Honeywell 6280 Series User manual

6
62 28 80 0 S Se er ri ie es s
T
To ou uc ch hC Ce en nt te er r K Ke ey yp pa ad ds s
User Guide
800-07602V3 4/13 Rev. B

Table of Contents
2
ABOUT THE TOUCHCENTER ..................................................................................................................................................................5
Introduction..........................................................................................................................................................................................5
The TouchCenter Interface..................................................................................................................................................................5
Navigating through the TouchCenter............................................................................................................................................6
About Your Home Screen.............................................................................................................................................................6
Multi-Media Application ................................................................................................................................................................6
System Troubles ..........................................................................................................................................................................8
User Codes ..................................................................................................................................................................................9
Extended Functionality.................................................................................................................................................................9
LED Operation..............................................................................................................................................................................9
Safe Mode....................................................................................................................................................................................9
SECURITY ...............................................................................................................................................................................................10
Introduction to Security System Operation........................................................................................................................................10
How to Arm the System..............................................................................................................................................................11
How to Arm Multiple Partitions ...................................................................................................................................................11
How to Display Faults.................................................................................................................................................................12
How to Bypass Zones ................................................................................................................................................................12
How to Clear Bypassed Zones...................................................................................................................................................13
How to Disarm the System.........................................................................................................................................................13
To disarm Multi-Partitions do the following:................................................................................................................................14
How to Check the Status of Other Partitions..............................................................................................................................14
Fire and Carbon Monoxide Alarm Operation..............................................................................................................................15
In Case of Fire Alarm .................................................................................................................................................................15
Silencing and Clearing a Fire/Carbon Monoxide Alarm..............................................................................................................15
More Choices ....................................................................................................................................................................................16

Table of Contents
3
How to Clear/Hide a Control Panel Message.............................................................................................................................16
Advanced System Features .......................................................................................................................................................16
Console Emulation Mode ...........................................................................................................................................................17
How to View the Event Log........................................................................................................................................................17
How to Send Emergency Messages ..........................................................................................................................................18
SETUP......................................................................................................................................................................................................19
Brightness and Volume Control..................................................................................................................................................19
Display & Audio Setup................................................................................................................................................................19
Operating Modes........................................................................................................................................................................19
Language Selection....................................................................................................................................................................20
Adjust the Screen Timeouts .......................................................................................................................................................20
Clean Screen..............................................................................................................................................................................21
Routine Care..............................................................................................................................................................................21
System Information ....................................................................................................................................................................21
MULTI-MEDIA..........................................................................................................................................................................................22
Picture Setup..............................................................................................................................................................................22
Voice Messages.........................................................................................................................................................................23
USER SETUP...........................................................................................................................................................................................24
User Setup.........................................................................................................................................................................................24
Authority Levels..........................................................................................................................................................................24
Access User Setup.....................................................................................................................................................................24
How to Add a User.....................................................................................................................................................................25
How to Delete a User.................................................................................................................................................................25
How to Edit a User .....................................................................................................................................................................25
Safe Mode..................................................................................................................................................................................26
Time/Date Setup................................................................................................................................................................................27

Table of Contents
4
Setting Daylight Saving Time.....................................................................................................................................................27
Setting Current Time and Date...................................................................................................................................................27
Advanced Setup.........................................................................................................................................................................28
Keypad Test...............................................................................................................................................................................28
Keypad Reset.............................................................................................................................................................................29
GLOSSARY .............................................................................................................................................................................................30

5
About the TouchCenter
Introduction
Congratulations on your ownership of a Honeywell 6280 Series TouchCenter keypads which combines security and
home automation. You've made a wise decision in choosing it, for it represents the latest in security protection
technology today.
This security system offers you burglary protection and provides fire, carbon monoxide and emergency protection. To
realize the full potential of the system, it is important that you feel comfortable operating it.
Your system may consist of one or more of the following:
•6280S (black/silver housing)
•6280W (white housing)
•One or more other keypads for security system control
•Various sensors for perimeter and interior burglary protection, plus a selected number of strategically placed
smoke, carbon monoxide or combustion detectors
•Lighting/output devices.
The system uses microcomputer technology to monitor all zones, and provides appropriate information for display on
the TouchCenter and/or other keypads used with the system. Your system may also have been programmed to
automatically transmit alarm or status messages over the phone lines to a central alarm monitoring station.
The TouchCenter Interface
The 6280 Series graphical touch-screen keypads are Advanced User Interface (AUI) devices, which combine control
of your security system, multi-media and premises lighting. With clear, simple controls on a touch-screen interface,
the TouchCenter is both easy to learn and easy to use.
As a security and home-automation interface, the TouchCenter may be accessed for:
•Quick and easy security system operation
•Multi-Media operation
•Message storage and retrieval
•Home output control

