
7
Safety instructions
To prevent damage, please retract your sun protection device with rain,
snowfall or wind.
If automatic control devices are used, adjust the wind controller
analogously to the installed wind resistance class of your sun protection
device.
The wind class specifications apply to the structure of the unit. The
prerequisite for this is a suitable mounting base. This means that the wind
class can be downgraded based on the mounting base.
Wind resistance class 0 = wind force <4 (Beaufort),
a performance not required or not measured (according to DIN 13561) or
a product, that does not comply with the requirements of the wind
resistance class 1.
Wind resistance class 1 = wind force 4 (Beaufort),
moderate breeze, moderate wind, moves twigs and thin branches, whirls
up dust and loose paper
Velocity 20 –27 km/h = 5.5 –7.4 m/s
Wind resistance class 2 = wind force 5 (Beaufort),
fresh breeze, fresh wind. Smaller deciduous trees start to sway, white
crests are formed on lakes.
Velocity 28 –37 km/h = 7.5 –10.4 m/s
Wind resistance class 3 = wind force 6 (Beaufort),
strong wind, strong branches sway, it is difficult to hold an umbrella,
telegraph cables sough in the wind
Velocity 38 –50 km/h = 10.5 –13.8 m/s
Installation Instructions and Instructions for Use
8
Subject to technical modifications. –Date of Issue March/2021
Safety instructions
If it is necessary to lift the awning via ropes at a higher altitude, the awning
must
- be removed out of the packaging.
- be tied to the pull ropes in such a way, that a slipping out of the awning
is prevented,
- lifted evenly in a horizontal position.
The same applies for the removal of the awning.
It is not allowed that climbing aids are leaned against or fixed to the
awning. They must have a stable base and provide a firm support. Only
use climbing aids with an appropriate carrying capacity.
When working at higher heights, there is risk of falling. Please make sure
that suitable fall pr
otection devices are used.
Awnings are only allowed to be used for the purpose specified in the
instructions for use. Changes, such as extensions or rebuildings, that are
not provided by the manufacturer, are only allowed to be carried out with
the manufacturer’s written approval.
Additional loadings such as objects that are sticked to the awning or cord
tensionings can damage the awning or lead to its crashing, and are
therefore not allowed.
Installation Instructions and Instructions for Use
Subject to technical modifications. –Date of Issue March/2021
9
Designated use
Sun protection
Thermal protection
Sight screen
Anti-glare blind
Installation Instructions and Instructions for Use
10
Subject to technical modifications. –Date of Issue March/2021
Servicing, maintenance and repair
With the purchase of your awning you have opted for a high-quality product. To enjoy your awning for
as long as possible, please observe the following information:
Notes to awning covers made of brand acrylic fibres
Brand acrylic fibres, as used for awnings, are materials of the highest quality for awnings. As they are
dope-dyed, these materials show the highest light- and colour-fastness. In addition, their resistance to
tearing and resistance to weather, rotting and environmental effects is unsurpassed. Furthermore, a
special textile finishing makes them dirt-, water-, oil- and grease resistant. The awning cover is heavily
tested. At the weaving plant, at the awning manufacturer and during awning fabrication. As with other
covers, differences in the surface uniformity can also occur with the awning cover. When viewing from
the top or seeing through, you will perhaps find small knots, spots of colour, irregular runs of threads
or minimal differences and displacements in the design and rapport, as well as differences in the
colour. Please note, that the awning will cause a different colour effect in sunlight and in shade.
Naturally, the optical colour perception depends on the composition and the intensity of the emerging
light. With increasing depth of colour, more light will be absorbed and less will be reflected. Therefore
dark coloured covers let through a small amount of light, while light colours let a lot of light through.
Due to the part-absorption, the composition of the light shining through will be modified, which results
in other colour perceptions.
Due to the coloured pigments embedded in the cover and the impregnation, shadings caused
by crinkles or crumple folds can appear, that, especially with light colours, become visible as
strips of shade.
The function, strength or density of the cover will not be reduced by that. Minor differences in colours
between the different cover strips or differences in colours with regard to the collection of samples
cannot be ruled out. The fabrication of several strips also with varying widths depends on the overall
width of the awning.
Ripples in the cover and wrinkling at the seams can arise, because the cover is double rolled up at the
seams.
The highest strain is on the seams of the cover. When rolling up the cover, the seams and hems lie on
top of each other, intensifying the strain. Hems and seams will be pressed flat, increasing in length. As
a result, the lateral seams of the cover can hang down slightly.
Sagging as a result of the own weight of the cover is possible. These specified phenomenons are not
faults in the awning cover, which have been overseen in the testing; they are unavoidable due to
technical, material and physical regularities. They therefore do not entitle the customer to any refusal
or reduction of the purchase price.
Correspondingly, the guidelines for the assessment of ready-made awning covers, summarized by the
German Federal Association "Manufacture of technical textile registered association" (Bundesverband
Konfektion Technischer Textilien e. V.), are also an integral part of our conditions of sale and delivery.

