Honeywell X-618 User manual

M_XXXXXX_EN_1.0
X-618 Public Address and Voice
Alarm System
Installation Manual

i
Copyright
© 2012 Honeywell International Inc. All rights reserved.
No part of this document may be reproduced in any form without the written permission of the
copyright owner.
Disclaimer
The contents of this document are subject to revision without notice due to continued progress in
methodology, design, and manufacturing. Honeywell shall have no liability for any error or damage
of any kind resulting from the use of this document.
Trademark List
All trademarks mentioned herein are the property of their respective owners. These are shown in
the document Trademark Information.

Safety Guidelines
Danger
This sign reminds users of “dangerous voltage” on the product.
Caution
This sign reminds users of important instructions attached to the product.
Safety guideline
In order to prevent electric shock, this equipment plug shall not be used
as conductor to extend power supply line.
Do not block the equipment’s ventilation opening or put other equipment
on it.
Safety guideline Protect this equipment against rainwater or moisture so as to avoid fire
or electric shock.
Safety Precautions
Please carefully read and observe the following precautions before installing, operating or using
this product.
Electricity Utilization Safety
Local electrical safety regulations must be observed for product installation and operation.
The Company shall not be liable for fire or electric shock accidents caused by incorrect
installation and mistake.
Transportation Safety
The product shall be protected against impact, violent vibration or liquid erosion during
transportation, storage and installation.
Environmental Requirements
Do not install the product within the environment of extreme temperature or dust and
mechanical vibration.
This equipment shall be well ventilated and protected against dust, moisture, direct sunshine
and violent during the use. It shall be kept away from radiating objects or heat sources
and well ventilated. The optimum working environment temperature is 5-28ºC and relative

humidity <95%. If the equipment is in operation for a long time and ambient temperature is too
high, it is recommended that effective measures should be taken to reduce temperature.
Requirements on grid power supply voltage by the equipment: AC 220V (-15% to +10%) 50-
60Hz. In case of too high, too low voltage or that fluctuating greatly, it is recommended that AC
regulated power supply should be installed.
As the product is not waterproof, do not expose it to rainwater or liquid environment so as to
avoid damaging it.
Put the equipment on solid level plane or install it on a rack.
Do not put other articles on the equipment top.
Safe Use Precautions
The equipment shall be installed under the direction of professionals.
Please carefully check power supply lines for damage prior to use. The lines must be
connected to the equipment in strict accordance with identifications.
Power supply plugs and sockets shall match each other. Otherwise, suitable sockets must be
provided. Human damage to the sockets shall be prohibited.
Power supply for the equipment shall be provided with sufficient capacity and independent and
reliable grounding lines.
Please ensure the equipment power supply grounding lines interconnected and
connected with the ground. Otherwise, it will cause it abnormal, even damaged.
There are HV lines within it. When turn on the power, do not open the equipment cover without
permission so as to prevent electric shock.
Prior to the first energization to start equipment, please check its external wiring for
correctness so as to avoid damage.
During the energization, please do not touch wiring terminals identified with “lightning” at
random so as to avoid electric shock.
Please do not change equipment connection circuits at random during energization so as to
avoid damage.
In case of failure to the equipment, please ask professional repair personnel to repair it.
Otherwise, the Company shall neither dispose of any problems nor undertake relevant
responsibilities.
Label and User’s Manual
Please pay attention to information on the product label such as type and power supply.
Please carefully read the user’s manual and operate according to the instructions. The user’s
manual is for reference for operation of products of different types. Specific operations of
products of different types are not listed herein. In case of any problem, please contact the
Company.
Please maintain this Manual for future reference.

