Honeywell FBII OMNI 624 Assembly instructions

N9967V3 4/04 Rev. A
FBII Security System
Security SystemSecurity System
Security System
OMNI®624
Version 2.X
Installation and Setup Guide

ii
THANK YOU for your purchase of the
OMNI624 Security System.
The purpose of this manual is to give you a brief overview of the OMNI®624 control panels, and
provides instructions for installing a basic system. Honeywell is always available to serve YOU.
Our SALES and TECHNICAL SUPPORT staff are available to assist you in any way possible.
World Wide Web Address ..........................................http://www.honeywell.com/security
FAX ............................................................................................................... 516-921-4327
Sales
Inside the United States ..................................................................... 800-645-5430
Outside the United States................................................................... 516-921-8666
Technical Support: (8 a.m.-8 p.m. E.S.T.)
Inside the United States ..................................................................... 800-645-7492
Outside the United States................................................................... 516-921-8666
Before you call Technical Support, PLEASE be sure you:
•Check the wiring diagram and verify your connections.
•Check all fuses.
•Assure that the transformer and backup battery voltages are supplying the proper voltage
levels.
•Verify your programming information.
•Read this manual thoroughly.
•Consult the Troubleshooting Section of this manual.
•Note the proper model number of this product, and the version level (if known) along with any
documentation that came with the product.
•Have your company name and telephone number ready.
This information will allow us to service you more quickly and effectively. Please, remember to
BE PATIENT while waiting on the telephone; your call will be answered as soon as possible.
FOR YOUR CONVENIENCE, a separate Programming Guide is included with this manual. It
provides space for listing entries for each programming question.
NEW FEATURES OF VERSION 2.X
• Wireless Jamming Detection Processing
• Crystal Controlled Real-Time Clock
• Silent Zone, RF Jam, and Keypad Tamper
Triggers
• Keypad Tamper to Detect Keypad Removal
• Activate Dial Delay if Armed-Stay Option
• Keypad Supervision and Zone Unbypass
Logged

iii
Table of Contents
•••••••••••••••••••••••••••••••••••••••••••
SECTION 1 – CENTRAL STATION REPORTING FORMATS....................................................... 1–1
System Features .................................................................................................................................. 1–1
Special Notes........................................................................................................................................ 1–2
SECTION 2 – SYSTEM WIRING AND HOOKUP .............................................................................. 2–1
System Wiring Diagram ...................................................................................................................... 2–1
Terminal Connections.......................................................................................................................... 2–2
Auxiliary Device Current Draw Worksheet........................................................................................ 2–5
Wiring Information for Keypads & Other Devices............................................................................. 2–6
SECTION 3 – PC BOARD AND KEYPAD MOUNTING ................................................................... 3–1
Mounting the OMNI624 PC Board ..................................................................................................... 3–1
Mounting the RF Expander Module ................................................................................................... 3–2
Mounting the Zone Expander Module ................................................................................................ 3–2
Keypad Mounting Instructions ........................................................................................................... 3–2
SECTION 4 – SYSTEM CONFIGURATION ....................................................................................... 4–1
Partitioning .......................................................................................................................................... 4–1
Hardwire Zones and Zone Expansion Module.................................................................................... 4–1
Wireless Transmitters ......................................................................................................................... 4–2
Relay/Trigger Outputs......................................................................................................................... 4–3
Paging Feature..................................................................................................................................... 4–4
SECTION 5 – SYSTEM OPERATION.................................................................................................. 5–1
Power Up/System Reset....................................................................................................................... 5–1
Keypads ................................................................................................................................................ 5–1
Keypad Sounder................................................................................................................................... 5–3
Keypad Backlight Timer...................................................................................................................... 5–4
Keypad Addressing .............................................................................................................................. 5–5
Arming the System .............................................................................................................................. 5–5
User Code Programming ..................................................................................................................... 5–8
User Deletion ..................................................................................................................................... 5–10
Keypad Emergency Conditions ......................................................................................................... 5–10
Quick Command Modes..................................................................................................................... 5–11
SECTION 6 – SYSTEM PROGRAMMING .......................................................................................... 6–1
Programming Methods ........................................................................................................................ 6–1
System Default..................................................................................................................................... 6–1
Keypad Programming.......................................................................................................................... 6–2
Installer Modes Summary ................................................................................................................... 6–5
Data Entry via Keypads ...................................................................................................................... 6–9
Summary of System Programming ................................................................................................... 6–11
Programming Submode 1: SYSTEM OPTIONS ............................................................................... 6–11
Programming Submode 2: ZONE PROGRAMMING / REPORT CODES ....................................... 6–45
Programming Submode 3: WIRELESS TRANSMITTER PROGRAMMING.................................. 6–51