Installation Instructions and Instructions for Use
Subject to technical modifications. –Date of Issue March/2021
11
Servicing, maintenance and repair
Cleaning
Cleaning
As a sun protection device fixed outside, the unit can get dirty in the
course of time. This will not reduce the usability of your unit. The
powder-coated parts of your unit will remain presentable for longer, if
they are cleaned regularly with a soft woollen cloth.
Do not use solvents, alcohol (rubbing alcohol) or scouring cleansing
agent
s!
Leaves or other foreign material lying on the awning cover and in the
awning cassette must be removed immediately. There is danger of
damage or crashing to the awning.
Preventive measures
If you have to draw in the cover in a wet condition, please draw it out for
drying when the next opportunity arises, to prevent marks caused by
mould or mildew.
Installation Instructions and Instructions for Use
12
Subject to technical modifications. –Date of Issue March/2021
Servicing, maintenance and repair
Maintenance
Maintenance
All inspection and maintenance works must be carried out by a
specialised company from HELLA or a HELLA partner. Regularly check
the electrical wires of motor driven units for damage. Check the
mechanical parts of your unit for visible damage. After exceptional
events such as storm, hail, sleet, maloperation or the like, the unit must
be checked for noticeable damage prior to operating it. If the unit is
damaged, it must not be used; consult authorized specialist staff
immediately. It is recommended to have the unit maintained by
specialist staff on an annual basis. This way wear is detected at an
early stage and damage to the unit is prevented.
An unintentional switching on of electrically driven awnings is possible.
Make sure, that the awning is switched d
ead during cleaning or
maintenance work (e.g. building cleaner).
The automatic control device must be switched dead when working in
the operating range of the awning. There is danger of squashing and
danger of fall hazards.
In addition, it has to be ensured, that an unintentional manual operation
of the awning is prevented. This may be done by disconnecting the
power supply or by unplugging the plug-in coupling from the motor.
If the awning is operated manually, the operating crank handle must be
hooked out and kept in a safe place.
Repair works
Repair works
Improper repair works may cause both risk of injury to persons or
damage to the units. All repair works must be carried out by a
specialised company from HELLA or a HELLA partner. Use original
HELLA spare parts only.
Installation Instructions and Instructions for Use
Subject to technical modifications. –Date of Issue March/2021
13
Operating guidelines
Motor drive
The awning can be extended
or retracted by activating a
switch, a hand
-held radio
transmitter or an automatic
device.
End positions:
The lower end position
(awning is extended) is
adjusted in the factory.
Please observe the enclosed
instructions of the
manufacturer of the motor if
any modification is required.
The upper end position
(awning is retracted) is
automatically switched off by
the motor by torque.
Installation Instructions and Instructions for Use
14
Subject to technical modifications. –Date of Issue March/2021
Before installation
Check the product immediately for possible shipping damage and for
compliance with the delivery receipt.
If parts are missing or damaged, please consult your supplier immediately.
Check the mounting base and ensure that the mounting material to be
used complies with the given conditions to guarantee proper installation. In
case of doubt, please seek advice from a
specialist enterprise for fixing
techniques.
The packaging cardboard box should not be exposed to humidity. To
protect it from rain during transport, it should be covered by a foil.
Carry larger units by two persons. Transport and store the units carefully
to prevent injury of persons and damage to the product.
Remove the packaging material carefully. When using a knife, be careful
not to damage the packaging content and to avoid cuts!
Dispose of the packaging material via recycling.
Caution!
A wrong installation can endanger the user seriously. Please strictly
observe the installation instructions. Close off the place of installation.
When working at higher heights, there is risk of falling. Suitable ascent
supports, scaffoldings and fall protection devices are to be used. Please
make sure that the ascent supports stand solidly and provide a firm grip.

Installation Instructions and Instructions for Use
Subject to technical modifications. –Date of Issue March/2021
15
Overview: Tools for the installation
Battery-powered drill
Depending on the
mounting base (Bit AW 10,
AW 20)
Bit extension
Drilling bit
Drill set
acc. to Mounting base
Level
Measuring tape
Pencil
Screwdriver
Spanners
or ratchet
Allen key
Combination pliers or
long-nosed pliers
Side cutter
Installation Instructions and Instructions for Use
16
Subject to technical modifications. –Date of Issue March/2021
Overview SOLEYA/SOLEYA protect - under-glass
Legend
Covering cap
Mounting bracket for wall/ceiling installation
Box (3-part)
Guide rail
Tensioner for the cover supporting wire
Mounting bracket guide rail
Front rail
1
23
4
5
6
7
Installation Instructions and Instructions for Use
Subject to technical modifications. –Date of Issue March/2021
17
Under-glass mounting brackets overview
Standard brackets
Mounting bracket guide
rail
Mounting angle ceiling
installation
Mounting bracket wall
installation
U1-F30
Type
Bracket
height
U1-F30
30 mm
DU-157
Type
Bracket
height
DU-157
157 mm
WU-120
Type
Bracket
height
WU-120
120 mm
Mounting bracket guide
rail, linkage
Mounting bracket guide
rail, line
U2-F30
Type
Bracket
height
U2-F30
30 mm
U4-F30
Type
Bracket
height
U4-F30
30 mm
Installation Instructions and Instructions for Use
18
Subject to technical modifications. –Date of Issue March/2021
Under-glass mounting brackets overview
Standard brackets
Tensioner for the cover supporting wire
Angle bracket for support wires for the
cover, linkage
TU-135
Type
Bracket height
TU-135
135 mm
04170514
Bracket height
110 mm

Installation Instructions and Instructions for Use
Subject to technical modifications. –Date of Issue March/2021
19
Under-glass mounting brackets overview
Special brackets
Mounting bracket guide
rail
Mounting bracket guide
rail, linkage
Mounting bracket guide
rail, line
U1-F
Type
Bracket
height
U1-F80
80 mm
U1-F130
130 mm
U2-F
Type
Bracket
height
U2-F80
80 mm
U2-F130
130 mm
U4-F
Type
Bracket
height
U4-F80
80 mm
U4-F130
130 mm
Mounting angle ceiling installation
Tensioner for the cover supporting wire
DU-200
Type
Bracket height
DU-200
200 mm
Type
Bracket height
TU-185
185 mm
TU-235
235 mm
Installation Instructions and Instructions for Use
20
Subject to technical modifications. –Date of Issue March/2021
Under-glass mounting brackets overview
Special brackets
04210512
04210524
04210525
Mounting bracket for guide
rail
30x40 mm
Mounting bracket for guide
rail
50x50 mm
Mounting bracket for guide
rail
80x60 mm
04210526
Mounting bracket for
distance, motor/bearing
side
Installation Instructions and Instructions for Use
Subject to technical modifications. –Date of Issue March/2021
21
Mounting SOLEYA/SOLEYA protect - under-glass
Fastening mounting brackets
Please check, if the mounting
brackets supplied comply
with your order.
The mounting angles are
installed staggered to the
second rafter opposite of the
mounting brackets
respectively.
Adjust the mounting angles in
height and depth by using a
chalk line.
Mark the boreholes on the
rafter.
Bore the holes at the
specified positions, and fix
the mounting brackets.
Legend
Mounting angle for ceiling installation
Mounting angle for wall installation
Mounting bracket for guide rail 30 mm
12
157
1 2
3
Installation Instructions and Instructions for Use
22
Subject to technical modifications. –Date of Issue March/2021
Mounting SOLEYA/SOLEYA protect - under-glass
Fastening mounting brackets
Linked units
Adjust the mounting angles in
height and depth by using a
chalk line.
Legend
Mounting angle for ceiling installation
Mounting bracket for wall installation
Chalk line
1
3
2
3

