HP ProCurve Radio Port 230 User manual

Installation and
Getting Started Guide
www.procurve.com
ProCurve Radio Port 230/210

© Copyright 2006-2007 Hewlett-Packard Development Company,
L.P. The information contained herein is subject to change with-
out notice.
This document contains proprietary information, which is
protected by copyright. No part of this document may be
photocopied, reproduced, or translated into another
language without the prior written consent of Hewlett-
Packard.
Publication Number 5991-8629
September 2007
Applicable Products
Trademark Credits
Windows NT®, Windows®, and MS Windows® are US
registered trademarks of Microsoft Corporation.
Disclaimer
HEWLETT-PACKARD COMPANY MAKES NO WARRANTY
OF ANY KIND WITH REGARD TO THIS MATERIAL,
INCLUDING, BUT NOT LIMITED TO, THE IMPLIED
WARRANTIES OF MERCHANTABILITY AND FITNESS
FOR A PARTICULAR PURPOSE. Hewlett-Packard shall not
be liable for errors contained herein or for incidental or
consequential damages in connection with the furnishing,
performance, or use of this material.
The only warranties for HP products and services are set
forth in the express warranty statements accompanying
such products and services. Nothing herein should be
construed as constituting an additional warranty. HP shall
not be liable for technical or editorial errors or omissions
contained herein.
Hewlett-Packard assumes no responsibility for the use or
reliability of its software on equipment that is not furnished
by Hewlett-Packard.
Warranty
See the Software License, Warranty and Support booklet
included with the product.
A copy of the specific warranty terms applicable to your
Hewlett-Packard products and replacement parts can be
obtained from your HP Sales and Service Office or
authorized dealer.
ProCurve Radio Port 230
ProCurve Radio Port 210
J9006A
J9004A

iii
Contents
Introduction
ProCurve Radio Port 230 and 210 Package Contents . . . . . . . . . . . . 1-1
Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-2
Technical Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-2
Dimensions & Weight . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-2
Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-3
Radio Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-4
Integrated RJ-45 Port . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-4
LEDs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-5
Radio Port 230 LEDs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-5
Startup: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-5
Normal Operation: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-6
Radio Error Mode: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-6
Radio Port 210 LEDs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-6
Startup Radio: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-6
Normal Operation: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-6
Radio Error Mode: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-6
Installation Instructions
Safety Wire Tie Point . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-2
Wall Mount . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-3
Wall Mount Hardware . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-3
Wall Mount Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-4
Safety Wire Tie Point . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-5
RJ45 Wiring Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-6
Suspended Ceiling Tile T-Bar Mount . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-7
Ceiling Mount Hardware . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-7
Ceiling Mount Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-7
To Install the Radio Port on the T-Bar: . . . . . . . . . . . . . . . . . . . . . . 2-7
To Remove the Radio Port from the T-Bar: . . . . . . . . . . . . . . . . . . 2-8

iv
Troubleshooting Radio Port Installation
Startup Error Checklist . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-2
HP Customer Service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-3
Before Calling Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-4
Safety and Regulatory Statements
Safety Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-1
Regulatory Statements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-2
Notice for U.S.A. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-2
Notice for European Community . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-3
Operation Using 5 GHz Channels in the
European Community . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-5
EU Declaration of Conformity . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-6
Notice For Japan . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-7
Notice For Taiwan . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-8
Recycle Statements
Waste Electrical and Electronic Equipment (WEEE)
Statements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-1

Introduction
1-1
1
Introduction
The ProCurve Radio Port 230 and ProCurve Radio Port 210, components of
the ProCurve Wireless LAN System, link wireless IEEE 802.11a/b/g devices to
the Ethernet network through a wireless services-enabled switch. Wireless
services-enabled switches include:
■ProCurve Switch 5300xl Series with a ProCurve Wireless Edge Services
xl Module
■ProCurve zl switches (such as 5400zl or 8200zl series) with a ProCurve
Wireless Edge Services zl Module
■Other compatible wireless services-enabled switch products.
The radio ports are designed as simple plug-and-play devices that require no
individual device configuration before network installation. All Radio port
configurations, including: country-specific settings, radio channels, radio
power, SSID settings, security settings, management information, and radio
port software is provided through the wireless services-enabled switch.
NOTE Before installing radio ports, a ProCurve wireless services-enabled switch
should be deployed, configured and operational. For details, see the Getting
Started Guide for your Wireless Edge Services Module.
ProCurve Radio Port 230 and 210
Package Contents
■ProCurve Radio Port 230 or Radio Port 210
■Two wall mount screws
■Two wall anchors
■Installation and Getting Started Guide
■Software License, Warranty and Support booklet