iv
Programming Submode 4: DESCRIPTOR PROGRAMMING ......................................................... 6–53
SECTION 7 – SUMMARY OF KEYPAD FUNCTIONS ..................................................................... 7–1
User Functions..................................................................................................................................... 7–1
Installer Modes .................................................................................................................................... 7–2
SECTION 8 – CENTRAL STATION REPORTING FORMATS....................................................... 8–1
General Information ............................................................................................................................ 8–1
Standard (3x1 or 4x1) .......................................................................................................................... 8–1
Extended (3x1 Ext. or 4x1 Ext.) .......................................................................................................... 8–2
Partial Extended (3x1 Part. Ext. or 4x1 Part. Ext.) ........................................................................... 8–2
3x2 or 4x2 ............................................................................................................................................. 8–3
FBII Superfast (4x3x1) ........................................................................................................................ 8–3
ADEMCO 4x1 Express ........................................................................................................................ 8–4
ADEMCO 4x2 Express ........................................................................................................................ 8–4
ADEMCO Contact ID .......................................................................................................................... 8–5
SECTION 9 – TROUBLESHOOTING.................................................................................................. 9–1
SECTION 10 – REGULATORY/LIMITATIONS STATEMENTS................................................... 10–1
SECTION 11 – CE LOW VOLTAGE DIRECTIVE............................................................................ 11–1

v
Conventions Used in This Manual
•••••••••••••••••••••••••••••••••••••••••••
Before you begin using this manual, it is important that you understand the meaning of the following
symbols (icons) and text note.
ULThese notes include specific information that must be followed if you are installing this system
for a UL Listed application.
These notes include information that you should be aware of before continuing with the
installation, and which, if not observed, could result in operational difficulties.
!
This symbol indicates a critical note that could seriously affect the operation of the system, or
could cause damage to the system. Please read each warning carefully. This symbol also
alerts the user to the possibility of physical harm if instructions are not followed as written
.
Note: These text notes are provided throughout the manual to provide informative information and
shortcut tips for the installer.

vi

1–1
SECTION 1
Introduction
•••••••••••••••••••••••••••••••••••••••••••
System Features
The OMNI®624 is a state-of-the-art microprocessor-based control/communicator that provides 2
partitions and supports both hardwire and wireless zones. Programming can be performed through any
of the compatible keypads, or the system can be uploaded and downloaded remotely using the Compass
Downloader Software. Additionally, the software can be programmed to control remote actions, such as
arming, disarming, bypassing, etc. Programming options are stored in an Electrically Erasable
Programmable Read Only Memory (EEPROM). The EEPROM is nonvolatile, meaning that
programmed instructions will not be lost in the event of a loss of power.
Features of the OMNI624 include:
•2 independent partitions
•Up to 24 zones that may be comprised of a
combination of hardwire and wireless or
wireless zones
•6 hardwire zones (all fully programmable,
including keyswitch), expandable to 8
additional hardwire zones using optional plug-
in OMNIEXP8 Expansion module
•Hardwire zones can be configured as standard
or double-balanced, or can be set for zone
doubling (providing up to 24 hardwire zones if
zone expander is used)
•Up to 24 wireless protection zones plus up to 8
wireless keys
•Cross-zoning capability
•32 User Codes (either 4-digit or 6-digit codes
can be used)
•Up to 12 keypads (OMNI-LCD, OMNI-LCD-US,
XK7LC, OMNI-KP, OMNI-KP-US)
•OMNI-LCD, OMNI-KP, and XK7LC keypads
are not for sale in the USA.
•XK108 keypads may also be used;
however, the system can only have XK108
type keypads attached and the system must
be set up as having one partition.
•Keypad programming and remote programming
via PC and modem
•3 emergency keypad conditions (Panic, Fire, &
Auxiliary)
•128 Event History Log (alarms, troubles, low
battery, bypasses, central station (CS) test,
openings & closings) and keypad events
•20 programmable relay outputs (using optional
XL4705 modules)
•4 built-in programmable trigger outputs (2
triggers if relay module is used)
•Real-time clock (displays time & date via LCD
keypad) with reminder when clock needs to be
set
•CS test timer by event, time or both (1 hour, 1,
7, 27, 60, 90 Days)
•Customer control of Chime mode and Pager
mode
•Quick Arming, Quick Bypass, and Quick Force
Arming
•CS reporting by zone
•False alarm prevention features: Crossed
Zones, Exit Error, Recent Close, Swinger
Shutdown
•Cancel Code & System Stabilization during
power-up
•Arming by keyswitch in Away or Stay mode
•Keypad Tamper/Lockout with optional CS
reporting
•Restore transmission options: After Loop or
After Bell