Table of Contents
Safety Guidelines..................................................................................................................................ii
Safety Precautions............................................................................................................................ ii
Electricity Utilization Safety......................................................................................................... ii
Transportation Safety ................................................................................................................. ii
Environmental Requirements ..................................................................................................... ii
Safe Use Precautions................................................................................................................ iii
Label and User’s Manual........................................................................................................... iii
Preface ...................................................................................................................................................1
Brief Introduction...............................................................................................................................1
Intended Audience............................................................................................................................1
Relevant Documents.........................................................................................................................1
Use Instructions ................................................................................................................................1
1 System Overview ............................................................................................................................3
2 Preparation for Installation............................................................................................................4
Gathering Information.......................................................................................................................4
Preparing Tools.................................................................................................................................4
Preparing Auxiliary Materials............................................................................................................5
Preparing Cables and Auxiliary Equipment......................................................................................5
Packing List Inspection.....................................................................................................................7
3 System Installation .........................................................................................................................7
Installing the NPM on a Fixed Surface (Optional).............................................................................7
Connecting the Protective Grounding Cabinet Wires.......................................................................8
Installing the DCS and DA in the Appliance Cabinet........................................................................9
Connecting the Protective Grounding Appliance Wires..................................................................10
Connecting the X-618 System Components...................................................................................10
Connecting the Sound Source Equipment to the DCS.............................................................11
Connecting the DCS to the DA.................................................................................................11
Connecting the Dry Contacts (Optional)...................................................................................14
Connecting the Noise Detector (Optional)................................................................................15
Connecting the Loudspeakers..................................................................................................16
Connecting the DCS to the NPM..............................................................................................16
Connecting the Power Supply Cables ............................................................................................17
DCS Main and Standby Power Supply Cables.........................................................................18
DA Main and Standby Power Supply Cables ...........................................................................19
NPM Power Supply Cable ........................................................................................................19
4 Installation Inspection..................................................................................................................20
Inspection........................................................................................................................................20

1
Preface
Thank you for purchasing the X-618 Public Address and Voice Alarm System. Please carefully
read this manual prior to system use so as to ensure correct use of the system.
Brief Introduction
This manual describes the appearance, installation, and wiring of the X-618 Public Address and
Voice Alarm System equipment. The manual includes the following chapters:
Chapter 1: System Overview
Describes the X-618 Public Address and Voice Alarm System structure and product assembly
Chapter 2: Preparation for Installation
Describes preparing to install the X-618 Public Address and Voice Alarm System
Chapter 3: System Installation
Describes installing the X-618 Public Address and Voice Alarm System along with related
precautions
Chapter 4: Installation Inspection
Describes inspecting the installation of the X-618 Public Address and Voice Alarm System and
system commissioning
Intended Audience
This manual is mainly for personnel who are to install, operate, and maintain the X-618
Broadcasting and Voice Alarm System.
Relevant Documents
The following documents can be used as a reference when reading this manual:
X-618 Public Address and Voice Alarm System Product Description
X-618 Public Address and Voice Alarm System Configuration Manual
X-618 Public Address and Voice Alarm System Operation Manual
Use Instructions
All content including figures in this manual are to be used only for reference.
The product may be subject to change from time to time without notice.
Users of this product are recommended to carefully read all warnings and precautions in this
manual.
Carefully read this manual before using the product and keep it as a reference for future use.
This manual has been reviewed with its accuracy is ensured. In case of any doubt or dispute
of the product description, the final interpretation given by the Life Safety A/V (Guangzhou)
Co., Ltd. shall prevail.

2
The Life Safety A/V (Guangzhou) Co., Ltd is not liable for any consequences caused by user
mistakes when using the product or user misunderstandings of the manual content.

3
1 System Overview
The X-618 Public Address and Voice Alarm System provides a complete multiple sound source
public audio management solution. Centralized network management is achieved through the
system software, and all system states are monitored. The X-618 Public Address and Voice Alarm
System is hereby referred to as the “X-618” throughout the remainder of this manual.
The X-618 includes the following product components:
X-DCS2000 Digital Integrated System Manager
The X-DCS2000 Digital Integrated System Manager is hereinafter referred to as the “DCS” or
“X-DCS2000”.
The DCS is X-618 control equipment designed for expanding the number of loudspeaker
zones, and can support multiple sound source files for broadcasting. The system
integrates with functions such as the sound source file storage system, the network audio
broadcasting system, the loudspeaker zone control system, and the system for monitoring and
diagnosing faults.
X-DA2250 High Efficiency Power Amplifier
The X-DA2250 High Efficiency Power Amplifier is hereinafter referred to as the “DA” or “X-
DA2250”.
In the X-618 system, the DA is used to amplify audio signal power and drive many
broadcasting loudspeakers.
X-NPMI Configurable Network Paging Console
The X-NPMI Programmable Network Paging Console is hereinafter referred to as the “NPM”
or “X-NPMI”.
The NPM is used to page zones and control broadcasts for the X-618 on an Ethernet network.
Figure 1 shows the schematic diagram of the X-618 system structure.