1-2
Introduction
Description
Introduction
Description
The ProCurve Radio Port 230 is a dual-radio IEEE 802.11-compliant device
supporting simultaneous IEEE 802.11a and b/g wireless Ethernet connections.
It contains two embedded IEEE 802.11 b/g (2.4 GHz) omni directional diversity
antennas, and two embedded IEEE 802.11a (5.4 GHz) omni directional diver-
sity antennas.
The ProCurve Radio Port 210 is a single radio IEEE 802.11-compliant device
supporting IEEE 802.11 b/g wireless Ethernet connections. It contains two
embedded IEEE 802.11 b/g (2.4 GHz) omni directional diversity antennas.
Both radio ports are designed for installation in office environments, either
using the wall mount or suspended-ceiling T-Bar mountings built into the
underside of the plastic case. Each radio port has one RJ-45 connector
supporting 10/100Base-TX Ethernet and requires power from any UL-listed,
IEEE 802.3af-compatible Power over Ethernet (PoE) switch or power
injector.
Technical Specifications
Dimensions & Weight
Operating Voltage 48VDC (from IEEE 802.3af-
compliant power source)
Operating Current 148mA (typical)
Power 7W (typical)
Operating Temperature 0 to 40° C (32 to 104° F)
Non-Operating/Storage
Temperature -40 to 70°C (-40°F to 158°F)
Operating Humidity 5 to 95% (non-condensing)
Non-Operating/Storage
Humidity 5 to 95% (non-condensing)
Operating Altitude (max) 3,048m (10,000ft.)
Non-Operating/Storage
Altitude 4,572m (15,000ft.)
Length 249.2mm (9.81in.)
Width 174.9mm (6.88in.)
Height 42.4mm (1.67in.)
Radio Port 230
Weight 0.55kg (1.214lbs)
Radio Port 210
Weight 0.50kg (1.096lbs)

1-3
Introduction
Features
Introduction
Features
■High-performance IEEE 802.11-compliant radios
■Embedded omni directional diversity antennas
■Integrated 10/100Base-TX RJ-45 port
■Two LEDs
■Safety wire tie point
■Lap-style lock port
■Slots for wall mounting
■Clips for mounting on a suspended ceiling T-Bar
LEDs
Wall Mount Slot
T-Bar Suspension Clips
Cable Recess
T-Bar Retaining Clip

1-4
Introduction
Radio Characteristics
Introduction
Radio Characteristics
The ProCurve Radio Port 230 comprises two IEEE 802.11 radios: (1) an IEEE
802.11 b/g radio operating in the 2.41 to 2.8 GHz band and (2) an IEEE 802.11a
radio operating in the 5.15 to 5.88 GHz band. The ProCurve Radio Port 210 has
a single IEEE 802.11b/g radio. Both units contain two embedded 2.41-2.8 GHz
omni-directional diversity antennas and the Radio Port 230 also contains two
embedded 5.1-5.88 GHz omni-directional diversity antennas.
The following table lists the IEEE 802.11-compliant operating modes. The
three supported IEEE 802.11g modes are simultaneous CCK and OFDM, CCK
only, or OFDM only.
For details on Transmit Power and Receiver Sensitivity values, reference the
Product Data Sheets located on the ProCurve Web site, www.procurve.com.
Integrated RJ-45 Port
Each radio port has one RJ-45 connector supporting a full-duplex 10/100Base-
TX Ethernet port, and requires IEEE 802.3af-compliant Power over Ethernet
(PoE) from an external source, such as a PoE switch or power injector. This
Ethernet port is configured as an MDI port and can be connected to any MDIX
switch port using standard straight-through CAT-5 Ethernet cables. For details
on cable pinouts, see the Installation and Getting Started Guide for your
ProCurve switch.
A single CAT-5 cable is used to supply both Ethernet connectivity and power
to the radio port allowing these radio ports to be installed up to 100 m (300
ft.) from a PoE-compliant 10/100Base-TX Ethernet port. There is no additional
power supply required.
Device Mbps Data Rate Support Utilizing
Diversity GHz
802.11a 6, 9, 12, 18, 24, 36, 48, 54
OFDM Transmit and receive 5.1 to 5.88 range
802.11b/g 1, 2, 5.5, 11 CCK
6, 9, 12, 18, 24, 36, 48, 54
OFDM
Transmit and
receive 2.41 to 2.8 range