About the TouchCenter (cont'd)
6
Navigating through the TouchCenter
Navigation through the TouchCenter typically begins from the "Home" screen. This is the TouchCenter’s main
default screen (starting screen) and is the first screen you see when the TouchCenter is powered up and initialized.
It is from this screen that you select from the main menu. Once you have made your selection, you can navigate
through various sub-menus by touching graphical icons or icons to perform the function you desire.
About Your Home Screen
Your "Home" screen is the gateway to your TouchCenter Keypad.
From this screen you can:
•control your security system,
•control your multi-media applications, and
•control the premises lighting.
Your "Home" screen is displayed most of the time and is
customizable via the Multi-Media Application.
Ready To Arm
Security Light
MultiMedia
Friday
02:46PM
01/06/2012
home_screen-V0
Multi-Media Application
The Picture feature allows you to display personal photos (in a slide show format) via the external SD/SDHC card.
It is recommended that you use the SD/SDHC card supplied with the keypad.
In everyday handling, memory cards can become susceptible to malfunction and/or failure due to electrostatic
discharges and the information on the card may be lost. In some extreme cases, the keypad may need to be reset.
NOTE: Honeywell is not responsible for any loss of personal information (files, messages, photos, etc.)
Memory Card Insertion
Insert the memory card (SD/SDHC
Card) as shown.
Tips for proper memory card handling:
•Avoid touching the contacts on the card
•Quit the slide show application before removing the memory card.
6280-004-V0
INSERT
CARD
The background and icons shown on the “Home” screen in this manual are for example only. Your system
installer may have changed the actual background and icons shown on your “Home” screen.

About the TouchCenter (cont'd)
7
Navigation Icon Descriptions
To aid in the navigation through the TouchCenter, a set of user-friendly icons has been provided. The appearance
and function of these icons are described below.
ICON ICON TITLE FUNCTION ICON ICON TITLE FUNCTION
"Light” Allows you to turn certain devices on and off (if installed and
programmed by your installer.)
“Setup” Allows access to “Setup” menus.
"Security” Accesses "Security" screen. “Multi-Media” Accesses the “Message” and
“Picture” features.
“Home” Returns you to the "Home"
screen.
“Picture” Allows user to display personal
photos in a slide show format.
“Panic” Displays Emergency functions
(as programmed by the installer).
Note: This icon is displayed and
active on all screens except while
in the Clean Screen mode and
during an LCD Display test in
Diagnostics.
"Message” Record and retrieve Voice
Messages.
“Back”
Reverts to the last screen
viewed.
“Voice Status” Allows user to hear system status.
“Control Panel
Message” This icon alerts the user to a “Control Panel Message”.
Minimizing the Home Screen Icons
When viewing wallpaper displays, the Home screen icons can be minimized by touching the “Minimize Home” icon.
Touch the “Maximize Home” icon to maximize Home screen icons. Refer to the section Picture Setup.
Minimize Home Setup Picture Maximize Home Security Light Multi-Media

About the TouchCenter (cont'd)
8
System Troubles
The “Security” screen also displays an Icon(s) if a system trouble(s) occurs. If a trouble Icon is shown, contact your
alarm company. The following Icons may be shown as applicable to your system:
Note: If multiple faults exist, touch the More Choices icon and then the Show Zones icon to view and scroll through the complete list of faults.
ICON FUNCTION
AC Loss – The system is not receiving AC power.
Bell Failure – The system bell or siren has a problem. Note: This Icon displays when interfacing with residential panels only.
Expander Failure – The system has a failure in an expansion module.
Low Battery – The system battery, that powers the system during an AC power loss, is low.
LRR Supervision Failure – The Communication Device used to communicate with the central station has a supervision failure.
Max Attempts Exceeded – The system has exceeded the maximum attempts to communicate with the Central Station.
Pager Failure – The system cannot communicate with an assigned pager.
Telco-1 Cut – The system is not able to communicate with the central monitoring station over the primary phone line.
Telco-2 Cut – The system is not able to communicate with the central monitoring station over the secondary phone line.
Wireless Failure – The system is not able to communicate with its wireless devices.