4
Figure 1 Schematic Diagram of the X-618 System
2 Preparation for Installation
Before installing the system, appropriate preparation is required to ensure a smooth installation
process.
Gathering Information
Preparing Tools
Preparing Auxiliary Materials
Preparing Cables and Auxiliary Equipment
Packing List Inspection
Gathering Information
Installation personnel are required to be familiar with functional components of the X-618 product
equipment. It is recommended to first read the product information found in the X-618 Public
Address and Voice Alarm System Product Description.
Preparing Tools
Prepare the following tools before installing the system equipment:
Electrostatic proof wrist band
Electrostatic proof gloves

5
Wire stripping pliers
Wire cutting pliers
RJ45 crimp tool
Slotted screwdriver (M2)
Phillips screwdriver (P1)
Preparing Auxiliary Materials
Prepare the following auxiliary materials before installing the system equipment:
Insulating tape
Wire buckles
Cable labels
Plastic ties
Preparing Cables and Auxiliary Equipment
Note:
It is recommended to select high quality and professional-grade transmission cables for large scale
loudspeaker systems.
The longer the distance, the thicker the cable must be used, as more power is required to transmit
the data. Please select appropriate cables according to the distances involved.
Prepare the following cables and auxiliary equipment before installing the system equipment:
CAT-5 Ethernet cable
Cables are required to be no longer than 100m with diameters of 0.51mm (wire gauge of
24AWG). Shielded twisted pair cables are recommended.
Refer to Table 1 for the Ethernet pin types.
Table 1 RJ45 Cable Pin Definition Descriptions
PIN Type Legend
1 TX+
2 TX-
3 RX+
4 No pin
5 No pin
6 No pin
7 RX-
8 No pin
100V audio connection cable

6
This cable is used to connect the DCS to the DA as well as the DCS to the loudspeakers in the
broadcasting zones. Shielded cables with a cross-section of 1.3mm2(wire gauge of 16AWG)
are recommended to connect the external sound source devices, such as CD/DVD players
and tuners.
DA standby power supply cable
The DA standby power supply cable specification is required to be the same as that of the
main power supply line.
Power amplifier audio input cable
Audio input cables are provided in the package containing the DA, but the lengths of these
cables are limited. If these cables cannot meet the requirements of the system wiring situation,
users need to obtain or create appropriate cables themselves. Please create such audio input
cables with the specifications as listed in Table 2.
Table 2 Power Amplifier Input Cable Pin Definition Descriptions
PIN Type Legend
1 Audio positive pole of Channel 2
2 Audio negative pole of Channel 2
3 Power amplifier failure signal
4 Audio positive pole of Channel 1
5 Audio negative pole of Channel 1
6 Signal grounding (0V))
7 DC 24V power supply
8Self-test signal
Power amplifier output cables
Unshielded cables with a cross-section of 1.3mm2(wire gauge of 16AWG) are recommended
for the power amplifier output.
Table 3 Power Amplifier Output Cable Pin Definition Descriptions
PIN Type
1 100V output of audio negative pole of Channel 2
2 Audio positive pole of Channel 2
3 Power amplifier failure signal
4 100V output of audio negative pole of Channel 1
5 Audio positive pole of Channel 1
Dry contact input/output cables and related external equipment (optional)
The necessity of dry contact connections depends on the system situation. If the DCS and
external equipment, such as three-wire volume controllers and four-wire single-channel
controllers, must be connected through dry contacts, this equipment and the appropriate
cables must be prepared beforehand.
Noise detector (optional)
When needing to collect environmental noise and automatically control the volume of
broadcasts, a noise detector and appropriate cables must be prepared. The maximum cable
distance between the DCS and noise detector is required to be no more than 250m, and
shielded twisted pair cables must be used.

7
Packing List Inspection
Please check the external packages for intactness before unpacking them for content inspection.
Use the “Packing list” to check the package contents. Contact the carrier or supplier promptly in
case of any package or package content problems.
3 System Installation
This chapter describes the system equipment installation, cable connections, and relevant
precautions.
Installing the NPM on a Fixed Surface (Optional)
Connecting the Protective Grounding Cabinet Wires
Installing the DCS and DA in the Appliance Cabinet
Connecting the Protective Grounding
Connecting the X-618 System Components
Connecting the Power Supply
Note:
The electricity and power sources must be turned off when performing the following tasks to avoid
electric shocks and damage to the equipment.
Turn off all equipment power supply switches prior to wiring.
Correctly connect the wiring terminals and tighten the screws.
The power supply cables and signal data lines must be separated, and cannot be laid in the same
slot or piping.
Control signal cables must be positioned away from 100V audio or power supply cables to avoid
signal interference.
Appropriate materials, such as plastic ties, must be used for all connection cables for
reinforcement to avoid looseness. When moving the cables, prevent the power supply cables from
coming in contact with the signal data cables.
Install appropriate electrical cables bushings at the cabinet opening before installing the cables in
the appliance cabinets.
Appropriate materials must be used to block the spaces reserved for the cables at the cabinet
opening if these spaces are not used.
Installing the NPM on a Fixed Surface (Optional)
If it is unnecessary to move the NPM often, embed the NPM in a fixed surface, such as a desk.
The installation steps are as follows:
1. Cut a slot for the NPM to fit in on the desk surface. The slot is required to be 198mm long and
100mm wide, as shown in Figure 2.

8
Figure 2 Schematic Diagram of Creating a Slot for Seating the NPM (Level Surface)
Figure 3 Schematic Diagram of Creating a Slot for Seating the NPM(Slanted Surface)
2. Adequate space for wires connecting to the NPM must be reserved on the rear side of the unit.
If the surface thickness is greater than 10mm, the space reserved for the wires must be about
80mm long and 10mm wide, as shown in Figure 4.
Figure 4 Schematic Diagram of the Reserved Space for the Rear Panel Wire Connections
3. Installing the Microphone Pole
Connect the microphone pole at one end in the gooseneck microphone socket of the NPM,
and tighten the pole, as show in Figure 5.
Figure 5 Microphone Pole Installation Diagram
Connecting the Protective Grounding Cabinet Wires
The cabinet door shaft contains one yellow grounding wire as shown in Figure 6, identified with a
○
1 . Figure 6, marker ○ 2 , represents another grounding terminal in the same position in the
cabinet. Connect the grounding wire to the two terminals.
Caution:
To prevent a grounding loop, be careful to not let a short-circuit occur over the grounding wires.

9
Figure 6 Schematic Diagram of Cabinet Grounding
Installing the DCS and DA in the Appliance Cabinet
Install the DCS and DA into the associated appliance cabinet. This process is described in the
following steps:
1. Connect and hang the emergency microphone in place on the front panel of the DCS. An
installed emergency microphone is shown in Figure 7.
Figure 7 PTT Microphone Installation Diagram
2. Install brackets on the left and right sides of the DCS, as shown in Figure 8.
Figure 8 Schematic Diagram of the DCS Bracket Installation
3. Put the DCS appliance into the cabinet, and tighten the screws to secure the unit, as shown in
Figure 9.