1-5
Introduction
LEDs
Introduction
LEDs
Each radio port has LEDs on the front of the case that display the device status.
The LEDs display connection status and error conditions, as well as network
activity for the individual radios in the radio port.
Radio Port 230 LEDs
The Radio Port 230 has two LEDs displaying connection status, error
conditions, and networking activity for each of the two radios. Operation
is as follows:
Startup:
Radio Port Startup occurs immediately following the application of PoE
power, or following a power or software reset.
1. Both GREEN and AMBER LEDs light steadily for several seconds, while
the radio port performs an internal self-test.
2. The AMBER LED then flashes 3 times per second, while the GREEN LED
is off. This indicates that the radio port is attempting to communicate to
a compatible wireless services-enabled switch.
3. Both LEDs then go off for a moment, followed by both LEDs lighting
steadily for a few seconds.
4. After this sequence, assuming no error conditions have occurred, the
radio port enters Normal operation mode. This indicates the radio port
has successfully communicated with and been adopted by a wireless
services-enabled switch. If this startup sequence repeats itself, it is likely
the radio port is unable to contact a compatible wireless services-enabled
switch, and the installer should review the Troubleshooting section.
LEDs

1-6
Introduction
LEDs
Introduction
Normal Operation:
Once the radio port establishes a connection to a compatible wireless
services-enabled switch, the radio port begins normal operation. During
normal operation, the GREEN LED indicates the status of the IEEE 802.11
b/g radio, and the AMBER LED indicates status of the IEEE 802.11a radio.
• Without Wireless Traffic: Each LED briefly flashes once every 5
seconds, this indicates that power is on and the radio port is commu-
nicating normally to its wireless services-enabled switch. The flashing
may not be synchronous between the two LEDs.
• With Wireless Traffic: Each LED briefly flashes more frequently than
once every 5 seconds, and in an irregular fashion, to represent wire-
less traffic on that radio.
Radio Error Mode:
• The GREEN LED flashes on and off steadily once per second if an
error prevents the IEEE 802.11b/g radio from operating normally.
• The AMBER LED flashes on and off steadily once per second if an
error prevents the IEEE 802.11a radio from operating normally.
Radio Port 210 LEDs
The Radio Port 210 has two LEDs displaying connection status, error
conditions, and networking activity for its IEEE 802.11 b/g radio. Opera-
tion is as follows:
Startup Radio:
• Operation of the indicators is identical to the Radio Port 230 during
Startup.
Normal Operation:
• During Normal Operation, the GREEN LED flashes to indicate
connection and traffic on the IEEE 802.11b/g radio, similar to the
Radio Port 230. The AMBER LED remains off.
Radio Error Mode:
• The GREEN LED flashes on and off steadily once per second if an
error prevents the IEEE 802.11b/g radio from operating normally.

2
Installation Instructions
2-1
Installation Instructions
The ProCurve Radio Port 230 and 210 can be mounted either on a wall or on
a suspended ceiling T-bar. The radio ports are not designed for mounting on
a desk. The diagrams on the next page note the key installation features.
To prepare for installation, perform the following steps:
1. Match the model number on the purchase order with the model numbers
in the packing list and on the case of the shipped device.
2. Verify that the contents of the box include the intended ProCurve Radio
Port 230 or 210 and mounting hardware:
3. Review site survey and network analysis reports to determine the location
and mounting positions for the ProCurve Radio Port 230 and 210.
4. Connect a CAT-5 cable to a compatible IEEE 802.3af power source and
run the cable to the installation site. Ensure that there is sufficient slack
on the cable to perform the installation steps.
Radio Port Item Notes
230 J9006A 802.11a & 802.11b/g integrated antenna
configuration.
210 J9004A 802.11b/g integrated antenna configuration.
Wall Mount Slot
T-Bar Suspension Clips
See Detail Below
T-Bar Retaining Clip

2-2
Installation Instructions
Installation Instructions
Safety Wire Tie Point
RJ-45 Port
Lock Port

2-3
Installation Instructions
Wall Mount
Installation Instructions
Wall Mount
Wall mounting consists of hanging the ProCurve Radio Port 230 or 210 along
its width or length using the pair of wide-shoulder screws provided and
mounting slots on the underside of the radio port.
The ProCurve Radio Port 230 or 210 can be mounted onto any wood, plaster,
or cement wall surface using the provided wall anchors when necessary. The
illustration shows the radio port mounted horizontally.
Wall Mount Hardware
■Two wide-shoulder Phillips pan head self-tapping screws, or
• ANSI Standard) #6-18 X 0.875in, Type A or AB Self-Tapping Screw, or
• ANSI Standard Metric M3.5 X 0.6 X 20mm Type D Self-Tapping Screw.
■Two wall anchors.
■Safety wire-recommend between 1.0 mm (.04in.) and 1.6 mm (.06in.)and
security cable (optional)

