Home Styles 5004 692 User manual

Hardware List
Part List
Home Styles Customer Service: www.homestyles-furniture.com,
[email protected], 888-680-7460, 877-831-0319
Tool(s) required for assembly: Phillips screwdriver, Level, Drill (8 volts or less), 3/8” Drill Bit
5004 692-
Pantry
IMPORTANT
Carefully remove all the parts from the carton and
place them individually on a soft cloth to prevent
scratches or other damage.
Carefully and strictly follow these assembly instructions
to ensure a completed product as designed.
Do not use power tools above 8 volts to assemble.
Cam Lock Screw
24 pcs. (+1 extra)
Cam Lock
24 pcs. (+4 extra)
M3.5x16
Wood Screw
16 pcs. (+1 extra)
Adjustable Pin
16 pcs. (+1 extra)
Knob
4 pcs.
M4x25
Machine Screw
4 pcs.
A.
Top
1 pc.
B.
Side Panel
2 pcs.
C.
Side Panel
2 pcs.
D.
Back Stretcher
4 pcs.
E.
Back Upright
2 pcs.
F.
Back Panel
4 pcs.
G.
Middle Panel
1 pc.
H.
Base
1 pc.
I.
Shelf
4 pcs.
J.
Door
2 pcs.
K.
Door
2 pcs.

Assembly Instructions 2/6
IMPORTANT
Use a soft cloth between these parts and the floor.
Do not use power tools above 8 volts to assemble.
Make sure unit is level before tightening these screws.
The unit must be level to work properly. Use the included adjustable levelers to level.
Figure 1
STEP 1
Insert Cam Lock Screws into
pre-drilled holes in Top (A),
Side Panels (B), (C), Middle Panel (G)
and Base (H), then tighten.
(See Figure 1)
A
B
C
G
H
Cam Lock Screw
Cam Lock Screw
Cam Lock Screw
Cam Lock Screw

Assembly Instructions 3/6
Figure 2
STEP 2
Attach Back Stretcher (D) to
Side Panel (B) with Cam Lock.
(See Figure 2)
Attach Back Upright (E) to
Stretcher (D).
Slide Back Panels (F) into position.
Attach Back Stretcher (D)
to unit with Cam Lock.
Attach Side Panel (C)
to unit with Cam Locks.
STEP 3
Attach unit to Base (H)
with Cam Locks.
Attach Doors (J) and (K) to unit
by sliding door hinges into
side panel hinges. (See Figure 3)
Attach Middle Panel (G) to unit
with Cam Locks.
H
G
J
K
Cam Lock
Cam Lock
Figure 3
D
FF
E
D
B
C
Cam Lock
Cam Lock

Assembly Instructions 4/6
STEP 5
Attach unit from Step 4 to unit from Step 3
with Cam Locks.
Cam Lock
STEP 4
Attach Back Stretcher (D) to
Side Panel (B) with Cam Lock.
(See Figure 2)
Attach Back Upright (E)
to Stretcher (D).
Slide Back Panels (F)
into position.
Attach Back Stretcher (D)
to unit with Cam Lock.
Attach Side Panel (C)
to unit with Cam Locks.
D
FF
E
D
B
C
Cam Lock
Cam Lock

Assembly Instructions 5/6
STEP 6
Insert Adjustable Pins into
side panels at desired level.
Place Shelves (I) into position.
Attach Doors (J) and (K) to unit by sliding
door hinges into side panel hinges.
Attach Knobs to Doors (J) and (K) with
Machine Screws. (See Figure 4)
Attach Top (A) to unit with Cam Locks.
STEP 7
Level unit by adjusting the adjustable levelers
on bottom of unit. (See Figure 5)
Note: Unit must be level to proceed.
Insert Wood Screws into pre-drilled holes in unit,
then tighten.
Note: Unit must be level before
tightening these screws.
Figure 4
Cam Lock
Figure 5
Adjustable Pin
Knob
Machine Screw
Wood Screw
Adjustable Pin
A
I
I
JK
I
I
J K

Assembly Instructions 6/6
Hardware List
STEP 8
Place unit at desired location.
Drill a 3/8” hole in wall in-line with
pre-drilled hole at top of unit.
Move unit.
Insert Anchor into the wall hole
and attach Bracket with Wall Screw.
Attach Bracket at pre-drilled hole
at top of unit with Wood Screw.
Move unit back into place.
Slide Tipover Restraint through
Bracket on wall and Bracket on unit.
(See Figure 6)
Put tie end of Tipover Restraint into lock
end of Tipover Restraint and pull until tight.
Anchor
1 pc. (+1 extra)
Bracket
2 pcs. (+1 extra)
Tipover Restraint
1 pc. (+1 extra)
M3.5x40
Wall Screw
1 pc. (+1 extra)
M3.5x16
Wood Screw
1 pc. (+1 extra)
Figure 6
Wood Screw
Wall Screw
Bracket
on wall
Anchor in wall
3/8” wall hole
Pre-drilled hole
at top of unit
Tie end
Lock end
Bracket at
top of unit
Tipover
Restraint
IMPORTANT
To help reduce the risk of the unit tipping over, the Tipover Restraint must be installed following these instructions exactly.
Drill 3/8” hole in wall
Top of unit

NEVER
use glass cleaners on
finished furniture. Ammonia
chemically attacks the finish.
allow liquids to remain on furniture.
Absorption causes parts to warp
and split and finishes to delaminate.
NEVER
CARE INSTRUCTIONS
Do not use rubber
based placemats.
PREVENT
DISCOLORING
Do not use commercial
waxes and polishes.
PREVENT
YELLOWING
Do not place hot
objects on surface.
PREVENT
FINISH DAMAGE
Do not write
directly on surface.
PREVENT
MARKING
Do not use power tools
above 8 volts to assemble.
PREVENT
CRACKING
Do not place
in direct sunlight.
PREVENT
FADING
with a soft cloth moistened
in lukewarm soap and water.
Buff with a dry clean cloth.
CLEAN
Home Styles will provide replacements free of charge for missing or damaged hardware or parts within 30 days of
purchase. Digital images of the defective parts may be required. If the product was not purchased from an authorized
retail affiliate, Home Styles is under no obligation to provide replacement parts. Parts are not available for fully
assembled items nor are parts available for sale. Replacements for missing or damaged hardware or parts may be
requested at:
www.homestyles-furniture.com/customer-service/replacement-parts
Home Styles Customer Service: www.homestyles-furniture.com,
[email protected], 888-680-7460, 877-831-0319