Honeywell Lynx Touch L5100 User manual

Lynx Touch – L5100
Technical Training
WiFi Setup

2 HONEYWELL - CONFIDENTIAL File Number
WiFi General Information
•Is compatible with the New Honeywell WAP-PLUS
-Does not work with the Honeywell WAP (initially)
•Does not work with the Sercom router sold under
Honeywell brand through ADI (Sercom has a work
around/fix)
•Does not support WPS (initially)
•Does not work with a router which does not transmit its
SSID (the router must transmit SSID)

3 HONEYWELL - CONFIDENTIAL File Number
Wi-Fi Router Compatibility Chart
•Some routers may not work in the initial release, a list of
routers supported will be part of release 1
communications
-Cisco E1500
-Netgear WNR2000 v3
-Dlink DIR-815
-Buffalo WHR-HP-GN (Amp using this one)
•Wi-Fi Certification
-Running change 3Q2012
•Recommended Encryption
-WPA2

4 HONEYWELL - CONFIDENTIAL File Number
Advanced Protection Logic
1. System armed 2. Entry delay starts 3. Signal sent to AlarmNet
4. If System is disarmed
within entry time, no signal is
sent to central station
or
5. Central Station Dispatches
Superior Implementation With APL
4. If System is Not disarmed
within entry time AlarmNet
sends signal to central station

5 HONEYWELL - CONFIDENTIAL File Number
WiFi Alarm Reporting
•After 1 hour of AC loss, the WiFi module shuts down to
preserve battery.
•Reports may take up to 60 seconds to report, even if
GSM is used as back up (60 seconds is the time for
WiFi to wake up, scan for networks, acquire an iP
address).
-Smash and grab will still work, just will take extra 60 seconds to
report. Smash and grab will not have an increased level of false
alarms due to the power save feature
•If router is down, for whatever reason, reports then go
over GSM but may not be until >60 seconds later (as the
Wi-Fi path is tried 1st)

6 HONEYWELL - CONFIDENTIAL File Number
WiFi Alarm Reporting (Cont.)
•If there is a smash and grab event, the WiFi module will
respond to the increased supervision, thus not creating
the new APL possible trouble alarm
•Entry delay and/or dial delay may add additional time to
the alarm report time (unless the WiFi wakes up after
event, rather than when the alarm needs to report out)
•While you get TC basic free with WiFi / ip, it will not work
during a power outage, even if GSM is the back up
(after the 1 hour as the WiFi module is asleep)

7 HONEYWELL - CONFIDENTIAL File Number
WiFi Setup
•WiFi Module Installed Speaker Side
-Power System Down Before Installation
-Must be mounted on the speaker side

8 HONEYWELL - CONFIDENTIAL File Number
WiFi Setup
•WiFi Network Connection
-Setup by Installer
-Reconfigured by Master
Installer Programming
•Communicator
-Select Communication Path
WiFi
WiFi & GSM
•Advanced Protection Logic
-Must Use AlarmNet Device as
Primary Communicator
IP
GSM
WiFi
WiFi & GSM GSM Fault time is defaulted to 60
minutes and can not be changed.

9 HONEYWELL - CONFIDENTIAL File Number
WiFi Setup
Installer Programming
•Communicator
Diagnostics
-Select Configure WiFi
•Scan Access Points
-Broadcasting Networks
•Manual Configure
-Non-Broadcasting Networks*
-Pre-Configuring
-Feature currently not
working
•NOTE:
-If the SSID is not
broadcasted, the WiFi will not
connect

10 HONEYWELL - CONFIDENTIAL File Number
WiFi Setup
Scan Access Points
•Touch Scan to Re-Scan
•Select Network and Touch
Edit to Configure and Join.
•Toggle Field Values by
Touching Each Field.
-Security, Infrastructure &
DHCP will be Detected
Automatically
•Touch Key to Enter
Network Passphrase or
Key

11 HONEYWELL - CONFIDENTIAL File Number
WiFi Setup
Scan Access Points
•Touch “Done” After
Entering the Network
Passphrase or Key.
•Touch “Save” to Save the
Network Settings.
•Touch “Join” to Join the
Network.

12 HONEYWELL - CONFIDENTIAL File Number
WiFi Setup
Manual Configure AP
•Used for Non-Broadcasting
Network Configuration
•Security
-Open
-WPA1
-WPA2
-WEP
•Network Type
-Infrastructure
-Ad-Hoc` (no WiFi required)
•DHCP
-Yes/No
-Configure Static Settings on Page 2 of Communicator Programming

13 HONEYWELL - CONFIDENTIAL File Number
WiFi Setup
•Configure WiFi via Master Tools Menu
-WiFi Config
•WiFi Configure Options
-Scan Access Points
-Manual Configure AP
•Only The Installer May
Setup Static Connectivity.
•All Steps Same to Join a
Wireless Network.
•If the SSID is not broadcasted,
the WiFi will not connect

14 HONEYWELL - CONFIDENTIAL File Number
WiFi Setup
•Power Reset Option
-Available for the end user
-More Tools {Master Code} Test Reboot
If Power Cycle is Required to Reconnect to Network

Lynx Touch – L5100
Technical Training
Android Tablet Setup

16 HONEYWELL - CONFIDENTIAL File Number
Tablet General Information
•Does not support programming modes (Master user
screen, Installer program screens, and Advanced Z-
wave screens)
•Can be used with Tuxedo
•Can be learned in many panels (vacation and main
home)
•4 tablets per panel (must be learned in)
•App for Android Market will be available in May (Appr.)
•App for Apple will be available in Dec. (Appr.)

17 HONEYWELL - CONFIDENTIAL File Number
Android Tablet Setup
The MID-7H Tablet Used to Access to View and Control
the Lynx Touch 5100 and Z-Wave Devices.
•L5100 Must Have Installed One of the Following:
-L5100-WIFI
-ILP5
•WiFi Required Onsite for MID-7H Tablet Connection
-No Remote Connectivity

18 HONEYWELL - CONFIDENTIAL File Number
Android Tablet Setup
Enable & Connect Tablet to WiFi Network
•Go to Settings on Tablet by Selecting the “Settings” Icon.

19 HONEYWELL - CONFIDENTIAL File Number
Android Tablet Setup
Enable & Connect Tablet to WiFi Network
•From Settings, select “Wireless Networks”.

20 HONEYWELL - CONFIDENTIAL File Number
Android Tablet Setup
Enable & Connect Tablet to WiFi Network
•On this Page, Make Sure a Check Mark Appears in the
Wi-Fi Box; If Not, Select the Box to Enable.