2-4
Installation Instructions
Wall Mount
Installation Instructions
Wall Mount Procedure
1. Lightly mark a vertical line on the wall at the location where the midline
of the radio port is to be located.
2. Use the alignment arrows, move the edge of the radio port to the midline
from step 1 and mark the two points on the midline for the location of the
mounting screws. (See following diagram)
3. At each of the two points, drill a hole in the wall, insert an anchor (if
required), screw the wall mounting screw into the anchor and stop when
there is 2 mm remaining between the screw head and the wall.
NOTE When pre-drilling holes, the recommended hole size is 3mm (0.125 or 1/8 in.)
if the screws are going directly into the wall and 6mm (0.25 or 1/4 in.) if the
provided wall anchors are being used.
4. Loop a safety wire through the tie point and secure the loop. Attach the
opposite end of the safety wire to a secure point on the wall.
5. Install a security cable to the radio port's lock port and attach the opposite
end of the security cable to a secure, stationary point.
U
se
th
ese a
li
gnmen
t
arrows
t
o mar
k
th
e wa
ll
i
n prepara
ti
on
f
or
i
ns
t
a
lli
ng moun
ti
ng screws

2-5
Installation Instructions
Wall Mount
Installation Instructions
6. Plug the Ethernet cable to the RJ-45 port and connect the opposite end of
the cable to a switch with an IEEE 802.3af compatible power source. The
Ethernet cable can be tucked inside the cable recess on the underside of
the radio port case for a completely clean installation. (See following
diagram)
7. Place the middle of each of the case's mounting slots over the mounting
screw heads.
8. Slide the case down along the mounting surface to hang the mounting
slots on the mounting screws.
9. Verify the radio port has power by observing that the LEDs are lit or
flashing.
Safety Wire Tie Point
RJ-45 Port
Lock Port
Cable
recess

2-6
Installation Instructions
Wall Mount
Installation Instructions
RJ45 Wiring Options
The RJ-45 cable may be routed in multiple ways.
Cable exits
Cable exits
RJ-45 cable connection (tucked in recess and routed through wall
or tile)
Cable recess

2-7
Installation Instructions
Suspended Ceiling Tile T-Bar Mount
Installation Instructions
Suspended Ceiling Tile T-Bar Mount
Mounting the Radio Port 230 or 210 to a suspended ceiling T-Bar grid consists
of attaching the radio port to the underside of a T-Bar in a suspended ceiling
grid, and twisting the radio port to lock the case onto the T-Bar.
Ceiling Mount Hardware
■Safety wire-recommend between 1.01mm (.04in.) and 1.58mm (.06in) and
security cable (optional)
Ceiling Mount Procedure
To Install the Radio Port on the T-Bar:
1. Lift the ceiling tiles around the T-Bar where the radio port is to be installed.
2. Loop a safety wire around the tie point, secure the loop and attach the
opposite end to a secure point on the ceiling or T-bar grid.
3. Install a security cable to the radio port's lock port and secure the opposite
end to a secure, stationary point on the ceiling.
4. Plug the Ethernet cable into the RJ-45 jack and connect the opposite end
to a switch with an IEEE 802.3af-compatible power source. Thread the
cable through the ceiling T-Bar grid on the proposed radio port installation
side.
5. Position the radio port so the back of the radio port faces the bottom of
the T-Bar. Position the radio port case so that the T-Bar fits into the channel
formed into the underside of the radio port case.
6. Slide the radio port until the T-Bar Suspension Clip on the opposite side
of the radio port case slips over the T-Bar. Rotate the radio port counter-
clockwise slightly (approximately 15 degrees) to lock the remaining T-Bar
Suspension Clip into place. The T-Bar Retaining Clip clicks into place as
the Suspension Clips fasten onto the T-Bar. (See following diagram)

2-8
Installation Instructions
Suspended Ceiling Tile T-Bar Mount
Installation Instructions
7. Verify the radio port has power by observing the LEDs.
8. Tuck the Ethernet cable into the cable recess on the underside of the radio
port.
9. Replace the ceiling tiles around the T-Bar to complete the installation.
To Remove the Radio Port from the T-Bar:
1. Lift the ceiling tiles away from the T-Bar to which the radio port is
attached.
2. Using your finger, depress the T-Bar Retaining Clip that locks the radio
port to the T-Bar.
3. Rotate the radio port clockwise to release the T-Bar from the radio port’s
T-Bar Suspension Clips.
To install, turn radio
port counter-clockwise
Ceiling View: Install into T-Bar Suspension Clip (slide the radio port into the sus-
pension clip, then rotate radio port clockwise and the T-Bar Suspension click
locks))
T-Bar Retaining Clip
T-Bar Suspension Clip
T-Bar Suspension Clip (first secure)

