Honeywell RCWL200A User manual

Installation
Instructions
RCWL200A and RCWL210A
Portable Chime (51375SL; 51376SL) With Push (51381SL)
69-2112EFS-07

Installation Instructions
69-2112EFS—07 ii
M27177
FLASHING LIGHT (FOR
RCWL210A ONLY)
VOLUME CONTROL
SWITCH
LED
PROGRAMMING
BUTTON
FLASHING LIGHT AND SOUND
SELECTION SWITCH (FOR
RCWL210A ONLY)
LED INDICATES
TRANSMITION
PUSH BUTTON
M27176

RCWL200A and RCWL210A
1 69-2112EFS—07
• Chime
• Bellpush
• CR2032batteryforbellpush
• 2xscrewsforpush
• 2xwallplugs
• Adhesivepad
Youwillneed:
• 3XLR14Csize1.5VAlkaline
batteries
• A#1Philips-headscrewdriver
• Asmallflatbladedscrewdriver
• A1/4-in.(6mm)drillbit
Safety
Beforeproceedingwiththeinstallation,pleasenotethefollowingsafetywarnings:
• Alwaysfollowthemanufacturer’sadvicewhenusingpowertoolsandwear
suitableprotectiveequipment(e.g.safetygoggles)whendrillingholes,etc.
• Beforedrillingholesinwalls,checkforhiddenelectricitycablesandwaterpipes.
Theuseofacable/pipelocatorisadvisableifindoubt.
Batteries(batterypackorbatteriesinstalled)shallnotbeexposedtoexcessiveheat
suchassunshine,fireorthelike;dangerofdamageifbatteryisincorrectlyreplaced.
Replaceonlywiththesameorequivalenttype.
1. Checking Pack Contents

Installation Instructions
69-2112EFS—07 2
2. Installing Batteries
+–
+
–
M27178
+–
LR14 C SIZE
M27182
CR2032
+
CR2032
+

RCWL200A and RCWL210A
3 69-2112EFS—07
3. Change Tune or Program New Push
Pressandreleaseprogrammingbutton,LEDwillilluminate,presspushbuttontohear
thetune.Presspushbuttonagaintohearanothertune.
Tosavethetuneselected,press
andreleaseprogrammingbutton.
Note:Pressingtheprogrambuttonformorethan15sec
willeraseallmemory.Followstep3tore-program.
M27145
M27183

Installation Instructions
69-2112EFS—07 4
4. Install Back Cover Using Screws or Adhesive Pad Provided
TOP
TOP
M27184
Note:Beforefinalinstallationadjustdistanceandposi-
tionbetweenpushandchimetooptimizethechime
withinyourenvironment.Densewallsandmetalcan
reducerange.
Wall Type Range Reduction
Dry-linedpartitionwall 10–30%
Single-layerbrickwall 20–40%
Double-layerbrickwall 30–70%
Metalpanel/radiator 90–100%

RCWL200A and RCWL210A
5 69-2112EFS—07
5. Volume Adjustment

Installation Instructions
69-2112EFS—07 6
6. Strobe and Sound Selections
Lightandsoundselection(applicabletoRCWL210Aonly).
M27180

RCWL200A and RCWL210A
7 69-2112EFS—07
7. Low Battery Indication
Tune+2beeps+2LEDflashes=changebatteriesinchime.
Tune+3beeps+3LEDflashes=changebatteryinpush.
M27181
+–
+
–
+–
+BEEP2
+BEEP3
+
+
x 2
x 3
CR2032
+
CR2032
+

Installation Instructions
69-2112EFS—07 8
Specification Chime Bell Push
OperatingTemperature 32°Fto104°F
0°Cto+40°C 14°Fto104°F -10°Cto+40°C
RFFrequency–US 345MHz 345MHz
Range(openfield) 200ft(61m)
SoundLevel(typical) 82dBA@3ft(1m)
RFPower <1mW
BatteryType LR14Csize CR2032
BatteryLife
(5operations/day) 12months 18months
WaterProof PassULraintest
Tunes
DingDong
4notesModern
8notesWestminster
SaxophoneSound