HIK VISION DS-K5604A-3XF Series User manual
DS-K5604A-3XF Series
Face Recognition Terminal
Quick Start Guide
UD19290B-F
Model Manufacturer Standard
GroundBottom Cover
Bracket
Bottom Screw
M6×65 Expension Bolt
1
23
Before you start: Make sure the ground surface has drilled
holes for device installation.
Steps:
1. Remove the two bottom screws (2-SC-KM3×5B-JMF) on
both sides of the bottom cover. And remove the bottom
cover.
2. Align the device with the drilled holes on the ground and
insert 3 supplied expension bolts (M6×65). Make sure the
expension bolts are higher than the ground.
3. Secure the expension bolts with nuts。
4. Install the bottom cover back on the device with 2 bottom
screws.
5. After installation, for the proper use of the device (outdoor
use), stick the protection film (parts of models supplied) on
the screen.
The actual device
appearance varies
according to
different models.
The device should be installed on the concrete surface or other
non-flammable surfaces.
The device supports plug & play. You can put the device on the
ground and start operation after powering on.
2Installation
The wiring diagram of RS-485 and Door Lock on the left is shown below:
1Appearance
3.1
Device Wiring (Normal)
165 mm
1398.95 mm
172 mm
250.71 mm
46 mm
144.71 mm
37 mm
185.91 mm
1347.28 mm
Touch Screen
IR Light IR Light
Camera
White Light
Thermographic
Module
69.96 mm
Installa�on Environment:
Temperature Measurement Environment:
Wind:
Sweat:
Air Condi�oner (Cool Air):
Air Condi�oner (Heat) or Hea�ng:
BTN Door Contact
(NC)
(COM)
(NO)
Power
Switch
USB Interface
Power
Interface
Door Lock
Interface
RS-485
Interface
Network
Interface
(Reserved)
Network
Interface
When connecting door contact and exit button, the device and
the RS-485 card reader should use the common ground
connection.
The suggested external power supply for door lock is 12 V, 1A.
Positions When Collecting/
Comparing Face Picture
(Recommended Distance: 0.5m)
Tips When Collecting/
Comparing Face Picture
Expression
Posture
Size
Correct Tilt RaiseSide Bow
Correct Too Close Too Far
6Add Face Picture
Temperature Measurement Settings
5
Enable Temperature Detec�on:
Over-Temperature Alarm Threshold:
。
Temperature Compensa�on:
Door Not Open When Detec�ng Abnormal Termperature:
Temperature Measurement Only:
Unit:
3.2 Device Wiring (With Secure Door Control Unit）
NO
NC
COM
NC
NO
COM
4
Steps:
Ac�vate
Activation via Device Steps Afterwards
Face
www.recyclethis.info
www.recyclethis.info
Other manuals for DS-K5604A-3XF Series
1
Other HIK VISION Touch Terminal manuals
HIK VISION
HIK VISION DS-K1T642 Series User manual
HIK VISION
HIK VISION DS-MDH005-B User manual
HIK VISION
HIK VISION DS-TPE100 User manual
HIK VISION
HIK VISION Ultra Series User manual
HIK VISION
HIK VISION K1T671 User manual
HIK VISION
HIK VISION DS-KH9510-WTE1 User manual
HIK VISION
HIK VISION DS-K1A801MF User manual
HIK VISION
HIK VISION DS-K1T802E User manual
HIK VISION
HIK VISION DS-K5604A-3XF/V User manual
HIK VISION
HIK VISION DS-K1T320 Series User manual
HIK VISION
HIK VISION DS-TPW332-C User manual
HIK VISION
HIK VISION UD19294B User manual
HIK VISION
HIK VISION DS-K1A8503 Series User manual
HIK VISION
HIK VISION DS-K1TA70 Series User manual
HIK VISION
HIK VISION DS-K1A802A Series User manual
HIK VISION
HIK VISION DS-K1T341BMWI-T User manual
HIK VISION
HIK VISION DS-K1T671 Series User manual
HIK VISION
HIK VISION DS-TPM400 Series User manual
HIK VISION
HIK VISION DS-K5671-3XF/ZU User manual
HIK VISION
HIK VISION DS-K5032 Series User manual
