HP A-WA2610E-AGN Assembly instructions

EL-MF877-00 Page 1
Template Revision B
PSG instructions for this template are available at EL-MF877-01
Product End-of-Life Disassembly Instructions
Product Category: Networking Equipment
Marketing Name / Model
[List multiple models if applicable.]
HP A-WA2610E-AGN Single Radio 802.11n Plenum FIT Access Point (JD452A)
HP A-WA2620E-AGN Dual Radio 802.11n Plenum FIT Access Point (JD453A)
Purpose: The document is intended for use by end-of-life recyclers or treatment facilities. It provides the basic instructions
for the disassembly of HP products to remove components and materials requiring selective treatment, as defined by EU
directive 2002/96/EC, Waste Electrical and Electronic Equipment (WEEE).
1.0 Items Requiring Selective Treatment
1.1 Items listed below are classified as requiring selective treatment.
1.2 Enter the quantity of items contained within the product which require selective treatment in the right column, as
applicable.
Item Description Notes
Quantity
of items
included
in product
Printed Circuit Boards (PCB) or Printed Circuit
Assemblies (PCA)
With a surface greater than 10 sq cm
1
Batteries
All types including standard alkaline and lithium coin
or button style batteries
0
Mercury-containing components For example, mercury in lamps, display backlights,
scanner lamps, switches, batteries
0
Liquid Crystal Displays (LCD) with a surface greater
than 100 sq cm
Includes background illuminated displays with gas
discharge lamps
0
Cathode Ray Tubes (CRT)
0
Capacitors / condensers (Containing PCB/PCT)
0
Electrolytic Capacitors / Condensers measuring
greater than 2.5 cm in diameter or height
0
External electrical cables and cords
1
Gas Discharge Lamps
0
Plastics containing Brominated Flame Retardants
weighing > 25 grams (not including PCBs or PCAs
already listed as a separate item above)
0
Components and parts containing toner and ink,
including liquids, semi-liquids (gel/paste) and toner
Include the cartridges, print heads, tubes, vent
chambers, and service stations.
0
Components and waste containing asbestos
0
Components, parts and materials containing
refractory ceramic fibers
0
Components, parts and materials containing
radioactive substances
0

EL-MF877-00 Page 2
Template Revision B
PSG instructions for this template are available at EL-MF877-01
2.0 Tools Required
List the type and size of the tools that would typically be used to disassemble the product to a point where components
and materials requiring selective treatment can be removed.
Tool Description
Tool Size (if
applicable)
Screw driver
2#
3.0 Product Disassembly Process
3.1 List the basic steps that should typically be followed to remove components and materials requiring selective treatment:
1. Remove AP from accessories 7.
2. Remove the antenna 3 from base 1.
3. Unscrew the screws on cover 2, and then remove cover 2.
4. Remove all of the inner cables.
5. Unscrew the screws on press plate 4, and then remove press plate 4.
6. Remove the radio card 5 from base 1.
7. Unscrew the screws on PCB 6, and then remove PCB 6.
8. Remove thermal conductive pad 1-5 from base 1-1.
9. Unscrew the screws on heat sink 1-2, and then remove heat sink 1-2.
10. Remove film 1-3 from base 1-1.
11. Remove shielding finger 1-4 from base 1-1.
12. Remove wire saddle 1-6 from base 1-1.
13. Remove all of the labels.
14. Remove brand 2-1 from cover 2-2.
3.2 Optional Graphic. If the disassembly process is complex, insert a graphic illustration below to identify the items
contained in the product that require selective treatment (with descriptions and arrows identifying locations).
Figure 1 Treatments to the product

EL-MF877-00 Page 3
Template Revision B
PSG instructions for this template are available at EL-MF877-01
Figure 2 Treatments to the cover
Figure 3 Treatments to the base