3
3-1
Troubleshooting Radio Port
Installation
Troubleshooting Radio Port Installation
This section describes how to troubleshoot the installation of your ProCurve
radio port primarily from a hardware perspective. You can perform more in-
depth troubleshooting of your wireless LAN system from the console or Web
UI on your wireless services-enabled ProCurve switch.
For more information on software configuration or troubleshooting, see the
Getting Started Guide for your ProCurve Wireless Edge Services Module for
details.
Basic troubleshooting relies on the LEDs to diagnose the condition of the radio
port. The table below shows LED patterns on the radio port that indicate
problem conditions.
LED Error Indicators
GREEN LED AMBER LED Diagnostic Tips
Off steadily while Ethernet cable is
linked to a PoE source. Remains off
even when the radio port is
disconnected from Ethernet cable and
reconnected.
Off steadily while Ethernet cable is
linked to a PoE source. Remains off
even when radio port is disconnected
from Ethernet cable and reconnected.
Radio port is not receiving PoE power. Verify that the Ethernet
cable is connected directly to an IEEE 802.3af-compatible PoE
source, and that all cable connections are tight and secure.
Verify that the PoE source device is powered on, and that the
PoE function has been administratively enabled on the source
port connected to the radio port. Verify that the network cable
is functioning properly, or try a different cable. Try plugging
the radio port into another PoE power source, or connect
another PoE device to the port to confirm if the PoE source is
functioning appropriately.
Both GREEN and AMBER LEDs light steadily for several seconds, followed by the
AMBER LED flashing steadily on and off three times a second for several seconds,
then this cycle repeats itself continuously.
The radio port is encountering a Startup Error, and is unable to
successfully communicate with or be adopted by a compatible
wireless services-enabled switch. See the Startup Error
checklist below for further diagnostic tips.
Flashes on and off steadily once per
second * The radio port has encountered an error that prevents the IEEE 802.11b/g radio from operating normally.
* Flashes on and off steadily once per
second
(Radio Port 230 only) The radio port has encountered an error
that prevents the IEEE 802.11a radio from operating normally.
*This LED is not important for this diagnosis

3-2
Troubleshooting Radio Port Installation
Startup Error Checklist
Troubleshooting Radio Port
Installation
Startup Error Checklist
Startup errors occur when the radio port is unable to communicate with a
compatible wireless services-enabled switch, or when the radio port success-
fully communicates to a compatible switch but the switch is not able to adopt
and manage the radio port. The following steps can be used to determine the
different circumstances that may be preventing the radio port from being
adopted by the switch and operating normally.
1. The network connection between the radio port and the wireless services-
enabled switch has been disrupted. Verify that network connectivity
between the Ethernet cable and the wireless services-enabled switch by
connecting another device, such as a laptop, to the Ethernet cable and
confirming network connectivity to the switch. Verify the Ethernet port
to which the radio port is connected has not been disabled, and if IEEE
802.1X port security is turned on, that the IEEE 802.1X Port security is
compatible with the radio port's IEEE 802.1X settings. The network
between the radio port and the wireless services-enabled switch has a
Layer 3 compatibility issue (e.g. the two devices are on different subnets.)
2. The downlink VLAN has not been properly configured on all switch ports
between the Radio Port and the wireless enabled switch. (add a pointer
to the proper manual for more information on configuring the downlink
VLAN).
3. The wireless services-enabled switch may not be configured properly.
Verify the Wireless Edge Services Module is properly installed, configured,
and operational. In particular, verify that the wireless services' country-
code setting has been properly configured, as this setting must be config-
ured to enable the wireless service to function. Refer to the Getting
Started Guide for your ProCurve Wireless Edge Services Module for
details.
4. The wireless services-enabled switch may not be functioning normally.
Refer to the Getting Started Guide for your ProCurve Wireless Edge
Services Module for details on verifying operation.
5. The Wireless Edge Services Module may have adopted radio ports up to
it's Authorization Level and may not be authorized to adopt additional
radio ports. Review the number of radio ports the wireless services-
enabled switch has currently adopted and compare this number to the
number of radio ports authorized based on the licenses installed.