About the TouchCenter (cont'd)
9
User Codes
Each user must be assigned a name with a corresponding 4-digit user code in order to gain access to authorized
features and functions. Users for the system are programmed in a central user setup location that provides the
specific questions for authorization level, partition assignment, and RF zone assignment.
Extended Functionality
Extended functions are advanced functions that can be accessed through a standard alpha keypad or through the
console emulation mode on your TouchCenter touch screen. Refer to your Control Panel User Guide for these
features.
LED Operation
The TouchCenter has three LEDs as follows:
6280-001-V0
FLASHING – The system contains new
message(s) for the User.
OFF – No new messages.
RESET BUTTON
Press to reset keypad
ON – System is armed.
OFF – System is not armed.
ARMED (RED) LED
READY (GREEN) LED
ON – System is disarmed and ready to arm.
OFF – System is armed or disarmed but not
ready. If disarmed, faults or troubles are present.
MESSAGE (YELLOW) LED
SD/SDHC CARD Slot
NOTE: If the Screen Blackout feature (*EN50131 Display) is enabled (see below) the keypad returns to the “Home” screen and
the “Armed” and “Ready” status LEDs turn OFF after 30 seconds. The keypad will remain in this state until a valid user code is
entered.
*The EN50131 Display compliance feature is a European Standard designed to prevent unauthorized users from knowing the
status of the Security System.
Safe Mode
The TouchCenter contains a Safe Mode of operation. In the rare event that the TouchCenter cannot successfully
communicate in its graphic mode with the control panel, the Safe Mode is a backup mode that ensures that you can
communicate with your system. Refer to the Safe Mode section.

10
Security
Introduction to Security System Operation
You can arm your system in one of three arming modes: Away, Stay, and Night. The following table lists the three
different arming modes and the results of each.
FEATURES FOR EACH ARMING MODE
Arming
Mode FUNCTION Exit
Delay Entry
Delay Perimeter Armed Interior Armed
AWAY
Press to arm when no one is staying on the premises.
When armed in AWAY, the system sounds an alarm if
a protected door or window is opened, or if any
movement is detected inside the premises.
Yes Yes Yes Yes
STAY
Press to arm when you are staying home, but might
expect someone to use the entrance door later.
When armed in STAY, the system sounds an alarm if
a protected door or window is opened, but you may
otherwise move freely throughout the premises.
Yes Yes Yes No
NIGHT
Press to arm when you are staying home and do not
expect anyone to use the entrance door. Your installer
may have configured NIGHT Mode differently; have
the installer describe the actual settings of this mode.
Yes Yes (set for Away or
Stay Mode)
No (set for Instant or
Maximum Mode)
Yes Yes
(set for Away or
Maximum Mode)
No (set for Stay or
Instant Mode)
See note below for
Night Mode arming.
Note: Night Mode (on Residential Panels Only) arms all perimeter zones plus all zones listed in Zone List 5.
IMPORTANT: On commercial systems, “Away Auto Stay” mode is shown as “Away” mode (with all zones monitored). However, some
interior zones may not be armed.
Note: The Voice Status Icon ( ) indicates the TouchCenter Voice feature. Press the Voice Status Icon to hear system status. Wait
3 seconds and press again to hear Zone Faults or Trouble conditions. Voice status will annunciate even if Voice mode and Chime
mode are disabled. Note that the Voice feature must be enabled (by the installer) for this icon to function correctly during an alarm
condition.
Note: There is a communicator delay of 30 seconds. This delay will prevent a report to the central station if the control panel is
disarmed within 30 seconds after an intrusion alarm is triggered. This delay can be removed, or it can be increased up to 45 seconds at
the option of the user by consulting with the installer. Note that fire-type alarms are normally reported without delay.