Installation Instructions and Instructions for Use
Subject to technical modifications. –Date of Issue March/2021
23
Mounting SOLEYA/SOLEYA protect - under-glass
Fastening mounting brackets
Please check, if the mounting
brackets provided for the
guide rails comply with your
order.
Loosen the clamping pin by
means of an Allen key (4
mm).
Mark the mounting brackets
on the rafters. Bore the holes
at the specified positions, and
fix the mounting brackets.
Please ensure that the
mounting brackets are in
alignment. If necessary, shift
them laterally.
Legend
Mounting bracket for guide rails 30
mm, standard design
Mounting bracket for guide rails,
linkage
1
2
Installation Instructions and Instructions for Use
24
Subject to technical modifications. –Date of Issue March/2021
Mounting SOLEYA/SOLEYA protect - under-glass
Fastening mounting brackets
Installation angle bracket for support wires for the cover
Legend
Mounting angle ceiling
installation
Mounting bracket for guide rails,
under-glass
Angle bracket for support wires
for the cover
If the width or projection of
the awning field exceeds
4000 mm, the cover may
increasingly sag. By using an
additional cover supporting
wire, it is possible to avoid
this effect.
As shown above, fix the
angle brackets (3) to the
outermost rafter, in the
middle of the sloping
projection of the awning.
The fixing dimension middle
of the hole of the mounting
brackets (2) is also the fixing
dimension middle of the hole
of the angle brackets (3).
350 ≤ 2000 80-300
1
23
2
3
Installation Instructions and Instructions for Use
Subject to technical modifications. –Date of Issue March/2021
25
Mounting SOLEYA/SOLEYA protect - under-glass
Fastening mounting brackets
Linked units
Legend
Dimension between axes = ordering dimension (1st unit)
Dimension between axes = ordering dimension (2nd unit)
Mounting angle for ceiling installation
12
3
Installation Instructions and Instructions for Use
26
Subject to technical modifications. –Date of Issue March/2021
Mounting SOLEYA/SOLEYA protect - under-glass
Fastening mounting brackets
Installation in the soffit
Legend
Ordering dimension axis of the
guide rail
Angle for soffit installation,
dimensions between axes 30 mm
(60 mm)
Mounting bracket for guide rail,
under-glass
Guide rail
The angular brackets for the
installation in the soffit are
loosely enclosed in the
delivery.
Hold the angular bracket for
the installation in the soffit to
the wall and mark the
boreholes for the fixing.
Provide suitable boreholes
for the fixing.
Fix the angular bracket to the
mounting base by using the
appropriate mounting
material, and adjust it.
Fasten the mounting brackets
to the angular brackets.
Please ensure that the
mounting brackets are in
alignment. If necessary, shift
them laterally.
Observe the axis offset
between the axis of the guide
rail and the outer edge of the
angle of 30 mm or 60 mm.
30 (60)
1
2
3
4

Installation Instructions and Instructions for Use
Subject to technical modifications. –Date of Issue March/2021
27
Mounting SOLEYA/SOLEYA protect - under-glass
Installation awning box
Single and linked units
Place the awning on two
prepared trestles.
Unpack the awning (carton,
film).
Remove the side end caps
(4). To do this, loosen the
screw connection with the
floor profile (1) and pull the
cover cap off to the side.
Now remove the floor profile
(1) by loosening the screw
connection and unhooking
the floor profile from the
support bracket (3). Then put
the floor profile aside.
Linked units
Remove the clamping pins
(2) from the linkage and pull
the linkage apart.
Legend
Lower covering profile
Clamping pins
Supporting yoke
Lateral end cap
4
1
3
2
2
2
Installation Instructions and Instructions for Use
28
Subject to technical modifications. –Date of Issue March/2021
Mounting SOLEYA/SOLEYA protect - under-glass
Installation awning box
Single and linked units
Position two ladders of the
same height below the
mounting brackets.
Place the awning box on the
top of the ladders. Please
make sure that the awning
box is placed safely and that
it cannot fall down.
Do never work in larger
heights, especially on
balconies, without suitable
fall protection devices!
Lift the awning box evenly
with two persons. Hinge the
awning box completely
horizontally into the mounting
brackets (1).
Legend
Mounting bracket
Awning box (box profile)
Transport safety device
3
1
2
Installation Instructions and Instructions for Use
Subject to technical modifications. –Date of Issue March/2021
29
Mounting SOLEYA/SOLEYA protect - under-glass
Installation awning box
Single and linked units
Legend
Mounting bracket
Awning box (box profile)
Transport safety device
Front rail
Carefully allow the front
rail (4) to move out of the
transport lock (3). To do
this, connect the motor(s)
to a test cable and
activate the awning.
Remove the small
countersunk screws from
the projecting parts of the
cheeks.
Remove the transport lock
(3).
Linked units
Position the ladders below
the mounting brackets of
the next awning.
Also hinge the awning box
carefully into the mounting
brackets, extend the front
rail and unscrew the
countersunk screws.
Remove the transport lock
(3).
2
3
3
4
1
Installation Instructions and Instructions for Use
30
Subject to technical modifications. –Date of Issue March/2021
Mounting SOLEYA/SOLEYA protect - under-glass
Installation awning box
Linking the units
Put the outer (1) and the
inner part (2) of the
linkage into the linkage
opening of the right and
the left awning (only with
two awnings with one
motor).
Make sure that the slits of
the linkage parts (3)
engage in the inner bolt of
the spring mechanics (4)
(only with two awnings
with one motor).
Legend
outer part of the linkage
inner part of the linkage
Slit of the linkage part
inner bolt of the spring mechanics
1
2
3
4
3
4