OMNI624 Installation and Setup Guide
1–2
•Upload/download and remote commands
•3 methods of uploading/downloading: PC,
operator-initiated, and unattended
•Paging (audio format) capabilities
•Auto-arming at a specific time of day with
capability to arm in either Away, Stay, or
Instant modes
•Dual entry timers
•Fire zone reset through keypad
•Glassbreak reset through keypad
•Bell Test, Low Battery Test, AC loss and
communications failure
•Input power: 16.5VAC, 25VA; 12VDC, 4-7AH
•Output power: 12VDC, 500mA
•Bell output power: 12VDC, 1A
Special Notes
!
IMPORTANT - Failure to install and program this unit in accordance with the UL
requirement is a violation of the listing mark. For more information on UL Listings,
contact Underwriters Laboratories, Progress Department, 333 Pfingsten Road,
Northbrook, IL 60062.
UL Listings
The OMNI624 is the Residential (Household) version of the control panel, and has been Listed by
Underwriters Laboratories for the following applications:
•UL 1023 Household Burglary
•UL 985 Household Fire Warning
FCC Registration Number: 5GBUSA-44003-AL-E
References to Programming Questions
Programming questions are grouped into 4 installer programming submodes, as follows:
1 – System Options
2 – Zone and Report Code Programming
3 – Wireless Zone/Keyfob Programming
4 – Zone Descriptor Programming
Throughout this manual, programming question references without a submode designation pertain to
questions in submode 1 (system options). Programming questions for other submodes include the
appropriate submode number.

2–1
SECTION 2
System Wiring and Hookup
•••••••••••••••••••••••••••••••••••••••••••
System Wiring Diagram

OMNI624 Installation and Setup Guide
2–2
SYSTEM STABILIZATION MODE: When powering up a system that was previously armed when
power was removed, the system will enter a 2-minute stabilization period. This 2-minute interval is
used to allow motion detectors to stabilize. “PLEASE STAND BY” and “POWER UP DELAY” are
displayed on the OMNI-LCD, OMNI-LCD-US and XK7LC keypads. “PL” is displayed on the OMNI-
KP and OMNI-KP-US keypads, and the Armed LEDs on both types of keypads are lit. All LEDs on
the XK108 keypad are lit.
Terminal Connections
1 & 2 — TRANSFORMER: Connect the 16.5VAC 25VA transformer, utilizing 18AWG (1mm dia.) or
larger wire at a distance not to exceed 15 feet (4.5m) from the panel, to an unswitched source of
AC mains power (120 or 220VAC).
The system can supply up to 1.8 amps of total current.
For US installations, use an ADEMCO No. 1321 transformer or for Canadian installations, use an
ADEMCO No. 1321CN transformer. For all other installations, use a transformer that complies
with the above specifications. Do not use any other rating transformer, as this may result in
improper operation or damage to the unit.
The “AC/LOW BAT” keypad LED remains ON while AC power is present. If an AC loss occurs, the
“AC/LOW BAT” LED turns off immediately. If AC power remains OFF for 15 minutes, the system
pulses the keypad buzzer and transmits a power-loss message to the central station, if programmed
to do so. THE KEYPAD BUZZER CAN BE SILENCED by entry of any valid user code. When AC
restores, the “AC/LOW BAT” LED lights immediately, and a Restore code is reported, if
programmed.
3(+) & 4(–) — BELL OUTPUT: The total output power available for sounding devices is 1 amp (650 mA
for UL installations) at 11.5 - 13.1VDC. These terminals will deliver CONSTANT output on
BURGLARY, AUDIBLE PANIC, and BELL TEST. On a FIRE condition, a PULSED or TEMPORAL
output can be generated. There are separate bell cutoff times programmable for burglary and fire
conditions within the programming sequence. For UL Household Fire Warning System
installations, the speaker must be mounted indoors for best audibility. Also, for UL installations,
use only one speaker.
NOTE: Before connecting sounding devices, please consult their specifications for proper current
draw. Otherwise, the bell fuse (F1) may be blown.
NFPA 72 REQUIREMENT: All the
interconnecting pathways (cable,
wire, etc.) between the alarm
system initiating device (control
panel) and the signaling device
(bell, speaker, siren, etc.) shall be
monitored for an occurrence of an
open circuit, which prevents the
normal operation of the system. An
occurrence of an open circuit shall
be indicated by a distinctive trouble
signal.
BELL SUPERVISION (Bell) - To meet the NFPA 72
requirement, program Question 12, Location 3, in
Programming Submode 1 for bell supervision. The bell is then
supervised for an open circuit (not a short circuit) across the
bell output terminals; the keypad will indicate that a bell
supervision condition has occurred and fire trouble is reported
to the CS if enabled. If the bell is already ringing, the
supervision will not take effect until after bell cutoff time. Refer
to the following diagrams: