Horizon Fitness ELITE T7 User manual

ASSEMBLY GUIDE
GUIDE D’ASSEMBLAGE
GUÍA DE ENSAMBLAJE
ELITE T7
T9
HZ14_AG_Elite_T7_T9_r1_2.indd 1 7/2/14 3:55 PM

32
SERIAL NUMBER LOCATION
ASSEMBLY
There are several areas during the assembly process that special attention must be paid. It is very important to follow the
assembly instructions correctly and to make sure all parts are firmly tightened. If the assembly instructions are not followed
correctly, the treadmill could have parts that are not tightened and will seem loose and may cause irritating noises. To
prevent damage to the treadmill, the assembly instructions must be reviewed and corrective actions should be taken.
Before proceeding, find your treadmill’s serial number located on a white barcode sticker
near the on/off power switch and power cord and enter it in the space provided below.
ENTER YOUR SERIAL NUMBER AND MODEL NAME IN THE BOXES BELOW:
» Refer to the SERIAL NUMBER and MODEL NAME when calling for service.
SERIAL NUMBER:
TM
MODEL NAME: HORIZON TREADMILL
WARNING
3 ENGLISH
16 FRANÇAIS
30 ESPAÑOL
HZ14_AG_Elite_T7_T9_r1_2.indd 2-3 7/2/14 3:55 PM

54
T7
1
2
CONSOLE DISPLAY
AND CONTROLS
WATER BOTTLE HOLDER
CONSOLE
SPEAKERS
ON/OFF SWITCH
POWER CORD
HEART RATE GRIP BARS
TRANSPORT WHEEL
FOOT LOCK LATCH (UNDERNEATH DECK)
CONSOLE FAN
READING RACK
HANDLEBARS
CONSOLE MAST
SAFETY KEY PLACEMENT
MOTOR COVER
RUNNING BELT / DECK
REAR ROLLER TENSION
& ADJUSTMENT BOLTS
SIDE RAIL
T9
1
2
CONSOLE DISPLAY
AND CONTROLS
WATER BOTTLE HOLDER
CONSOLE
SPEAKERS
ON/OFF SWITCH
POWER CORD
HEART RATE GRIP BARS
TRANSPORT WHEEL
FOOT LOCK LATCH (UNDERNEATH DECK)
CONSOLE FAN
READING RACK
HANDLEBARS
CONSOLE MAST
SAFETY KEY PLACEMENT
MOTOR COVER
RUNNING BELT / DECK
REAR ROLLER TENSION
& ADJUSTMENT BOLTS
SIDE RAIL
HZ14_AG_Elite_T7_T9_r1_2.indd 4-5 7/2/14 3:55 PM

76
1
A
ASSEMBLY STEP 1
A Cut the yellow banding straps and lift the
running deck upward to remove all contents
from underneath the running deck.
B Open hardware for STEP 1.
C Insert 2 BOLTS (A) into MAIN FRAME (1).
HARDWARE FOR STEP 1
PART TYPE QTY
A HEX SOCKET BOLT 2
TOOLS REQUIRED:
FT-Wrench
FL-Wrench
FPhillips Screwdriver (not included)
PARTS INCLUDED:
F1 Main Frame
F2 Console Masts
F1 Console
F2 Water Bottle Holders
F2 Handlebars
F2 Main Frame Covers
F2 Console Mast Covers
F1 Polar®Chest Strap
F1 Hardware Kit
F1 Safety Key
F1 Power Cord
F1 Audio Adapter Cable
If you have questions or if there
are any missing parts, contact
Customer Tech Support. Contact
information is located on the
back cover of this manual.
NEED HELP?
• DO NOT ATTEMPT TO LIFT THE TREADMILL! Do not move or lift treadmill
from packaging until specified to do so in the assembly instructions. You may
remove the plastic wrap from console masts.
• FAILURE TO FOLLOW THESE INSTRUCTIONS COULD RESULT IN INJURY!
WARNING
UNPACKING
Place the treadmill carton on a level flat surface. It is recommended that you place
a protective covering on your floor. Take CAUTION when handling and transporting
this unit. Never open box when it is on its side. Once the banding straps have been
removed, do not lift or transport this unit unless it is fully assembled and in the upright
folded position, with the lock latch secure. Unpack and assemble the unit where it
will be used. The enclosed treadmill is equipped with high-pressure shocks and may
spring open if mishandled. Never grab hold of any portion of the incline frame and
attempt to lift or move the treadmill.
PRE ASSEMBLY
• During each assembly step, ensure that ALL nuts and bolts are in place and
partially threaded. It is recommended you complete the full assembly of your
unit before completely tightening any ONE bolt.
• Several parts have been pre-lubricated to aid in assembly and usage. Please
do not wipe this off. If you have difficulty, a light application of lithium bike
grease is recommended.
IMPORTANT NOTES
HZ14_AG_Elite_T7_T9_r1_2.indd 6-7 7/2/14 3:55 PM