Installation Instructions and Instructions for Use
Subject to technical modifications. –Date of Issue March/2021
31
Mounting SOLEYA/SOLEYA protect - under-glass
Installation awning box
Linking the units
To link the awnings, telescope
the awnings first and then push
both linking parts together so
that they lie on top of each
other. Turn the roller tube of
the bearing side (awning
without motor) in such a way
that both front rails are
positioned exactly parallel to
one another. Tighten the
threaded pin accessible at the
threaded linkage (1). Then turn
the awning up to the next
threaded pins and tighten
these too.
Screw the middle side parts of
the two units together. To do
this, use the provided
connecting screws. Then screw
the upper part of the box
linkage (4) to the right side part
(6) of the left unit with the
provided countersunk screw (5).
Legend
Threaded coupling
Cylinder head screw M8x30
Hexagon nut M8
Box linkage top part
Countersunk screw M4x20
Side part linkage
Washer 08
1
1
23
7
4
5
6
Installation Instructions and Instructions for Use
32
Subject to technical modifications. –Date of Issue March/2021
Mounting SOLEYA/SOLEYA protect - under-glass
Installation awning box
Linking the units
As shown in the illustration,
fix the angle bracket (1) for
the cover supporting wire (5)
to one of the c
entre guide
rails (2), in the middle of the
sloping projection of the
awning.
Legend
Angle bracket for support wires for the
cover, linkage
Guide rail
Mounting bracket for cover support
wires
Fastening screw
Cover supporting wire
31
3
4
125
Installation Instructions and Instructions for Use
Subject to technical modifications. –Date of Issue March/2021
33
Mounting SOLEYA/SOLEYA protect - under-glass
Installing the guide rails
Place cardboards or the like on the floor below the guide rails. Slide the
inner guide rails (1) into the upper groove of the guide rail. (only for
SOLEYA protect)
Slide in the interior guide rails (only for SOLEYA protect):
Move both guide rails (3)
simultaneously up to half
of the arms of the cheeks
(2).
Legend
Interior guide rail (only included
with SOLEYA protect)
Arm cheek
Guide rail
1
1
2
3
Installation Instructions and Instructions for Use
34
Subject to technical modifications. –Date of Issue March/2021
Mounting SOLEYA/SOLEYA protect - under-glass
Installing the guide rails
Legend
Pulley
Groove for rollers
Interior guide rail (only for
SOLEYA protect)
Zip (only for SOLEYA protect)
Fixing screws
Insert the runners (1) of the
pins of the front rail into the
provided channel of the guide
rails (2).
Important for SOLEYA
protect:
First thread the
zip (4) into
the inner guide strips (3).
Then insert the rollers into
the designated groove.
Move the guide rail carefully
to the stop.
Be careful with systems
with LED:
Make sure that the cable of
the LED strips is not
damaged/trapped. See next
page for cable routing
instructions.
Fix the guide rails to the
respective positions on the
inside.
Ensure that the screw heads
are completely countersunk.
Otherwise the pins of the
front rail could get caught on
them.
Please make sure, that the
guide rails do not get
scratched.
5
1
2
34

Installation Instructions and Instructions for Use
Subject to technical modifications. –Date of Issue March/2021
35
Mounting SOLEYA/SOLEYA protect - under-glass
Installing the guide rails
Pay attention to the
following for guide rails
with LED:
When sliding
on, it is
essential to ensure that the
cable (1) of the LED strips is
not damaged. The cable (1)
must be threaded under the
tab (2) and then it runs
outwards between the tab (2)
and the floor profile (4).
Legend
LED strip cable
Side part tab
Side part
Lower covering profile
Guide rail
5
3
4
1
2
Installation Instructions and Instructions for Use
36
Subject to technical modifications. –Date of Issue March/2021
Mounting SOLEYA/SOLEYA protect - under-glass
Installation pull cords
- Place the pull cords over the runner in the awning box (1).
- Guide the pull cords in the channel for the rollers up to the deflection
roller in the crosshead die (5). (The pull cords must be threaded
through in the guide rail behind the rollers of the carriage).
- Guide the pull cords from the bottom to the top over the deflection roller
(5).
- Return the pull cords to the top of the channel for the rollers.
- Guide the pull cord loops (3) over the bolts of the pull cord fixation (4)
(included in the accessories, it may have to be removed from the front
rail beforehand).
- Pull the pull cords (approx. 300 mm) and push the pull cord fixation (4)
into the carriages (2) until they are locked in place.
Legend
Runner in the awning box
Pull cord fixation
Carriage
Deflection roller in the crosshead die
Pull cord loop
Carriage plug
300
1
2
5
3
4
6
2
4
3
6
4
Installation Instructions and Instructions for Use
Subject to technical modifications. –Date of Issue March/2021
37
Mounting SOLEYA/SOLEYA protect - under-glass
The installation and removal of the pull cords should be performed by two
persons.
Do not twist the pull cords!
To release the pull cord fasteners, remove the small plugs (6) from the
carriages (2) and relieve the strain on the pull cords by pulling them in the
direction of the drop profile. Insert a screwdriver into the opening of the
carriages and press them down. The pull cord is now released and can be
carefully lowered. Close the opening by means of a plug again.
The pull cords are under tension.
After attaching the pull
cords, put the guide rail
end cap (1) on the guide
rail. Secure the
guide rail
end cap by screwing down
the threaded pins (2).
Legend
Guide rail end cap
Threaded pin M8
1
2
Installation Instructions and Instructions for Use
38
Subject to technical modifications. –Date of Issue March/2021
Mounting SOLEYA/SOLEYA protect - under-glass
Installing the guide rails (mounting brackets)
Lift both guide rails evenly and push them into the mounting
brackets already installed.
Tighten the threaded pins (2) by using an Allen key (4 mm).
Legend
Mounting bracket
Threaded pin
Guide rail
1
2
3

Installation Instructions and Instructions for Use
Subject to technical modifications. –Date of Issue March/2021
39
Mounting SOLEYA/SOLEYA protect - under-glass
Securing the box to the guide rail
Secure the box on the
guide rails (2).
To do this, tighten the
threaded pin (3) that is
already screwed into the
tab (1) of the side part.
Legend
Tab of the side part (protrudes into
the guide groove of the guide rail)
Guide rail
Threaded pin M8
2
1
3
32
1
Installation Instructions and Instructions for Use
40
Subject to technical modifications. –Date of Issue March/2021
Mounting SOLEYA/SOLEYA protect - under-glass
Installation bottom of the awning
- Extend the awning completely.
- Position two ladders of the same height below the awning box.
- Place the floor profile on the top of the ladders. Please make sure that it
is placed safely and that it cannot fall down.
- Take the lower covering profile (2) and hook it into the supporting yoke
(1).
- Tilt up the bottom and screw it from below and from the front (3).
With linked units:
Mount the lower part of the
box linkage (4) on the awning
box. Use the provided
fastening screw (5).
Legend
Supporting yoke
Lower covering profile
Fastening screw
Box linkage bottom part
Countersunk screw M4x20
2
1
4
5
3
3
Installation Instructions and Instructions for Use
Subject to technical modifications. –Date of Issue March/2021
41
Mounting SOLEYA/SOLEYA protect - under-glass
Fix the end caps on the sides
Legend
Covering cap
Side part
Positioning knob
Magnet
Countersunk screw M4
Lower covering profile
Stick the lateral end caps (1) on
the side parts (2) of the awning
box. The positioning knobs (3)
must protrude into the recesses
of the side parts.
Then the covering caps are held
independently on the side part
(2) due to the screwed-on
magnets (4).
Screw the cover cap to the floor
profile (6) as well.
For installations with LEDs, do
not mount the cover caps until
after the wiring to the box has
been installed.
1
2
3
4
5
6
1
Installation Instructions and Instructions for Use
42
Subject to technical modifications. –Date of Issue March/2021
Mounting SOLEYA/SOLEYA protect - under-glass
Tensioner for the cover supporting wire
From certain unit sizes
upwards, a cover support
wire tensioner is included in
the scope of delivery.
Push the screws (2) into the
slit of the bracket for the
cover supporting wire already
fixed and tighten the hexagon
nuts (1).
Cut the cover supporting wire
to the required length. (In
theory: ordering width of the
awning minus 73 mm, but
check the length in advance!)
Pass the cover supporting
cord (4) through the support
cord tensioning device for the
cover (5) into the cord clamps
(6). Tighten the locking
screws (3) by using an Allen
key (2.5 mm).
Legend
Hexagon nut
Hexagon head screw
Locking screw
Cover supporting wire
Tensioner for the cover supporting wire
Wire clamp
12
3
4
5
6

Installation Instructions and Instructions for Use
Subject to technical modifications. –Date of Issue March/2021
43
Mounting SOLEYA/SOLEYA protect - under-glass
Tensioner for the cover supporting wire
Legend
Cover supporting wire
Evenly turn the support wire
tensioning device for the
cover onto the screws of the
bracket for the cover
supporting wire on the left
and right. Turn the support
wire tensioning device for the
cover alternately until the
cover supporting wire is
tensioned tautly.
The cover support wire
brackets must not be fitted to
the guide rails under any
circumstances. The guide
rails would be pulled inwards.
4
Installation Instructions and Instructions for Use
44
Subject to technical modifications. –Date of Issue March/2021
Mounting SOLEYA/SOLEYA protect - under-glass
Tensioner for the cover supporting wire
Cover supporting cord with linked units
Pass the cover supporting wire (2) through the angle bracket (1) in the
middle through the support wire tensioning device for the cover (3) into the
wire clamps (4).
Tighten the locking screws (5) by using an A
llen key (2.5 mm).
The further installation is carried out analogously to the installation of
single units.
Legend
Angle bracket for support wires for the cover, linkage
Cover supporting wire
Tensioner for the cover supporting wire
Wire clamp
Locking screw
1
2
3
4
5
Installation Instructions and Instructions for Use
Subject to technical modifications. –Date of Issue March/2021
45
Adjusting the Underglass Awning
Single units
Legend
Diagonal dimension
Width
Measure again the diagonal
(1) and the width (2).
The diagonal dimension as
well as the width dimensions
must be equal.
If the diagonal/width is not
correct, loosen the screws (I,
II + III) and move the awning
to the correct dimension.
Afterwards, tighten the
screws.
2
1
1
2
I
II
III
I
II
III
III
Installation Instructions and Instructions for Use
46
Subject to technical modifications. –Date of Issue March/2021
Adjusting the Underglass Awning
Linked units
- Remeasure the diagonal (1) and the widths (2, 3).
- The diagonal dimension as well as the width dimensions must be equal.
- If the dimensions are not correct, please proceed as described above (single units).
When aligning, remember
that there should be a gap of
8 mm between the guide rail
(4) and the front rail (5) on
the right and left over the
entire length of the front rail.
Legend
Diagonal dimension
Width 1
Width 2
Guide rail
Front rail
11
2
2
3
3
5
4
8

Installation Instructions and Instructions for Use
Subject to technical modifications. –Date of Issue March/2021
47
Overview SOLEYA/SOLEYA protect - over-glass
Legend
Covering cap
Box
Guide rail
Front rail
Mounting bracket over-glass
Guiding tube
1
2
3
4
5
6
Installation Instructions and Instructions for Use
48
Subject to technical modifications. –Date of Issue March/2021
Over-glass mounting brackets overview
Standard brackets
A1-F Standard
A2-F Combination /
linkage
A3-F series
Type
Bracket
height
A1-F85
85 mm
A1-F100
100 mm
A1-F150
150 mm
A1-F200
200 mm
Type
Bracket
height
A2-F85
85 mm
A2-F100
100 mm
A2-F150
150 mm
A2-F200
200 mm
Type
Bracket
height
A3-F85
85 mm
A3-F100
100 mm
A3-F150
150 mm
A3-F200
200 mm
A1-FV - 5 mm axle offset
Mounting bracket
Type
Bracket height
A1-FV85
85 mm
A1-FV100
100 mm
A1-FV150
150 mm
A1-FV200
200 mm
041009E0
Installation Instructions and Instructions for Use
Subject to technical modifications. –Date of Issue March/2021
49
Over-glass mounting brackets overview
swivelling brackets
A1-S variable
A1-SV variable / 10 mm axle offset
Type
Bracket height
A1-S115
115-165
A1-S168
168-216
A1-S217
217-267
Type
Bracket height
A1-SV115
115-165
A1-SV168
168-216
A1-SV217
217-267
A2-S variable / linkage
A3-S variable / line
Type
Bracket height
A2-S115
115-165
A2-S168
168-216
A2-S217
217-267
Type
Bracket height
A3-S115
115-165
A3-S168
168-216
A3-S217
217-267
Installation Instructions and Instructions for Use
50
Subject to technical modifications. –Date of Issue March/2021
Mounting SOLEYA/SOLEYA protect - over-glass
Installing the guide rails
Use an Allen key to loosen
the set screws (2) and
remove the clamping cones
(3).
Legend
Sloping projection
Threaded pin
Clamping cone
Fix the fixing brackets to the conservatory according to the instructions
given for the appropriate installation material (see installation sets A
-
E).
Please observe the minimum and maximum dimensions as shown below.
For single units, the axis dimension between the left and right guide rail is
the same as the dimensions in the order (see the delivery note). For
combined units/linkage, the axis dimension between the left and right
gmounting bracket is the same as the dimensions in the order (see the
delivery note).
Differences can be levelled out up to 14 mm by the long holes in the
mounting brackets.
Tighten the screws only to such an extent, that it is still possible to move
the holding devices in the long holes.
If the adjusting range is insufficient, the awning is too broad or too small;
consequently a modification of the awning in the production facility of the
manufacturer of the awning is required. Do never try to shorten the awning
by yourself; in these cases the right to claim under guarantee expires.
3
2
1
≥285 / 350 ≤2075
≤≥65 / 300
≤

