HOMCOM A90-144 User manual

Spinning Bike
Instruction Manual
A90-144

Content
Safety Information
Components – Parts
Assembly Instructions
Computer Operation
Exercising Information
Care and Maintenance

Safety Information
Important –Please read fully before assembly or using
Assembly
• Check you have all the components and tools listed, bearing in mind that, for ease of
assembly, some components are pre-assembled.
• Keep children and animals away from the work area, small parts could choke if swallowed.
• Make sure you have enough space to layout the parts before starting.
• Assemble the item as close to its final position (in the same room) as possible.
• Position the equipment on a clear, level surface.
• Dispose of all packaging carefully and responsibly.
Using
• It is the responsibility of the owner to ensure that all users of this product are properly
informed as to how to use this product safely.
• This product is intended for domestic use only.
Do not use in any commercial, rental, or institutional setting.
• Before using the equipment to exercise, always do stretching exercises to properly warm
up.
• If the user experiences dizziness, nausea, chest pain, or other abnormal symptoms stop
the workout and seek immediate medical attention.
• Only one person at a time should use the equipment.
• Keep hands away from all moving parts.
• Always wear appropriate workout clothing when exercising. Do not wear loose or baggy
clothing, since it may get caught in the equipment. Wear athletic shoes to protect your feet
while exercising.
•Do not place any sharp objects around the equipment.
• Disabled persons should not use the equipment without a qualified person or doctor in
attendance.
• This product is suitable for user’s weight of 110kgs.

Components – Parts
1.pedal 7.handle 13. knob 19. corrugated pipe
2. monitor 8.screw M8 14. Screw nut
3. 8*75 carriage bolt 9. Ф8 washer 15.saddle
4. Ф8 arc pad 10. rear tube 16. brake
5. Ф6 washer 11. front tube 17. handle support
6. Cylinder head screw M6 12. crank 18. flywheel

Installation Instruction
1) Connect the front tube with the frame, and fix by the plain washer 8, washer 8 and the
cover-shaped screws. Installation of back tube is the same.
Note: Please adjust the black feet strap to make it balance if it is not stable.
2) The pedals are marked with L and R. Please fasten the pedal with right threaded hole by
using the spanner and fix it tight with the built-in nut. And fasten the pedal with left
threaded hole by using the spanner and fix it tight with the built-in nut.
(Note: L and R are marked in crank as well. Please install them accordingly otherwise it will
damage the products. And please fasten the feet strap, or it will fall down after long usage.)

3）Take out the handle and fix it into the support by screws and washers..
3) 1. Slide the monitor onto the groove
2. Connect the cables as A. (only for model without pulse function)
3. Double wire with right Pulse and single wire with left sensor. Please keep the messy
cables inside the pipe as B. (only for model with pulse function)
5) Loose the knob A and B to adjust the position of the cushion. And fasten the knob to fix
the cushion. (The cushion can be adjusted front/ back, up/ down.)

6) Rotate the break knob clockwise to increase the resistance and rotate the break knob
anticlockwise to decrease the resistance. Press down the break knob for emergency stop.
Computer Operation
Time................................................................................00-00—99：59 Minute: Second
Speed .............................................................................00—99.9 km/h
Distance..........................................................................0.00—99.99 Km
Odometer........................................................................0.00—999.9 Km
Heart Rate......................................................................40—240BPM(Optional)
Calorie............................................................................ 0.999.9Kcal
MODE: This key lets you select and lock on to a particular function which you want.
Press to Choose SCAN or LOCK, if you do not want the scan mode, press the Mode
key until the pointer is next to the “flashing” function which you want.
AUTO ON /OFF：The monitor will switch on automatically when the exercise
machine is in motion. The monitor will turn off automatically when the speed has no
signal input or no keys are pressed for approximately 4 minutes.
RESET: The unit can be reset by either changing the battery or pressing the MODE
key for 3 seconds.
SPEED: Press Mode key until the pointer advances to SPEED. The Computer will
display the current speed.
DISTANCE: Press Mode key until the pointer advances to DIST. The Computer will
display each trip distance you have traveled.
TIME: Press Mode key until the pointer advances to TIME. The total working time will
be shown when starting exercise.
CALORIES: Press Mode key until the pointer advances to CAL. The Computer will
display total calories burns when starting to exercise.
ODOMETER：Press the MODE Key until the pointer advance to ODOMETER. The total
accumulated distance will be shown.
Exercising Information

Each workout should include the following three parts:
1. A warm-up, consisting of 5 to 10 minutes of stretching and light exercise. A proper
warm-up increases your body temperature, heart rate, and circulation in preparation for
exercise.
2. Training zone exercise, consisting of 20 to 30 minutes of exercising with your heart rate in
your training zone. (Note: During the first few weeks of your exercise program, do not keep
your heart rate in your training zone for longer than 20 minutes.)
3. A cool-down, with 5 to 10 minutes of stretching. This will increase the flexibility of your
muscles and will help to prevent post-exercise problems.
Exercise Frequency
To maintain or improve your condition, plan three workouts each week, with at least one day of
rest between workouts. After a few months of regular exercise, you may complete up to five
workouts each week, if desired. Remember, the key to success is make exercise a regular
and enjoyable part of your everyday life before starting to exercise
Care and Maintenance
1. Examine the equipment periodically in order to detect any damage or wear which may
have been produced.
2. Lubricate moving parts with light oil periodically to prevent premature wear.
3. Inspect and tighten all parts before using the equipment, replace any defective parts
immediately, and do not use the equipment again until it is in perfect working order.
4. The equipment can be cleaned using a damp cloth and mild non-abrasive detergent.
Do not use solvents.
5. Do not attempt to repair this equipment yourself. Should you have any difficulty with
assembly, operation or use of your exercise product or if you think that you may have parts
missing, contact the manufacturer.
Guarantee:
For guarantee purposes, please retain your purchase receipt.