Honeywell LYNX Touch 5100 Operating instructions

LYNX Touch
Security System
Programming Guide
800-11060 2/12 Rev. A

Table of Contents
Entering Programming Mode....................................................................................................................................3
Programming the Data Fields...................................................................................................................................3
Loading a Default Set...............................................................................................................................................3
Exiting Programming Mode......................................................................................................................................3
Data Fields................................................................................................................................................................4
Change Installer Code...........................................................................................................................................4
Program System Type...........................................................................................................................................4
Program Date and Time........................................................................................................................................5
Program Communications.....................................................................................................................................5
Program Zones......................................................................................................................................................7
Program Keys........................................................................................................................................................8
Program Reporter..................................................................................................................................................9
Program Sounder................................................................................................................................................13
Program System Settings....................................................................................................................................14
Program the Z-Wave Module..............................................................................................................................16
Zone Programming Worksheet..............................................................................................................................17
Explanation of Zone Assignment Table Headings ..............................................................................................18
5800 Series Transmitter Loop Numbers Diagram..................................................................................................19
Programming Default Tables..................................................................................................................................20
LYNX Touch Summary of Connections Diagram...................................................................................................23
Refer to the LYNX Touch Series Installation and Setup Guide P/N 800-10614 or later for detailed information on
programming the system. The Installation and Setup Guide contains full descriptions for all data fields.
UL LYNX Touch is not intended for UL985 Household Fire applications unless a 24-hour backup
battery (P/N LYNXRCHKIT-SHA) is installed.

- 3 -
Entering Programming Mode
You may find it convenient to adjust the volume setting before entering the Programming Mode. This
will allow you to clearly hear feedback announcements or system beeps.
1. Power up the LYNX Touch control, when the Home Screen appears, select “More”.
2. Select “Tools”. The system displays a virtual keypad.
3. Enter: Installer Code (4 + 1 + 1 + 2).
4. The System Programming Screen is displayed. Select “Program”. The Armed and Ready LEDs will flash and
the following options will be displayed:
Installer Code
Date Time
Zones
Keys
System Type
Communicator
Comm. Diagnostics
Reporter
Use the down Tarrow to scroll to the next page of options.
Sounder
Default Config.
Reset Master Code
System Settings
Language*
Z-Wave
* This field may not be applicable to the system being installed.
5. Select an option to advance to that Programming screen.
Note: If a different Installer Code has been programmed, enter: the New Installer Code.
Programming the Data Fields
1. Select each desired programming option, and then select the required entry. The system beeps each time a
selection is made.
2. The system will toggle or scroll through the options or display a new screen as required for the specific
option.
3. To delete or change an entry, simply select the desired option, and then select the required entry.
Loading a Default Set:
1. Enter the Installer Programming Mode and advance to second page of the System Programming.
2. Select ‘Default Config’ and select the appropriate Default Table Configuration from the following options or
Select Default Downloader to reset all subscriber account numbers and CSID in preparation for an initial
download:
Default Config 1
Default Config 2
Default Config 3
Default Config 4
Default Downloader
Note: Refer to the Programming Default Tables section of this manual to view the default values.
Exiting Programming Mode:
1. Select the “2” key to exit the current screen. The system returns to the previous screen.
2. Select the “2” key as required until system displays a Confirmation screen.
3. Select “Yes” to allow the installer to re-enter Programming mode or “No” to prevent re-entry. If “No” is
selected, you can still re-enter Program Mode by powering down the unit (remove AC and battery power) and
entering Program Mode within 30 seconds of powering up.
4. Select the “2” key again to return to the Home Screen.