Installation Instructions and Instructions for Use
Subject to technical modifications. –Date of Issue March/2021
51
Mounting SOLEYA/SOLEYA protect - over-glass
Installing the guide rails
Installation set A
Legend
E-Jot screw A2 ø6.3
L = 50(80/90/100)
E-Jot sealing washer
SW 10
Foam tape 3 mm
Installation set B
Legend
SW 13
Plain washer M8
Hexagon wood screw ø8x80
Foam tape 3 mm
Installation set D
Legend
Universal dowel ø10
Plain washer M8
SW 13
Hexagon wood screw ø8x80
1
2
3
4
1
2
3
4
1
2
3
4
Installation Instructions and Instructions for Use
52
Subject to technical modifications. –Date of Issue March/2021
Mounting SOLEYA/SOLEYA protect - over-glass
Installing the guide rails
Installation set C (post-and-beam construction)
Legend
Hanger bolt A2
M8 L = 100/130/200
U-shaped washer M8 large
U-shaped washer M8
Sealing washer for M8
SW 13
Screw nut M8
Installation set C (wood-aluminium construction)
Legend
Hanger bolt A2
M8 L = 100/130/200
U-shaped washer M8 large
U-shaped washer M8
Sealing washer for M8
SW 13
Screw nut M8
Installation set E
Legend
Threaded rod M8
L = 100/150
U-shaped washer M8 large
U-shaped washer M8
Sealing washer for M8
SW 13
Screw nut M8
1
2
3
4
5
6
1
2
3
4
5
6
1
2
3
4
5
6
Installation Instructions and Instructions for Use
Subject to technical modifications. –Date of Issue March/2021
53
Mounting SOLEYA/SOLEYA protect - over-glass
Installing the guide rails
Slide the clamping cones (1) into the groove of the guide rails. Insert the
clamping cones (1) into the already mounted mounting brackets (2).
Slightly tighten the locking screws
(4).
Only for SOLEYA protect:
Slide the clamping cones (3) into the guide rails.
From a final width of 5500 mm upwards, a box support is supplied. This
must be fitted before the box is mounted on the conservatory (see
Mounting box support).
Attention:
For installations with a guiding tube, the guiding tube holders must be
fitted before the guide rail is installed (see Mounting the guiding
tube/guiding tube support).
1
2
3
4
1
Installation Instructions and Instructions for Use
54
Subject to technical modifications. –Date of Issue March/2021
Mounting SOLEYA/SOLEYA protect - over-glass
Installing the guide rails
Linked units
In-line units
Legend
Dimension between axes = ordering dimension (1st unit)
Dimension between axes = ordering dimension (2nd unit)
Mounting bracket for linked units
Mounting bracket for in-line units
25 25
12
3
12
25 2552
4

Installation Instructions and Instructions for Use
Subject to technical modifications. –Date of Issue March/2021
55
Mounting SOLEYA/SOLEYA protect - over-glass
Installing the guide rails
Installation in the soffit
Legend
Ordering dimension axis of the guide
rail
Angle for soffit installation,
dimensions between axes 30 mm
Mounting bracket
Guide rail
The angular brackets for
the installation in the soffit
are loosely enclosed in the
delivery.
Hold the angular bracket
for the installation in the
soffit to the wall and mark
the boreholes for the fixing.
Provide suitable boreholes
for the fixing.
Fix the angular bracket to
the mounting base by
using the appropriate
mounting material, and
adjust it.
Fasten the mounting
brack
ets to the angular
brackets.
Please ensure that the
mounting brackets are in
alignment. If necessary,
shift them laterally.
Observe the axis offset
between the axis of the
guide rail and the outer
edge of the angle of
30 mm.
30
60
60
4
3
2
1
Installation Instructions and Instructions for Use
56
Subject to technical modifications. –Date of Issue March/2021
Mounting SOLEYA/SOLEYA protect - over-glass
Installation awning box
Single and linked units
Lift the awning box onto the conservatory and place it in front of the ends
of the guide rails. Use a sui
table underlay, e.g. a wooden board (2), to
support the awning box so that it is at the correct height to the rail.
Carefully extend the front rail
(3) of the unit by approx. 10
cm. To do this, connect the
motor to the mounting cable.
Loosen the screws (4) on the
transportation locks (1) and
pull them towards the front.
Legend
Transport safety device
Underlay (mounting aid)
Front rail
Countersunk screw M4
1
2
1
3
4
Installation Instructions and Instructions for Use
Subject to technical modifications. –Date of Issue March/2021
57
Mounting SOLEYA/SOLEYA protect - over-glass
Installation awning box
Single and linked units
Slightly raise the front rail.
Push the carriages into
the designated groove of
the guide rail. Push the
awning box with the webs
(1) of the side parts onto
the guide rails.
Important for SOLEYA
protect:
First thread the zip (5) into
the inner guide strips (3).
Then insert the carriages
into the designated
groove.
Be careful with systems
with LED:
See chapter “Mounting
the guide rails -
SOLEYA/SOLEYA protect
under-glass”
Legend
Side parts’ webs
Carriage
Interior guide rail (only for
SOLEYA protect)
Front rail
Zip
1
2
3
4
3
5
Installation Instructions and Instructions for Use
58
Subject to technical modifications. –Date of Issue March/2021
Mounting SOLEYA/SOLEYA protect - over-glass
Installation awning box
Single and linked units
Screw the webs to the guide
rails from the inside (1).
Ensure that the screw heads
(1) are completely
countersunk. Otherwise the
carriages could get caught on
them.
Loosen the locking screws
(4) in the mounting brackets
on both sides and push the
box together with the guide
rails to the final upper
position. Tighten the locking
screws.
Legend
Fixing screw (guide rail on web/side part)
Side part web
Inner guide strip
Locking screws in the mounting brackets
1
2
3
1
4

Installation Instructions and Instructions for Use
Subject to technical modifications. –Date of Issue March/2021
59
Mounting SOLEYA/SOLEYA protect - over-glass
Installation awning box
Linking the units
Loosen the fastening screws (1) for the roof profiles and take down the
roof profiles (2).
Carefully extend the front rail (3) by approx. 10 cm. Then loosen the fixing
screws (5) on the transportation locks (4) and pull them towards the front.
2
1
3
4
5
Installation Instructions and Instructions for Use
60
Subject to technical modifications. –Date of Issue March/2021
Mounting SOLEYA/SOLEYA protect - over-glass
Installation awning box
Linking the units
Remove the clamping
pins (2) from the linkage
and pull the linkage
apart.
Screw the lower part of
the box linkage (1) to the
right side part (3) of the
left awning half.
Legend
Box linkage bottom part
Clamping pins in threaded
coupling
Side part
2
2
2
1
3
Installation Instructions and Instructions for Use
Subject to technical modifications. –Date of Issue March/2021
61
Mounting SOLEYA/SOLEYA protect - over-glass
Installation awning box
Linking the units
Put the outer (1) and the
inner part (2) of the
linkage into the linkage
opening of the right and
the left awning (only with
two awnings with one
motor).
Make sure that the slits
of the linkage parts (4)
engage in the inner bolt
of the spring mechanics
(3) (only with two
awnings with one motor).
Legend
Outer part of the linkage
Inner part of the linkage
Inner bolt of the spring
mechanics
Slit of the linkage part
1
2
4
3
Installation Instructions and Instructions for Use
62
Subject to technical modifications. –Date of Issue March/2021
Mounting SOLEYA/SOLEYA protect - over-glass
Installation awning box
Linking the units
To link the awnings,
telescope the awnings
first and then push both
linking parts together so
that they lie on top of
each other. Turn the roller
tube of the bearing side
(awning without motor) in
such a way that both front
rails are positioned
exactly parallel to one
another.
Tighten the threaded pin
accessible at the threaded
linkage (1). Then turn the
awning up to the next
threaded pins and tighten
these too.
Put a suitable support
under the awning boxes,
e.g. a wooden board (2),
so that they are at the
correct height to the guide
rails.
1
1
2

Installation Instructions and Instructions for Use
Subject to technical modifications. –Date of Issue March/2021
63
Mounting SOLEYA/SOLEYA protect - over-glass
Installation awning box
Linking the units
Connect the awning parts
with the connecting screws
(1).
Do not forget the washers
between the bolt
head/hexagon nut and the
side part.
Slightly raise the front rail.
Thread the zip (6) into the
inner guide strips (4). (only
for SOLEYA protect)
Push the carriages into the
designated groove of the
guide rail. Push the awning
box with the webs (3) of the
side bearings onto the guide
rails.
Be careful with systems
with LED:
See chapter “Mounting the
guide rails -
SOLEYA/SOLEYA protect
under-glass”
Legend
Connecting screws
Carriage
Side part web
Interior guide rails (only for SOLEYA
protect)
Front rail
Zip
1
4
2
3
5
6
4
Installation Instructions and Instructions for Use
64
Subject to technical modifications. –Date of Issue March/2021
Mounting SOLEYA/SOLEYA protect - over-glass
Installation awning box
Linking the units
Refit the roof profiles (2) onto
the awning boxes. Screw the
upper part of the box linkage
(1) to the right side part of the
left awning half.
Legend
Box linkage top part
Roof profile
2
1
Installation Instructions and Instructions for Use
Subject to technical modifications. –Date of Issue March/2021
65
Mounting SOLEYA/SOLEYA protect - over-glass
Installation pull cords
- Place the pull cords over the runner in the awning box (1).
- Guide the pull cords in the channel for the rollers up to the deflection
roller in the crosshead die (5). (The pull cords must be threaded
through in the guide rail behind the rollers of the carriage).
- Guide the pull cords from the bottom to the top over the deflection roller
(5).
- Return the pull cords to the top of the channel for the rollers.
- Guide the pull cord loops (3) over the bolts of the pull cord fixation (4)
(included in the accessories, it may have to be removed from the front
rail beforehand).
- Pull the pull cords (approx. 300 mm) and push the pull cord fixation (4)
into the carriages (2) until they are locked in place.
Legend
Runner in the awning box
Pull cord fixation
Carriage
Deflection roller in the crosshead die
Pull cord loop
Carriage plug
300
34
5
2 1
3
4
2
6
6
4
Installation Instructions and Instructions for Use
66
Subject to technical modifications. –Date of Issue March/2021
Mounting SOLEYA/SOLEYA protect - over-glass
Installation pull cords
The installation and removal of the pull cords should be performed by two
persons.
Do not twist the pull cords!
To release the pull cord fasteners, remove the small plugs (6) from the
carriages (2) and relieve the strain on the pull cords by pulling them in the
direction of the drop profile. Insert a screwdriver into the opening of the
carriages and press them down. The pull cord is now released and can be
carefully lowered. Close the opening by means of a plug again.
The pull cords are under tension.
Installing the guide rail end caps
After attaching the pull
cords, put the guide rail
end cap (1) on the guide
rail.
Secure the guide rail end
cap by screwing down the
threaded pins (2).
Legend
Guide rail end cap
Threaded pin M8
1
2

Installation Instructions and Instructions for Use
Subject to technical modifications. –Date of Issue March/2021
67
Mounting SOLEYA/SOLEYA protect - over-glass
Securing the box to the guide rail
Secure the box on the
guide rails (2).
To do this, tighten
the
threaded pin (3) that is
already screwed into the
tab (1) of the side part.
Legend
Tab of the side part (protrudes into
the guide groove of the guide rail)
Guide rail
Threaded pin M8
1
3
2
1
2
3
Installation Instructions and Instructions for Use
68
Subject to technical modifications. –Date of Issue March/2021
Mounting SOLEYA/SOLEYA protect - over-glass
Installing the anti-lift device
Slide the slot stones (1) into
the groove of the guide rails
(2). Then screw one clamping
part on the spring side (3) and
one clamping part on the
clamping side (4) per unit to
the slot stones. Use the
provided fastening screws (5).
Push the pressure spring (7)
into the side hole of the
clamping part (3). Then thread
the wire cable (6) (with
pressed-on sleeve) through the
clamping part (3). Cut the wire
to the appropriate length and
mount the threaded fitting (8)
on it. To do this, insert the
cable into the fitting as far as it
will go and clamp it with the
two threaded pins.
Screw the threaded fitting (8)
into the clamping part (4). This
tensions the cable.
Fix the fitting by tightening the
hexagon nut.
Mount anti-lift devices only
over guiding tubes!
Legend
Sliding block
Cylinder head screw M8x18
Guide rail
Wire cable with pressed-on clamping
sleeve
Clamping part (spring side)
Pressure spring
Clamping part (clamping side)
Threaded fitting M8
=
=
1
2
3
4
5
3
6
7
8
4
8
Installation Instructions and Instructions for Use
Subject to technical modifications. –Date of Issue March/2021
69
Mounting SOLEYA/SOLEYA protect - over-glass
Installing the anti-lift device
The anti-lift device (1) may
only be
mounted directly
above a guiding tube (2).
Tensioning the wire cable
can otherwise cause the
guide rails to be pulled
together. This can impair
the functioning of the unit.
The double guide rail (for
unit combinations/linkage)
has no guide grooves for
the sliding blocks on the
top side. The clamping
parts must therefore be
fixed to the double guide
rail (3) with drilling screws
(4).
Legend
Anti-lift device
Guiding tube
Double guide rail
Self drilling head screw 4.8x22 mm
Washer 06
1
2
3
4
5
Installation Instructions and Instructions for Use
70
Subject to technical modifications. –Date of Issue March/2021
Mounting SOLEYA/SOLEYA protect - over-glass
Mounting the guiding tube/guiding tube support
Attach the guiding tube holder
(1) to the guide rail (4). To do
this, push the slot nuts (2) into
the groove of the guide rail and
screw the guiding tube holder to
the slot nuts using the screws
(3) supplied.
Make sure that the guiding tube
holder has the same distance to
the outer edge of the guide rail
on the left and right guide rails.
Place the guiding tube (5)
between the guide rails and
screw it to the guiding tube
holders.
Guiding tube support
When the guiding tube has
been moved to the desired
position, align the supplied
guiding tube support (7) to the
guiding tube according to the
structure of the conservatory
and mark the fixing position on
the conservatory as well as on
the guiding tube.
Legend
Guiding tube holder
Sliding block
Cylinder head screw M8x40
Guide rail
Guiding tube
Cylinder head screw M10x55
Guiding tube support
1
2
3
4
5
6
7
=
=