Security (cont'd)
11
How to Arm the System
Arming the system in any mode is performed in the same way, as described below.
Note: Close all perimeter windows and doors before arming.
Arm the system as follows:
IC
ON
ACTION
NOTES
1. From the “Home” screen, touch the
SECURITY icon.
2. Touch the selected arming icon.
-a text message appears stating which zones are
arming and whether or not there is an entry delay
-the screen changes to display the remaining exit
delay time, and
-the exit delay time continues to count down to
one.
Note: If Quick Arm is Not enabled in your system, you are prompted to
enter your User Code.
•When the system is armed for Stay, Night Stay and Instant mode, the
keypad beeps 3 times.
•When the system is armed for Away and Maximum mode, you will hear
steady beeps then rapid beeping during the last 10 seconds of Exit
Delay.
When exit delay time expires, the screen automatically changes to indicate
the system is "Armed".
Note: For CP-01 installations, Maximum Mode cannot be used.
How to Arm Multiple Partitions
Note: Some systems may not have multiple partitions and the “Arm Multi-Partitions” icon may not be displayed.
To arm multiple partitions, do the following:
IC
ON
ACTION
NOTES
1. From the “Home” screen, touch the
Security icon and then the Arm Multi-
Partition icon.
2. Select the appropriate arming mode.
3. Enter the user code authorized to access
other partition(s).
4. Highlight the partition from the list on
the screen, and touch OK.
5. Select ALL to arm all partitions listed.
Note
s
:
•A user may have access to some or all of the available partitions.
•If the user code is accepted, the system displays the partitions that
the user has access to.
When exit delay time expires, the screen automatically changes to indicate
the system is "Armed".
Note: If any zones are bypassed, a “Display Faults” icon ( ) is
displayed on this screen.

Security (cont'd)
12
How to Display Faults
The Display Faults function is used when you see a “Not Ready Fault” message and want to determine where the
fault is and what type of fault it is. To display faults do the following:
ICON
ACTION
NOTES
1. From the "Security" screen, touch the
Display Faults icon.
A listing of faulted and/or bypassed zones is displayed.
As applicable, take corrective action such as closing a window or door to
correct the fault.
2. If the fault cannot be corrected, you may
choose to bypass a zone by touching the zone
to highlight it and then touching the Bypass
Selected icon.
Show Zones Icons Distressed Zone Icons
Clear
Bypasses
Refresh
Data
Bypass
Selected
Bypass All
Distressed
Zones
Alarm
Troubles
Faults
Bypass
Zones
Low
Battery
ALL
How to Bypass Zones
The Bypass function is used when you want to arm your system with one or more zones left open. Bypassed zones
are unprotected and do not cause an alarm when violated while your system is armed.
•Residential systems do not allow you to bypass fire, carbon monoxide or emergency zones. On commercial fire systems, a
specified user may be allowed to bypass fire, carbon monoxide and system zones if the user was enabled by your system
installer.
•Limits apply as to how many zones can be bypassed at one time. These limits are ten zones on residential systems and
five zones on commercial systems.
To bypass zones do the following:
ICON
A
CTION
NOTES
1. Touch the SECURITY icon.
2. Touch the MORE CHOICES icon.
Note: If any zones are bypassed or faulted, a Display Faults icon is also
displayed on this screen.

Security (cont'd)
13
ICON
A
CTION
NOTES
3. Touch the SHOW ZONES icon.
While the TouchCenter is requesting and receiving the zone data from the
control panel, the screen displays "Please Wait!". Then the zones, along with
their current status, are displayed.
4. Highlight the zone(s) to be bypassed
and touch the BYPASS SELECTED icon.
5. Enter your 4-digit user code.
Note: If zones have already been bypassed, the top of this screen indicates
“Ready Bypass”.
The screen is displayed with the instructions "To Bypass Zones, Enter Code".
6. Touch the BACK icon to return
to the “Arming” screen. The "More Choices" screen is displayed showing the system status as Ready-
Bypass.
How to Clear Bypassed Zones
A bypassed zone is automatically unbypassed when you disarm the system. If a zone is bypassed, you can remove
the bypass as follows:
ICO
N
ACTION
NOTES
1. Touch the SHOW ZONES icon.
2. Touch the CLEAR BYPASSES icon.
While the TouchCenter is requesting and receiving the zone data from the
control panel, the screen displays "Please Wait!". Then the zones, along with
their current status, are displayed.
3. Enter your 4-digit user code. The
"More Choices" screen is displayed
showing the system as “Ready to Arm”.
Note: If the system is armed and you unbypass a zone, it disarms the system .
If zones are still faulted (not ready) the system will indicate the status as “Not
Ready Fault”.
How to Disarm the System
IMPORTANT: If you return to your home or business and the main burglary sounder is on, DO NOT enter the premises, but call
the police from a nearby safe location. If you return to your home or business after an alarm has occurred and the main sounder
has shut itself off, the TouchCenter beeps rapidly upon entering, indicating that an alarm has occurred during your absence.
LEAVE IMMEDIATELY and CONTACT THE POLICE from a nearby safe location.
The system may be disarmed using either of two methods. One method is employed when you enter the premises
and the other is when you have been in the premises with the system armed (i.e., Stay and Night arming modes).