10
Figure 9 Schematic Diagram of Installing the DCS in the Cabinet
4. Install brackets on the left and right sides of the DA, as shown in Figure 8.
5. Install the DA appliance into the cabinet, and tighten the screws to secure the unit, as shown
in Figure 9.
Note:
1U (1U=44.45mm) of space is required right above the DA to allow for proper appliance ventilation.
It is recommended to use an empty panel to close and open the installation space of the cabinet.
Connecting the Protective Grounding Appliance Wires
The DCS and DA grounding terminals must be connected to the terminal blocks through flexible
cables with a cross-section of 1.5mm2within the cabinet, as shown in Figure 6.
Notice:
Do not connect the grounding output cable with the grounding input cable as a short circuit can
occur.
Connecting the X-618 System Components
This section describes the connections between the following X-618 system components:
Connecting the Sound Source Equipment to the DCS

11
Connecting the DCS to the DA
Connecting the DCS to the NPM
Connecting the Dry Contacts (Optional)
Connecting the Dry Contacts (Optional)
Connecting the Noise Detector (Optional)
Connecting the Sound Source Equipment to the DCS
Connect the external sound source equipment to the DCS appliance as necessary.
Figure 10 Schematic Diagram of Connecting the DCS External Sound Source Equipment
Connecting the DCS to the DA
Note：
The DCS can be connected to the power amplifier in the following configurations:
Connect the PA1/2 and PA2 port of the single-channel power amplifier to the DCS control port
using two network cables.
Connect the PA1/2 port of the two-channel power amplifier to the DCS control port using one
network cable. Refer to Figure 11.
Connect the PA1/2 and P3/4 port of the four-channel power amplifier to the DCS control port
using two network cables.
1. Connect the DA RJ45 port to the DCS control port using the audio input lines that are included
in the package containing the DA, as shown in Figure 11.
Figure 11 Connecting the RJ45 Audio Cable to the DCS and DA

12
2. Connecting the DA audio output to the DCS
a. Strip one end of the prepared audio output cable jacket by 10mm, and feed the cable
through the DCS protective cover of the terminal, as shown in Figure 12.
Figure 12 Schematic Diagram of a Feeding the Audio Output Cable Through the
Protective Terminal Cover
b. Take the end of the cable that was fed through the protective cover of the DCS wiring
terminal connect the cable to the power amplifier output wiring terminal (7P green phoenix
tail seating 5.08mm), and tighten the screws. Refer to Figure 13.
Figure 13 Connecting the Audio Output Cable to the Power Amplifier Input Wiring
Terminal
c. Feed the other end of the audio output cable through the protective cover of the power
amplifier. Refer to Figure 12.
d. Connect the end of the cable that was fed through the protective cover of the power
amplifier to the power amplifier input wiring terminal (4P green phoenix tail seating
5.08mm), and tighten the screws. Refer to Figure 13.
e. Insert the power amplifier audio output wiring terminal of the installed audio output cable
into the DA audio output port, as shown in Figure 14.

13
Figure 14 Schematic Diagram of the Audio Output Wiring Terminal Installation
f. Insert the power amplifier input wiring terminal of the installed audio output cable into
the DCS PA audio input port, as shown in Figure 15.
Figure 15 Schematic Diagram of the Audio Input Wiring Terminal Installation
g. Cover the power amplifier terminal with the protective terminal cover and tighten the
screws, as shown in Figure 16. This same operation applies to the DCS terminal and
related protective cover.

14
Figure 16 Schematic Diagram of the Protective Audio Input Terminal Cover
Connecting the Dry Contacts (Optional)
This section describes connecting the external equipment or switch through the dry contacts.
Dry Contact Input Preparation
1. Connect the dry contact cable to the dry contact input terminal.
Strip the wire jacket off one end of the prepared dry contact connection cable by about 10mm,
insert the wires into the dry contact wiring terminal (8P green phoenix tail seating 3.81mm),
and tighten the screws. Refer to Figure 13 for more information.
2. Insert the dry contact input wiring terminal of the installed input cable into the DCS dry contact
port. Refer to Figure 14.
3. Connect the external dry contact equipment or switch to the other end of the dry contact input
cable, as shown in Figure 17.
Figure 17 Connect External Dry Contact or Switch