98
A Pull the CONSOLE CABLE (3) away from the
treadmill base frame. Connect the CONSOLE
CABLE (3) from the MAIN FRAME (1) to the
CONSOLE CABLE (3) in the bottom of the
RIGHT CONSOLE MAST (4). The other end of
the CONSOLE CABLE should be located at the
top of the mast.
B Open HARDWARE FOR STEP 3.
C Attach RIGHT CONSOLE MAST (4) to MAIN
FRAME (1) using 4 BOLTS (B), 4 SPRING
WASHERS (C) and 4 FLAT WASHERS (D).
4
3
B
1
C
D
ASSEMBLY STEP 3
HARDWARE FOR STEP 3
PART TYPE QTY
B BUTTON HEAD BOLT 4
CSPRING WASHER 4
DFL AT WASHER 4
NOTE: Do not fully tighten bolts until step 6.
NOTE: Be careful not to pinch the console
cable while attaching the right console mast.
2
1
D
C
B
ASSEMBLY STEP 2
A Open HARDWARE FOR STEP 2.
B Attach LEFT CONSOLE MAST (2) to MAIN
FRAME (1) using 4 BOLTS (B), 4 SPRING
WASHERS (C) and 4 FLAT WASHERS (D).
HARDWARE FOR STEP 2
PART TYPE QTY
B BUTTON HEAD BOLT 4
CSPRING WASHER 4
DFL AT WASHER 4
NOTE: Do not fully tighten bolts until step 6.
HZ14_AG_Elite_T7_T9_r1_2.indd 8-9 7/2/14 3:55 PM

1110
7
E
C
D
F
4
ASSEMBLY STEP 5
A Open HARDWARE FOR STEP 5.
B Place RIGHT HANDLEBAR (7) into top of
RIGHT CONSOLE MAST (4).
C Insert 1 BOLT (E), 1 SPRING WASHER (C)
and 1 FLAT WASHER (D) from the front-facing
side of the CONSOLE MAST (4).
D Insert 1 BOLT (E), 1 SPRING WASHER (C)
and 1 FLAT WASHER (D) from the inside-
facing side of the CONSOLE MAST (4).
E Insert 1 BOLT (E), 1 SPRING WASHER (C)
and 1 ARC WASHER (F) from the rear-facing
side of the CONSOLE MAST (4).
F Repeat steps B–E on other side.
HARDWARE FOR STEP 5
PART TYPE QTY
E BUTTON HEAD BOLT 6
CSPRING WASHER 6
DFL AT WASHER 4
FARC WASHER 2
NOTE: Do not fully tighten bolts until step 6.
5
4
6
A T7 models only: Slide MAIN FRAME COVERS
(5) over CONSOLE MASTS (4).
B All models: Slide CONSOLE MAST COVERS
(6) over CONSOLE MASTS (4).
NO HARDWARE FOR STEP 4
ASSEMBLY STEP 4
HZ14_AG_Elite_T7_T9_r1_2.indd 10-11 7/2/14 3:55 PM

1312
8
9
6
H
I
ASSEMBLY STEP 7
A Open HARDWARE FOR STEP 7.
B Slide CONSOLE MAST COVERS (6) up and
attach to masts using 4 SCREWS (H).
C Insert CONSOLE POCKETS (9) into
CONSOLE (8) and attach using 2 SCREWS (I).
HARDWARE FOR STEP 7
PART TYPE QTY
HSCREW 4
ISCREW 2
T7 ASSEMBLY COMPLETE!
3
4
8
2
D
C
G
ASSEMBLY STEP 6
A Open HARDWARE FOR STEP 6.
B Gently place CONSOLE (8) on top of
CONSOLE MASTS (2 & 4).
C Connect the CONSOLE CABLES (3) and
ensure cables are inside the right CONSOLE
MAST (4).
D Connect the CONSOLE (8) to the right
CONSOLE MAST (4) using 2 BOLTS (G),
2 SPRING WASHERS (C) and 2 FLAT
WASHERS (D).
E Repeat STEP D on left side.
HARDWARE FOR STEP 6
PART TYPE QTY
G BUTTON HEAD BOLT 4
CSPRING WASHER 4
DFL AT WASHER 4
NOTE: Be careful not to pinch the console
cables while attaching the console.
HZ14_AG_Elite_T7_T9_r1_2.indd 12-13 7/2/14 3:55 PM