Security (cont'd)
14
To disarm the system when entering the premises:
The TouchCenter automatically displays the Entry Delay Active screen when you enter the premises:
IC
O
N
ACTION
NOTES
1. Enter your 4-digit user code.
The partition is disarmed and the "Arming" screen
is displayed showing the system as Ready to Arm.
No
te:
If you have a commercial system and a time window has been defined
for when you may disarm the system, the system does not disarm if you are
outside that time window.
To disarm the system when already in the premises:
ICO
N
ACTION
NOTES
1. Press the Disarm icon.
2. Enter your 4-digit user code.
To disarm Multi-Partitions do the following:
ICON
ACTION
NOTES
1. From the “Home” screen, press the Security icon.
2. Press the Arm Multi-Partition icon.
3. Press the Disarm icon.
4. Enter your 4-digit user code.
5. Highlight the partition(s) to disarm and press
OK, or press ALL to disarm all partitions.
The keypad displays “Multi-Partition Arming”.
How to Check the Status of Other Partitions
This system supports between one and eight Partitions (depending on the system). Partitioning enables a single
physical alarm system to control up to eight areas of protection (partitions) depending on the system you have
purchased. Each TouchCenter keypad is assigned a default partition for display purposes, and shows only that
partition's information.
Note: A letter “H” following the partition name or number indicates that this is the default partition for the TouchCenter.
For example, if your physical site is a four-apartment housing unit, your alarm system may be configured with four
partitions. Each apartment’s zones (door, windows, smoke detectors, etc.) are assigned to separate partitions, giving
each apartment independent arming/disarming control of its own partition (area). A landlord or manager may be
granted access to all partitions, so he/she can control the entire system.

Security (cont'd)
15
If a user is so authorized, a TouchCenter or other keypad in one partition can be used to perform system functions in
another partition. (Note that only those partitions authorized and programmed by the installer can be accessed in
this manner.) To check the status of other partitions perform the following:
IC
ON
ACTION
NOTES
1. Touch the SECURITY icon.
2. Touch the "Current Partition" icon (lower
edge of the screen; in this case it displays
P1H,unless changed by installer).
This screen displays the available partitions and their current status.
The current partition is shown at the top of the display (P1). To change
this assignment, select the appropriate icon (e.g., touch P2 to switch
control to Partition 2).
3. Enter the code authorized to access other
partition(s).
If the code is accepted, the system displays the
partitions that user has access to.
Note:
After leaving this screen when using a residential panel, the
selected partition in the TouchCenter automatically reverts back to the
TouchCenter’s home partition after two minutes. When using commercial
panels, you must select the TouchCenter’s home partition to return to it.
Fire and Carbon Monoxide Alarm Operation
Your fire alarm system and carbon monoxide detector (if installed) is on 24 hours a day, providing continuous
protection. In the event of an emergency, the installed smoke, heat, carbon monoxide detectors automatically send
signals to your Control/Communicator, triggering a loud interrupted sound from the keypad. An interrupted sound is
also produced by optional exterior sounders. EVACUATE ALL OCCUPANTS FROM THE PREMISES
IMMEDIATELY. Notify your Central Station/Security Company immediately and wait for further instructions.
UL
CO annunciation has not been investigated by UL and may not be used for UL installations.
In Case of Fire Alarm
1. A FIRE message appears at your keypad and remains on until you silence the alarm.
2. Should you become aware of a fire emergency before your detectors sense the problem, go to your nearest keypad
and manually initiate an alarm by touching the panic key assigned as FIRE emergency (if programmed by the
installer) and hold down for at least 2 seconds.
3. Evacuate all occupants from the premises.
4. If flames and/or smoke are present, leave the premises and notify your local Fire Department immediately.
Silencing and Clearing a Fire/Carbon Monoxide Alarm
1. Silence, acknowledge, and clear the alarm by:
a. For Residential Systems: Touch “Touch here to Silence” on the display to silence the alarm.
For Commercial Systems: Enter your code. This silences and acknowledges the alarm and the disarming
of the system (if armed).