Screen Display Function & Programming Options
- 4 -
DATA FIELDS
Note: If applicable, preprogrammed defaults for the LYNX Touch Control are shown on the screen display.
Change Installer Code
5000-100-129-V0
Installer Code
Installer Code
Enter 4 digits [The defaulted Installer Code is 4112]
0-9
Program System Type
RF Jam
Disabled
RF Jam
Disabled
Enabled
Speaker Phone
Enabled
Speaker Phone
Disabled
Enabled
Two Way Voice
Disabled
Two-Way Voice
Disabled
Enabled
RF House Code
0
RF House Code
Enter 2 digits, 00-31
Phone Notification
Disabled
Phone Notification
Disabled
Keypad
Trouble
Note: If “Keypad” or “Trouble” is selected you will be prompted to program a phone detect time.
Phone Detect Time
2 Minutes
Phone Detect Time
1 Minute
2 Minutes
3 Minutes
4 Minutes
Remote Phone
Enabled
Remote Phone
Disabled
Enabled
Events - Log All
Press To Log All
Events – Log All
Note: If Press to Log All is selected the system will log the following events:
Alarm
Bypass
Open/Close
Trouble
Non-Security
Events – Log Alarm
Enabled
Events – Log Alarm
Enabled
Disabled
Events – Log Bypass
Disabled
Events – Log Bypass
Enabled
Disabled
Events – Log Open
Close
Disabled
Events - Log Open/Close
Enabled
Disabled
Events – Log Trouble
Enabled
Events – Log Trouble
Enabled
Disabled
Non Security
Disabled
Non Security
Enabled
Disabled
Remote Access Serial
Disabled
Remote Access Serial
Enabled
Disabled
Note: If the “Remote Access Serial” option is enabled, you will be prompted to select a “Multi Mode Serial”.

Screen Display Function & Programming Options
- 5 -
Multi Mode Serial
Disabled
Multi Mode Serial
Enhanced Reports
Disabled
Program Date and Time
5000-100-131-V0
Date Time
Date Time
Note: If you are installing a GSMVLP5 or ILP5 Communication Module, the time and date will be
programmed and updated automatically via Central Station. You must still program the correct
Time Zone below.
1. Month and Year
2. Select the correct date
3. Enter the correct time
4. Select AM or PM
5. Select Save or continue below.
Time Zone
Eastern (EST)
Time Zone
Eastern (EST) Mountain (MST) Atlantic (AST)
Central (CST) Pacific (PST) Newfoundland (NT)
Hawaii (HAST) Alaska (AKST)
Day Light Savings Time
Yes
Day Light Savings Time
Yes
No
Note: If Yes is selected, the following options will be active.
Start Month
March
Start Month
January July
February August
March September
April October
May November
June December
Start Week
Second
Start Week
First
Second
Third
Fourth
Last
Next to Last
3rd from Last
End Month
November
End Month
January July
February August
March September
April October
May November
June December
End Week
First
Start Week
First
Second
Third
Fourth
Last
Next to Last
3rd from Last
Program Communications
5000-100-132-V0
Communicator
Communicator
Program the following options:
Communications Path APL
City ID CS ID Sub ID
Supervision Old Alarm Time
Remote Acc. Comm. Multi Mode Comm.
GSM Fault Time OR
IP Fault Time

Screen Display Function & Programming Options
- 6 -
Communications Path
None
Communications Path
None
IP
GSM
WiFi
WiFi & GSM
APL
Disabled
Advanced Protection Logic
Enabled
Disabled
City ID
Primary City Identification
Enter 2 digits
01-99
CS ID
Primary Central Station Identification
Enter 2-digits (HEX)
01-FE
Sub ID
Primary Subscriber Identification
Enter 4-digits
0001-9999
Supervision
24 Hours
Supervision
24 Hours
None
30 Days
Old Alarm Time
10 Minutes
Old Alarm Time
10 Minutes 15 Minutes
30 Minutes 1 Hour
2 Hours 4 Hours
8 Hours 12 Hours
24 Hours
Remote Acc. Comm.
Disabled
Remote Access Communication
Disabled
Enabled
Note: If enabled the following option will be active.
Multi Mode Comm.
Disabled
Multi Mode Communication
Disabled
Relay Reports
Enhanced Reports
GSM Fault Time (min)
00
GSM Fault Time (min) (displayed if GSM is selected as Communications Path)
Enter 2-digits
00-99
IP Fault Time (min)
00
IP Fault Time (min) (displayed if IP is selected as Communications Path)
Enter 2-digits
00-99
Use DHCP
Yes
Use DHCP Note: If disabled the following options will be active.
Yes
No
NIC IP Address
255.255.255.255
IP Fault Time
Enter 4 part address
Subnet Mask
255.255.255.255
Subnet Mask
Enter 4 part address
Gateway IP Address
255.255.255.255
Gateway IP Address
Enter 4 part address
DNS Server IP Address
255.255.255.255
DNS Server Address
Enter 4 part address

