Hewlett Packard Enterprise Edgeline EL8000 User manual

HPE Edgeline EL8000 Converged Edge
System Setup and Configuration Guide
Part Number: P12853-001
Published: August 2019
Edition: 1
Abstract
This document is for the person who installs, administers, and troubleshoots servers and storage
systems. Hewlett Packard Enterprise assumes you are qualified in the servicing of computer
equipment and trained in recognizing hazards in products with hazardous energy levels.
HPE Confidential

Notices
The information contained herein is subject to change without notice. The only warranties for Hewlett Packard
Enterprise products and services are set forth in the express warranty statements accompanying such
products and services. Nothing herein should be construed as constituting an additional warranty. Hewlett
Packard Enterprise shall not be liable for technical or editorial errors or omissions contained herein.
Confidential computer software. Valid license from Hewlett Packard Enterprise required for possession, use,
or copying. Consistent with FAR 12.211 and 12.212, Commercial Computer Software, Computer Software
Documentation, and Technical Data for Commercial Items are licensed to the U.S. Government under
vendor's standard commercial license.
Links to third-party websites take you outside the Hewlett Packard Enterprise website. Hewlett Packard
Enterprise has no control over and is not responsible for information outside the Hewlett Packard Enterprise
website.
Acknowledgments
Intel®, Itanium®, Pentium®, Xeon®, Intel Inside®, and the Intel Inside logo are trademarks of Intel Corporation in
the U.S. and other countries.
Microsoft® and Windows® are either registered trademarks or trademarks of Microsoft Corporation in the
United States and/or other countries.
Adobe® and Acrobat® are trademarks of Adobe Systems Incorporated.
Java® and Oracle® are registered trademarks of Oracle and/or its affiliates.
UNIX® is a registered trademark of The Open Group.
HPE Confidential

Overview
The HPE Edgeline EL8000 Converged Edge System is designed to help communication service providers
capitalize on data-intensive, low-latency services for media delivery, connected mobility, and smart cities. With
the ability to process the increasing amount of data in real time directly at the edge, the system boosts
flexibility and reduces costs by using open standards. By reducing the need for proprietary edge systems, the
HPE EL8000 enables enhanced performance and versatility for data-intensive real-time digital services while
providing a compact, ruggedized design, modular blade and chassis options, and even one-click provisioning
and remote system management.
The HPE EL8000 Chassis Manager is a remote management tool embedded in certain HPE Edgeline
systems. The software allows system administrators to remotely configure, update, and monitor chassis
health and activity. The embedded EL8000 CM management module has its own network connection and IP
address to which administrators connect on their dedicated management network. Depending on hardware
configuration, HPE Edgeline systems with the EL8000 CM can be connected to a management network using
Ethernet or a wireless Wi-Fi connection. The EL8000 CM offers both a Web-based console (GUI) and a
command line interface (CLI).
This guide includes setup and configuration information for the HPE EL8000 chassis. See <link to e910 setup
guide> for information related to the ProLiant e910 blade setup, configuration, and operating system
installation.
HPE Confidential Overview 3

Setup and configuration
Checklist
Complete this checklist to set up, install, and configure your new HPE Edgeline EL8000 Chassis Manager
1.0.
1. Unbox the system and identify the components.
2. Verify that the intended installation site conforms to space, airflow, temperature, and power
requirements.
3. Install applicable hardware option:
Front bezel option
4. Install one or more blades in the chassis if necessary.
5. Determine the rack depth compatibility of the system, and then install it in a rack:
•Two-post rack
•Four-post rack
6. Prepare to configure the system:
a. Verify network connectivity.
b. Plan for network address.
7. Connect to the Edgeline EL8000 Chassis Manager and configure the system using one of the
available methods:
•Connect using the WiFi Access Point.
•Connect to the Edgeline EL8000 Chassis Manager web interface.
•Connect to the Edgeline EL8000 Chassis Manager CLI using serial cable.
8. Register your system with HPE.
TIP: Did you know that HPE has QR codes on all systems? Scan one to access important information
on your mobile device:
Not interested is scanning the QR code? Click the following link to access the mobile pages for quick
setup, maintenance, and troubleshooting information:
http://www.hpe.com/qref/el8000
4 Setup and configuration HPE Confidential