Security (cont'd)
16
b. For Residential Systems: Touch the CLEAR icon followed by your code. This acknowledges the alarm and
the disarming of the system (if armed).
For Commercial Systems: Touch the CLEAR icon followed by your code. The system attempts to clear the
alarm from memory. If NOT successful (i.e., smoke in the detector) the Security screen is displayed and the
Display Faults icon displays a “Not Ready Fault”.
c. Touch the DISPLAY FAULTS icon on the Arming screen. The faulted fire/carbon monoxide zone is displayed.
d. Touch the CLEAR icon and then enter your code. This clears the Fire Alarm/CO Alarm from the system.
2. If the keypad does not indicate a READY condition after the second sequence, touch the DISPLAY FAULTS
icon on the Arming screen to display the zone(s) that are faulted. Be sure to check that smoke detectors/carbon
monoxide detectors are not responding to smoke, heat, or gas producing objects in their vicinity. In this case,
eliminate the source of heat, smoke or leak.
3. If this does not remedy the problem, there may still be smoke/gas in the detector. Clear it by fanning the
detector for about 30 seconds.
4. When the problem has been corrected, clear the display by touching the DISPLAY FAULTS icon on the Arming
screen, selecting the fire or carbon monoxide zone, touching the CLEAR icon and then entering your user code.
Note: Contact your Central Station/Security Company for servicing if you have further problems with your system.
More Choices
How to Clear/Hide a Control Panel Message
The Control Panel Message icon alerts the user to a control panel message. When a Control Panel Message is
displayed, the user has two options. User can clear the Control Panel Message immediately, or minimize the window
and clear it at a later time. To Clear/Hide the Control Panel Message, do the following:
ICO
N
ACTION
NOTES
1. To clear; touch CLEAR.
2. Enter your Authorized Code or,
3. To hide; touch the HIDE icon to clear the
Control Panel Message later.
Once your Authorized Code is accepted, the Control Panel Message is
cleared.
If the alarm is still present, touch CLEAR again and then enter your
Authorized Code again. Or, touch HIDE to address the condition later.
Advanced System Features
While most of the commonly used security functions are available from the TouchCenter’s advanced user interface,
there are some less used, advanced features that can either be accessed through Console Emulation mode on the
TouchCenter or a standard alpha keypad. To use features not supported by the TouchCenter, refer to your Control
Panel User Guide.

Security (cont'd)
17
Console Emulation Mode
Console Emulation Mode allows you to use a TouchCenter interface just as you would a regular system keypad. All
commands shown in Console Emulation mode can also be executed from a standard alpha keypad.
•It is recommended that you do not use the Console Emulation Mode to enter GOTO commands. Unsatisfactory
operation may result from issuing GOTO commands in Console Emulation.
•Two
button panics (1 & *, 3 & #, and * & #) do not function in the Console Emulation Mode. The A, B, C, and D
buttons do function if programmed as panic keys. Check with your system installer for details.
•Commercial systems with Alpha keypads have a feature where if you press a key for 5 seconds, you receive self
help messages about the pressed key or holding the * key for 5 seconds to provide zone descriptors. These features
do not function in the TouchCenter as all key presses are instantaneous.
How to Enter Console Emulation Mode
To access the TouchCenter "Keypad," do the following:
IC
ON
ACTION
NOTES
1. Touch the SECURITY icon.
2. Touch the MORE CHOICES icon.
3. Touch the CONSOLE MODE icon.
Perform functions as you would from a standard alpha keypad .
How to View the Event Log
Your system has the ability to record various events in a history log wherein each event is recorded with the time
and date of its occurrence. The control panel must be programmed to record various system events in the installer
programming mode. To view the Event Log, perform the following:
IC
ON
ACTION
NOTES
1. From the “Home” screen touch Security and
then the MORE CHOICES icon.
2. Touch the EVENT LOGS icon.
Note: While TouchCenter is requesting and receiving the event log data
from the control panel, the "Event Log" screen displays "Please Wait!".
The Next>> and <<Previous icons are shown for commercial panels only
when 100 or more events are in the log. They are not shown for
residential panels.
When All Partitions or All Events icon is pressed, and more than 100
events exist, the Next>> and <<Previous icons are displayed showing the
next 100 or previous 100 events.
The first ten events are displayed.
3. Touch the SHOW MORE button to view all
items, and touch the up/down arrows to scroll
through the event log.