1514
H
5
11
10
1
ASSEMBLY STEP 8 (T9 ONLY)
*This step is for T9 models only.
A Fold the deck into the upright position until the
FOOT LATCH (10) engages.
B Open HARDWARE FOR STEP 8.
C Silde the MAIN FRAME COVERS (5) down
over the MAIN FRAME (1). The notches on
the inside of the covers should align with the
SPACERS (11).
D Attach MAIN FRAME COVERS (5) to MAIN
FRAME (1) using 4 SCREWS (H).
E While holding the deck with both hands, press
the FOOT LATCH (10) with your foot to lower
the deck to the ground.
HARDWARE FOR STEP 8
PART TYPE QTY
HSCREW 6
T9 ASSEMBLY COMPLETE!
T9
HZ14_AG_Elite_T7_T9_r1_2.indd 14-15 7/2/14 3:55 PM

1716
EMPLACEMENT DU NUMÉRO
DE SÉRIE
ASSEMBLAGE
Le processus d'assemblage comporte certaines étapes au cours desquelles il faut faire particulièrement attention. Il est très
important de suivre correctement les instructions d'assemblage et de s'assurer que toutes les pièces sont bien serrées. Si
les instructions d'assemblage ne sont pas suivies à la lettre, certaines parties du tapis roulant pourraient être mal serrées et
bouger, et ainsi causer des bruits irritants. Afin d'éviter que le tapis roulant ne se brise, relisez les instructions d'assemblage
et prenez les mesures correctives qui s'imposent.
Avant de commencer, repérez le numéro de série de votre tapis roulant qui se trouve
sur un autocollant de code à barres blanc situé près de l'interrupteur marche/arrêt et du
cordon d'alimentation et inscrivez-le dans l'espace ci-dessous.
INSCRIVEZ LE NUMÉRO DE SÉRIE ET LE NOM DU MODÈLE DANS LES CASES
CI-DESSOUS :
» Reportez-vous au NUMÉRO DE SÉRIE et au NOM DU MODÈLE lors de tout appel à un service de réparations.
NUMÉRO DE SÉRIE :
TM
NOM DU MODÈLE : TAPIS ROULANT HORIZON
AVERTISSEMENT
FRANÇAIS
HZ14_AG_Elite_T7_T9_r1_2.indd 16-17 7/2/14 3:55 PM

1918
1
2
ÉCRAN ET COMMANDES
DE LA CONSOLE
PORTE-BOUTEILLE
D'EAU
CONSOLE
HAUT-PARLEURS
INTERRUPTEUR
MARCHE/ARRÊT
CORDON
D'ALIMENTATION
POIGNÉES DÉTECTANT
LA FRÉQUENCE
CARDIAQUE
ROULETTES DE TRANSPORT
PÉDALE DE VERROUILLAGE
(SOUS LA PLATEFORME)
VENTILATEUR DE CONSOLE
SUPPORT DE LECTURE
POIGNÉES
MONTANT DE CONSOLE
EMPLACEMENT DE LA CLÉ DE SÛRETÉ
COUVERCLE DU MOTEUR
COURROIE/PLATEFORME
DE COURSE
TENSION DU ROULEAU
ARRIÈRE ET BOULONS DE RÉGLAGE
GLISSIÈRE LATÉRALE
T9T7
1
2
ÉCRAN ET COMMANDES
DE LA CONSOLE
PORTE-BOUTEILLE
D'EAU
CONSOLE
HAUT-PARLEURS
INTERRUPTEUR
MARCHE/ARRÊT
CORDON
D'ALIMENTATION
POIGNÉES DÉTECTANT
LA FRÉQUENCE
CARDIAQUE
ROULETTES DE TRANSPORT
PÉDALE DE VERROUILLAGE
(SOUS LA PLATEFORME)
VENTILATEUR DE CONSOLE
SUPPORT DE LECTURE
POIGNÉES
MONTANT DE CONSOLE
EMPLACEMENT DE LA CLÉ DE SÛRETÉ
COUVERCLE DU MOTEUR
COURROIE/PLATEFORME
DE COURSE
TENSION DU ROULEAU
ARRIÈRE ET BOULONS DE RÉGLAGE
GLISSIÈRE LATÉRALE
HZ14_AG_Elite_T7_T9_r1_2.indd 18-19 7/2/14 3:55 PM