Planning the installation
Safety and regulatory compliance
For safety, environmental, and regulatory information, see Safety and Compliance Information for Server,
Storage, Power, Networking, and Rack Products, available at the HPE website (http://www.hpe.com/
support/Safety-Compliance-EnterpriseProducts).
Site requirements
Before installing the system, verify that the following site requirements are met:
• Space and airflow requirements
• Temperature requirements
• Power requirements
HPE recommends that you install or position the system in a location with restricted access, where the access
is secured and controlled. The users/technicians handling the system should be informed about the
restrictions applied and precautions to be taken.
Space and airflow requirement
To allow for servicing and adequate airflow, leave a minimum clearance of 20 cm (7.9 in.) around the system.
Power requirement
Installation of this equipment must comply with local and regional electrical regulations governing the
installation of information technology equipment by licensed electricians. This equipment is designed to
operate in installations covered by NFPA 70, 1999 Edition (National Electric Code) and NFPA-75, 1992 (code
for Protection of Electronic Computer/Data Processing Equipment). For electrical power ratings on options,
see the product rating label or the user documentation supplied with that option.
Temperature requirements
To ensure continued safe and reliable equipment operation, install or position the system in a well-ventilated,
climate-controlled environment.
Configuration Temperature
Chassis with blades installed Operating temperature of up to 55°C (131°F)
HPE Confidential Planning the installation 5

Component identification
This chapter describes the external and internal server features and components.
System components
Item Description
1 EL8000 Converged Edge Chassis
2 Midplane assembly
3 Fan assembly
4 Server tray
5 Chassis manager
6 Power supplies
HPE Edgeline EL8000 Converged Edge system
EL8000 system with 1U server blades installed
The EL8000 system can accommodate up to four 1U HPE ProLiant e910 server blades.
6 Component identification HPE Confidential

EL8000 system with 2U server blades installed
The EL8000 chassis can accommodate up to two 2U HPE ProLiant e910 server blades.
Power supply LEDs
• AC power supply
HPE Confidential Component identification 7

Status Description
Solid Green System On and normal operation
Flashing Green Standby power present (power supply off)
Solid Amber Power supply failed (overvoltage/undervoltage,
overtemperature, overcurrent, short-circuit), fan
failed, or input overvoltage protection
Flashing Amber Power supply error
Off No power present or standby power failed
(overvoltage/undervoltage, overtemperature,
overcurrent, short-circuit, fan lock)
• DC power supply
Status Description
Solid Green System On and normal operation
Flashing Green Standby power present (power supply off)
Solid Amber Power supply failed (overvoltage/undervoltage,
overtemperature, overcurrent, short-circuit), fan
failed, or input overvoltage protection
Flashing Amber Power supply error
Off No power present or standby power failed
(overvoltage/undervoltage, overtemperature,
overcurrent, short-circuit, fan lock)
8Component identification HPE Confidential

Chassis manager components
Item Description
1 Management Network port
2 Blade maintenance network port
3 Antenna 1
4 Chassis manager USB ports
5 Antenna 2
6 Chassis UID Button/LED
7 Chassis Health LED
HPE Confidential Component identification 9

Rack mount option
There are two rack options available for installing the EL8000 chassis:
• Two-post rack mount option
• Four-post rack mount option
Mounting rails on the two-post rack
The two-post rack is available in 19 in and 23 in depth.
Prerequisites
Before you perform this operation, make sure you have the following items available:
• Phillips screwdriver
• M2, M5 Screwdriver
Procedure
1. Install the brackets on rack columns.
When installing the rail kit on 19 in rack columns, remove the outer brackets and install only the inner
brackets.
2. Loosen the screws on each bracket, so as to enable them to move freely.
10 Rack mount option HPE Confidential

3. Install the rack tray into the brackets:
a. Install the tray into the brackets.
b. Install two M5 screws in the front and rear brackets each, and then tighten them.
HPE Confidential Rack mount option 11

c. Tighten the eight screws that were loosened in step 2.
4. Install the chassis on the rack tray:
a. Place the chassis on the rack tray.
b. Secure the chassis with two M5 screws on the front.
12 Rack mount option HPE Confidential

c. Secure the chassis with two M5 screws on the rear.
Mounting the rails on the four-post rack
Prerequisites
Before you perform this operation, make sure you have the following items available:
• Phillips screwdriver
• M2, M5 Screwdriver
Procedure
1. Identify the mounting location, install the tray bracket and stop the screw in correct location.
HPE Confidential Rack mount option 13

2. Install the rails into the rack.
3. Install the rack tray on the rails and secure it.
Make sure that the tray slides under the bracket.
14 Rack mount option HPE Confidential

4. Place the chassis in the tray and secure it.
HPE Confidential Rack mount option 15

Hardware options installation
This chapter provides detailed instructions on how to install hardware options.
For more information on supported options, see the product QuickSpecs on the website at:
http://www.hpe.com/info/qs
To view the warranty for your server and supported options, see Warranty information on page 34.
Front bezel option
This option is available only for reverse airflow chassis.
Installing the bezel
Procedure
Install the bezel.
16 Hardware options installation HPE Confidential