Security (cont'd)
18
How to Send Emergency Messages
• Emergency messages are optional and may not be available on your system. Ask your system installer if emergency messages
are available on your system.
•The Emergency screen cannot be accessed while running a screen diagnostic test or while in the clean screen mode.
An emergency message for fire, panic, or medical can be sent to the central monitoring station from the Emergency
screen. The Emergency screen can be accessed by activating the "PANIC" Icon.
Perform the following to send an emergency message.
ICON ACTION NOTES
1. Touch the PANIC icon.
2.Touch and hold (for at least 2 seconds) the
associated alarm icon (FIRE, PANIC, SILENT
PANIC or MEDICAL).
You are immediately returned to the screen from which you pressed the
“PANIC” Icon.
Emergency Icons
Fire
Panic
Silent Panic
Medical
UL
Medical functionality has not been evaluated by UL and may
not be used in UL Listed applications.

19
Setup
Setup allows you to make changes to the way your TouchCenter is operating. You may access the Brightness and
Volume, Display & Audio Setup, System Setup (if enabled by your system installer), and System Information
from the "Setup" screen.
Brightness and Volume Control
From the "Home" screen, access the "Setup" screen as follows:
IC
ON
ACTION
NOTES
1. From the “Home” screen, touch the Setup
icon.
2. Move the Brightness/Volume slide bar up or
down to increase or decrease brightness/volume.
If you have made any changes in these settings, when you exit a Settings
Changed! pop-up window is displayed asking “Remember New Settings?“
Yes saves the change.
No discards the change
.
Display & Audio Setup
You may access Operating Modes, Languages, Backlight Off After time, To Homepage After time, Auto
Slideshow After time and Clean Screen from “Display & Audio Setup” screen.
Operating Modes
Operating modes provides access to Chime Mode, Voice Mode, and Voice Chime which allows you to turn the
TouchCenter chime mode and voice mode on or off.
•Chime Mode – TouchCenter chimes whenever a door or window is open.
•Voice Mode – TouchCenter voice annunciates whenever a change in system status occurs such as Armed,
Disarmed, or Alarms.
•Voice Chime – The chime mode and voice mode are in effect with the chime beeps followed by voice annunciation.
Access the "Operating Modes" screen as follows:
ICON
ACTION
NOTES
1. From the “Setup” screen, touch the Disp &
Audio Setup icon.
2. Enter your “Authorized Code", if required.
If the Chime Mode and Voice Mode are both selected, then Voice Chime is
automatically selected.
3. Select Chime Mode or Voice Mode to turn
the mode on or off.
4. Touch the HOME or BACK icon after making
your selection.
It may take a few seconds for the Chime Mode to take effect.
When the TouchCenter exits the “Operating Modes” screen, your selection is
saved.

Setup (cont'd)
20
Language Selection
To change the Keypads display language, do the following:
ICON
ACTION
NOTES
1. From the “Home” screen, touch the Setup icon.
2. Enter your “Authorized Code”.
3. Highlight the button next the desired language.
4. Touch the Back arrow.
The TouchCenter allows you to select from three languages, (English,
French Canadian and Latin American Spanish) with the default being
English
.
Once the language is selected, the keypad will revert back to "Home"
screen with the selected language applied.
Adjust the Screen Timeouts
When the TouchCenter is left idle, it automatically:
•turns the “Backlight Off After” the selected backlight off time has expired (unless “Never” option is selected).
•returns to the “Home” screen after the selected “To Homepage After” time has expired (unless “Never” option
is selected), and
•if enabled, the “Auto Slideshow After” time begins the slide show.
To select the desired screen timeouts, do the following:
IC
ON
ACTION
NOTES
1. From the "Home" screen, touch the Setup icon.
2. Touch the Disp & Audio Setup icon.
3. Enter your “Authorized Code".
4. Touch the desired selection from the drop-down
list displaying the time period for each option.
If you have made any changes in these settings, when you exit a
Settings Changed! pop-up window is displayed asking “Remember
New Settings?“
Settings include:
•Backlight Off After X time
•Return To Homepage After X time
•Auto Slideshow After X time.
Note: The “To Homepage After” option is only available if the EN50131
display option is not enabled by the installer.
Yes saves the change.
No discards the change.