Honeywell ImperLED User manual

GB
ImperLED
Surface Mounted
Dimensional Drawings:
Installation:
Step 1: Place a flat blade screwdriver and pull up gently the diffusor’s clips from both sides to remove the diffusor.
Step 5: Connect the 24V cable to the respective terminal block: C1 and C2. Power supply cables cross section
2
should be 0.8 – 3 mm . Open a second hole on the plastic base, install the rubber gasket and pass another
one 24V cable . Connect the second 24V cable to the respective terminal block: C1 and C2 and connect it
to the next luminaire.
Step 2: Place a flat blade screwdriver and pull up gently the reflector.
Step 3: Install the plastic base with the included mounting screws and plugs. If the hole that exists is not useful,
drill another hole on one of the designated positions in order to pass the cables and install the included
gasket (verify that are not deformed).
Step 4: Install the included rubber gasket (verify that is not deformed). Make a hole in the center of the rubber
gasket by using a small screwdriver. Pass the round cable through the rubber gasket. Install the included
tie-wrap to the included adhesive tether loop and fasten securely the power cable in order to anchor it.
Install the power cable as shown in the picture. Always use in any case round mains cable, with a diameter
2
of 5-10mm (H05RN-F type 2x1mm ) or any other type, at least equal to it's mechanical and electrical
properties). ATTENTION!! The cable must not be deformed in any way (This requirement is important to
ensure the IP rating).
Step 6: Refit carefully the removed plastic parts. Finally place the diffusor. Attention!! The plastic lathces (A)
must be secured (click sound). This requirement is important to ensure the IP65 rating. Power on the
luminaire.
To other luminaire
Adhesive tether
loop
5
1
4
24V IN
24V IN
24V OUT
24V IN
24V IN
24V OUT
17-27V AC/DC
To other luminaires
23
Honeywell Life Safety AS, Postboks 236, 1372 Asker http://www.hls-nordic.com
AA
A
A
A
click
A
click
6

Pictogram Installation
Mounting Methods
Mounting Accessories (Available After Request)
Step 1: Place a flat blade screwdriver and pull up gently the diffusor's clips from both sides to remove the
diffusor.
Step 2: Install the pictogram you need in the diffusor and refit it to the luminary. (In case you need to
change the pictogram follow the same procedure.)
Step 3: Fill in, the letter G on the specification label.
ImperLED luminaries can be surface mounted on walls or ceilings.
1 AA E
X6 0
G
Wall
bottom
view
Wall installation
290405.11 ImperLED Suspended Pictogram 290471 ImperLED Wall Bracket
Ceiling installation
Ceiling
Honeywell Life Safety AS, Postboks 236, 1372 Asker http://www.hls-nordic.com
GB

Technical description
Part no.:
o
-30 to 50 C
Up to 95%
Produced in accordance with:
Ambient Temperature Range:
Maximum Power Consumption:
Operation Voltage:
Relative Humidity:
Technical lifetime (light source):
Lumen output
> 100000 hours
350lm
ImperLED CBS 24V
2.3W / 2.6VA
17-27V AC/DC,50-60Hz
290148
IP65
Degress of cover protection:
EN 60598-1, EN 60598-2-22, EN 55015
EN 61547, EN 61000-3-2, EN 61000-3-3
Weight: 720 gr
Honeywell Life Safety AS, Postboks 236, 1372 Asker http://www.hls-nordic.com
GB
Note: If the supply cable of the luminaire is damaged, it shall exclusively be replaced by a competent person in
order to avoid hazard.
The light source of this luminaire is not user replaceable. When the light source reaches its end of life the
whole luminaire shall be replaced.
At the end of their useful life the packaging & product should be
disposed of via a suitable recycling centre. Do not dispose of with
your normal household waste. Do not burn.