Screen Display Function & Programming Options
- 7 -
Program Zones
5000-100-133-V0
Zones
Zones
Select from the following zone options:
1. New
3. Back Door
5. Motion Sensor
7. – 48. New
49. – 56. 4 Button
57. – 64. New
80. – 85. Temperature
95. Fire
96. Medical
99. Police
2. Front Door
4.Window
6.New
Select a zone and then select “Edit” or “Add New” to program the next available zone.
Program the following options:(dependent upon Zone Type):
Serial Number Loop Number
Zone Description 1 Zone Description 2
Device Type Response Type
Report Chime Supervision
Serial Number
Serial Number
When “Serial Number” has been selected “Enter Serial Number or Activate” is displayed.
The transmitter serial number and loop number can be enrolled via RF transmission OR
manually.
Enroll via RF Learning To enroll the device using RF Learning mode three transmissions
(open/close) of the device will be required. The initial transmission activates the RF
Learning mode and the system will emit a single beep. A second transmission enrolls the
serial number and the system beeps two times and displays “Activate Sensor Again To
Confirm”. A third transmission will confirm the serial number. The system beeps two times
and returns to the Zone programming Screen.
Enroll Manually
Enter the 7-digit serial number printed on the transmitter using the displayed keypad and
select “Done”. The system beeps one time and returns to the Zone programming Screen.
Loop Number
1
Loop Number
1, 2, 3 or 4
Zone Description 1
Zone Description 2
Zone Description 1
The system announces the Zone Description. If desired, enter a zone descriptor.
Zone Description 2
The system announces the Zone Description. If desired, enter a zone descriptor.
Device Type
Device Type
Choose from the following options (dependant upon the Device Type):
New Door
Window Motion Sensor
Glass Break Smoke Detector
Heat Sensor Carbon Mono. Det.
Temperature Flood
Environmental Medical
Fire Police
Other
Response Type
Not Used
Response Type
Choose from the following options (dependant upon the Zone):
Not Used Arm Stay Fire No Verification
Entry Exit 1 Disarm Monitor
Entry Exit 2 Silent Burglary Trouble
Interior Follower Resident Response Arm Away
24 Hour Silent General Response No Response
24 Hour Auxiliary Perimeter Resident Monitor
Interior With Delay Day/Night General Monitor
Carbon Monoxide 24 Hour Audible Fire With Verification
Report
Yes
Report
Yes
No

Screen Display Function & Programming Options
- 8 -
Chime
No
Chime
Yes
No
Supervision
Supervised
Supervision
Hardwire Zone
Normal Open
Normal Closed
End of Line
RF Zone
Supervised
Unsupervised
Temperature
High Temp
Low Temp
Program Keys
Keys
Keys
Select from the following options:
Edit Add New Delete
If add new is selected the following options can be programmed:
Key Type User
Serial Number Zone
Button Key 1 – Zn 49 Button Key 2 – Zn 50
Button Key 3 – Zn 51 Button Key 4 – Zn 52
Button Key 5 – Zn 53 Button Key 6 – Zn 54
Button Key 7 – Zn 55 Button Key 8 – Zn 56
Key Type
4 Button Key
Key Type
1 Button Key.
2 Button Key
4 Button Key
6 Button Key
8 Button Key
User
User
Master
Duress
Babysitter
User 3 through User 14
Note: The Key must be associated with a specific User/User Code in order for it to operate. Refer to the
LYNX Touch User Guide for additional Information regarding User Codes.
Serial Number
0
Serial Number
When “Serial Number” has been selected “Enter Serial Number or Activate” is displayed.
The transmitter serial number and loop number can be enrolled via RF transmission OR
manually.
Enroll via RF Learning To enroll the device using RF Learning mode three transmissions
(open/close) of the device will be required. The initial transmission activates the RF
Learning mode. A second transmission enrolls the serial number and the system beeps two
times and displays “Activate Sensor Again To Confirm”. A third transmission will confirm the
serial number. The system beeps two times and returns to the Zone programming Screen.
Enroll Manually
Enter the 7-digit serial number printed on the transmitter using the displayed keypad and
select “Done”. The system beeps one time and returns to the Zone programming Screen
Zone
49
Zone
Manually enter a specific two-digit Zone Number (49-64).
Button Key * - Zone *
Button Key * Zn *
Enter a function for each button key from the following options:
Disarm Arm Away
Arm Stay No Response
24 Hour Silent 24 Hour Audible
24 Hour Auxiliary Silent Burglary
Fire No Verification
* Options are the same for each Button/Zone combination.