Installation Instructions and Instructions for Use
Subject to technical modifications. –Date of Issue March/2021
71
Mounting SOLEYA/SOLEYA protect - over-glass
Mounting the guiding tube/guiding tube support
Legend
Guiding tube support
Guiding tube
Countersunk drilling screw
3.9x13 mm
Guiding tube distribution
(1 guiding tube)
Guiding tube distribution
(2 guiding tubes)
Attach the guiding tube support
(1) to the marked position on the
guiding tube (2). To do this, use
the provided drilling screws (3).
The guiding tube may have to be
removed again for this purpose)
Then screw the base plate of the
guiding tube support to the
conservatory. Use the
appropriate mounting material
(see mounting sets).
Guiding rails distribution
1
2
3
==
== ~800-1000
5
4
Installation Instructions and Instructions for Use
72
Subject to technical modifications. –Date of Issue March/2021
Mounting SOLEYA/SOLEYA protect - over-glass
Mounting the box support
Mount the supplied box support
(1) according to the structure of
the conservatory (2), but
preferably in the middle of the
unit. After mounting the box (3),
the box rests on the box support
and thus does not sag. To attach
the box support to the
conservatory, use the
appropriate mounting material
(see mounting sets).
Legend
Box support
Structure (observatory)
Box
1
2
3
12
Installation Instructions and Instructions for Use
Subject to technical modifications. –Date of Issue March/2021
73
Aligning the over-glass awning
Single units
Legend
Diagonal dimension
Width
Measure again the diagonal
(1) and the width (2).
The diagonal dimension as
well as the width dimensions
must be equal.
If the diagonal/width is not
correct, loosen the screws (I
+ III) of the mounting
brackets and move the
awning to the correct
dimension.
Afterwards, tighten the
screws.
2
2
1
1
I
I
I
I
I
II
Installation Instructions and Instructions for Use
74
Subject to technical modifications. –Date of Issue March/2021
Aligning the over-glass awning
Linked units
When aligning, remember
that there should be a gap of
8 mm between the guide rail
(4) and the front rail (5) on
the right and left over the
entire length of the front rail.
Legend
Diagonal dimension
Width 1
Width 2
Guide rail
Front rail
I
I
I
I
I
I
1
3
3
2
2
1
4
5
8

Installation Instructions and Instructions for Use
Subject to technical modifications. –Date of Issue March/2021
75
Installation/wiring LED
(for LED in box and guide rails)
View: Box in delivery condition
View: Box with mounted guide rails (LED in box and guide rails)
When delivered, the supply cable (2) for the LED control unit and the connection cables
(with STAK2) for the LED strips protrude from the roof profile (1). Depending on the order,
there can be up to three such connection lines (3/4/5). If the guide rails are mounted, 3
more cables (with STAS2) are added to the box. These are the connecting cables of the
LED strips from the two guide rails (7/8) and the floor/box profile (6).
Legend
Roof profile
Connection cable for LED box
LED control unit supply cable
Connection cable LED strip box
Connection cable LED GR right
Connection cable LED strip GR left
Connection cable LED GR left
Connection cable LED strip GR right
3
1
2
45
8
6
7
Installation Instructions and Instructions for Use
76
Subject to technical modifications. –Date of Issue March/2021
Installation/wiring LED
(for LED in box and guide rails)
Detail cable outlet LED in box
Detail cable outlet LED in guide rail
With LED in the boxthe
cable of the LED strip (6)
comes out of the groove of
the floor profile (9).
With LED in the guide
railthe cable of the LED
strip (7/8) comes out
between the side part (10)
and the floor profile (9).
When installing the guide
rails, make absolutely sure
that the cable of the LED
strip is not damaged or
crushed and thread it
carefully out through the
gap between the side panel
and the floor profile.
Put the Hirschmann connectors
together and stow them in the roof
profile
Now connect the
connection cables of the
LED control unit (STAK2)
with the connection cables
of the LED strips (STAS2).
To do this, plug the
Hirschmann connectors
together.
Then slide the Hirschmann
connectors into the
compartment of the roof
profile where the LED
control unit is also stowed.
6
9
78
9
10
Installation Instructions and Instructions for Use
Subject to technical modifications. –Date of Issue March/2021
77
Installation/wiring LED
(for LED in box and guide rails)
Tighten the cables of the
LED strips and the cable of
the LED control unit and fix
them with cable ties (11) on
the side panel (12).
The side part (12) has
recesses (13) where the
cable ties can be threaded
through.
Legend
LED control unit cable
Cable ties
Side part
Recesses for cable ties
With combined units, it is
necessary to remove the
roof profile for wiring the
LED strips.
11
11
11
12
2
13
13
13
Installation Instructions and Instructions for Use
78
Subject to technical modifications. –Date of Issue March/2021
Malfunctions
What is the matter, if...
... the front rail moves to the awning box
askew?
The awning(s) was/were not diagonally
aligned during installation.
Solution: Measure the
diagonal as described in
Chapter “Aligning the
underglass awning” and align
the awning accordingly.
The tension on the right side or guide rail is
too high or too little on the left side or guide
rail.
Solution: Check the tension
as described in Chapter
“Installation of the pull cords”.
The awning cover is sewn askew.
Solution: Place a small cover
remnant underneath the right
outer seam of the awning
cover. For this purpose it is
necessary to completely
extend the awning. This has
the effect that the awning
cover rolls up slightly thicker
and brings the front rail closer
to the awning box.
The spring mechanics on the left side is
defective.
Solution: Loosen the pull
cord on the left side. Try to
turn the tape pulley. If the
tape pulley cannot be turned
at all or very easily, the spring
mechanics is defective and
must be replaced.