Associated hardware procedures
This chapter describes the hardware operations carried out prior to and after installing or removing a
hardware option, or performing system maintenance or troubleshooting.
Before performing these hardware operations, review and observe system warnings and cautions.
Power down the system
Before powering down the system for any upgrade or maintenance procedures, back up critical system data
and programs.
Before performing chassis maintenance, shut down all blades installed in the system.
Procedure
• Use one of the following methods to power down the system:
◦ Press and release the Power On/Standby button of the blades installed in the system.
This method initiates a controlled shutdown of applications and the OS before the system enters
standby mode.
◦ Press and hold the Power On/Standby button of the blades installed in the system for more than 4
seconds to force the system to power down.
This method forces the system to power down without properly exiting applications and the OS. If an
application stops responding, you can use this method to force a shutdown.
Verify the system is in standby mode and the system power LED is amber.
Power up the system
If the system is connected to a power source, it powers up automatically by default. Generally, it has to be
powered up only after a manual shutdown. However, using iLO, blades can be individually configured to not
power up automatically.
Procedure
• Use one of the following methods to power up the system:
◦ Press the Power On/Standby button of the blade installed in the system.
◦ Remotely power up the system through iLO.
Removing the blade from the chassis
Procedure
1. Power down the system.
2. Press the blade latch and open the latch.
3. Remove the blade.
HPE Confidential Associated hardware procedures 17

Installing the server blade into the chassis
Procedure
Align the blade and install it in the chassis.
18 Associated hardware procedures HPE Confidential

Configuration
Quick task: Be prepared
TIP: Gather all the materials and information
you need before getting started.
“What do I need to know before I start configuring my
Edgeline EL8000 Chassis Manager?”
Make sure you can get an
Internet connection and a
business network
connection.
Not using DHCP? Plan your network addressing
scheme before starting to configure the system.
Prepare for configuration
Prepare to configure your new system by completing the tasks below.
1. Verify network connectivity
Ensure that the network connection is active, if needed.
2. Verify Internet connectivity
Verify Internet access from your business network. Make a note of the gateway IP address, you may need
it later.
3. Plan for the network address
If you do not have DHCP enabled on the network, you must have networking details ready: An IP address
to assign, subnet mask, gateway address, and DNS name. For initial setup, it is faster to allow automatic
assignment of these details by connecting your system to a DHCP enabled network.
Connecting to Edgeline EL8000 Chassis Manager the first
time
Once the system is unboxed, connected to your management network, and powered up, there are a few
options for accessing Edgeline EL8000 Chassis Manager the first time. You can initially configure Edgeline
EL8000 Chassis Manager by connection to:
• The Edgeline EL8000 Chassis Manager web interface using the WiFI access point (WiFi AP).
• The Edgeline EL8000 Chassis Manager web interface through the management network.
• The Edgeline EL8000 Chassis Manager CLI using a DB9 null modem serial cable and a USB-to-RS232
adapter, and retrieving the DHCP assigned IP address or hostname.
Connecting to the web interface using the WiFi Access Point
HPE recommends this method for initial configuration.
HPE Confidential Configuration 19

Prerequisites
• Username and password noted from the chassis tag
• WiFi-enabled laptop or mobile device
Procedure
1. Search for available WiFi connections on your device.
The WiFi SSID starts with EL8000CM, followed by a ten-digit alphanumeric serial number. The letters and
numbers are the DNS Name printed on the Chassis Tag. For example, EL8000CMMXQ92305J4.
2. Select the WiFi connection and then enter the username and password.
3. After you connect to the WiFi, the message prompt Logging into WiFi appears for a while and the
login page for Edgeline EL8000 Chassis Manager is displayed. Log in with the credentials printed on the
chassis tag.
If the message prompt does not appear, open a browser window to 192.168.37.1 to access the Edgeline
EL8000 Chassis Manager login page.
Connecting to the web interface using Ethernet
When your setup devices are not WiFi-enabled, acquire the IP address or hostname through your
management network.
Prerequisites
• System hardware unboxed, installed, and powered up
• Username and password noted from the chassis tag
• Ethernet cable
• DHCP enabled network
Procedure
1. Connect an Ethernet cable between the MGMT port on the system chassis and your management
network.
2. Wait for the hostname of your new system to propagate onto your network through DDNS and have an IP
address assigned through DHCP.
3. On a separate computer connected to your network, enter the address https://<iLO hostname or
IP address> in a browser window. HTTPS (HTTP exchanged over an SSL encrypted session) is
required for accessing the Edgeline EL8000 Chassis Manager web interface.
To use the hostname, enter the fully qualified domain name (if your computer is outside the domain) or just
the hostname (if your computer is inside the domain).
4. Log in with the default credentials listed on the system chassis tag.
Connecting to the CLI in a serial session
If ICMP ping or other tools are disabled on your management network, retrieve the IP address in a serial
session.
20 Configuration HPE Confidential