Screen Display Function & Programming Options
- 9 -
Program Reporter
Reporter
Reporter
Program the following options:
Primary CS Info Secondary CS Info
Follow Me Phone 1 Follow Me Phone 2
Report Selection Options
Downloader
Primary CS Info
Primary Central Station Information
Phone Type
Communicator Type
Phone Type
Contact Id: 4 Digit
Phone Type
None
Contact Id : 4 Digit
Contact Id : 10 Digit
SIA
Note: If SIA, Contact Id: 4 Digit, or Contact Id: 10 Digit is selected the Phone Number and Account
Number options will be displayed.
Communicator Type
None
Communicator Type
None
GSM
WiFi
WiFi & GSM
IP
Note: If IP is selected the Dynamic Priority option will be displayed.
Phone Number
Phone Number
Enter the Primary Central Station Phone Number (Up to 20 digits)
Account Number
FFFF
Account Number
Enter the Primary Central Station Account Number
Dynamic Priority
Dynamic Priority
Redundant Reports
Preferred Telco
Preferred Radio
Note: If Preferred Telco or Preferred Radio is selected the Dynamic Delay option will be displayed.
Dynamic Delay
Dynamic Delay
15 Seconds
30 Seconds
60 Seconds
90 Seconds
Report All
Press to Report All
Report All
Press to Report All
Report All Set
Report Alarms
Enabled
Report Alarms
Disabled
Enabled
Report Troubles
Enabled
Report Troubles
Disabled
Enabled
Report Open/Close
Disabled
Report Open/Close
Disabled
Enabled
Report Tests
Enabled
Report Tests
Disabled
Enabled
Secondary CS Info
Secondary Central Station Information
Phone Type
Communicator Type
Phone Type
None
Phone Type
None
Contact Id: 4 Digit
Contact Id: 10 Digit
SIA
Note: If SIA, Contact Id: 4 Digit or Contact Id: 10 Digit is selected, the Phone Number and Account
Number options will be displayed.

Screen Display Function & Programming Options
- 10 -
Communicator Type
None
Communicator Type
None
GSM
WiFi
WiFi & GSM
IP
Note: If IP is selected the Dynamic Priority option will be displayed.
Phone Number
Phone Number
Enter the Secondary Central Station Phone Number (Up to 20 digits)
Communicator Type
None
Communicator Type
None
GSM
IP
Note: If IP is selected the Dynamic Priority option will be displayed.
Phone Number
Phone Number
Enter the Secondary Central Station Phone Number
Account Number
FFFF
Account Number
Enter the Secondary Central Station Account Number
Dynamic Priority
None
Dynamic Priority
Redundant Reports
Preferred Telco
Preferred Radio
Note: If Preferred Telco or Preferred Radio is selected the Dynamic Delay option will be displayed.
Dynamic Delay
None
Dynamic Delay
None
15 Seconds
30 Seconds
60 Seconds
90 Seconds
Report All
Press to Report All
Report All
Press to Report All
Report All Set
Report Alarms
Enabled
Report Alarms
Disabled
Enabled
Report Troubles
Disabled
Report Troubles
Disabled
Enabled
Report Open/Close
Disabled
Report Open/Close
Disabled
Enabled
Report Tests
Enabled
Report Tests
Disabled
Enabled
Follow Me Phone 1
Follow Me Phone 1
Choose from the following options:
Phone Type Phone Number
Report All Report Alarms
Report Troubles Report Open/Close
Report Tests
Phone Type
None Phone Type
None
Follow me
Phone Type
None Phone Number
Enter the Follow Me Phone Number
Report All
Press to Report All
Report All
Press to Report All
Report All Set