HRS DF63 Series User manual

1. Scope
This document specifies the steps to insert or remove the DF63 series.
It contains general guidelines and precautions for the safe use of the product. The use of the
product in a way not as specified in the document could result in unexpected troubles such as
damage to connectors. Please make sure to thoroughly read and understand the document
prior to the use of the product.
2. Connectors
Part No.
Description
DF63%-*S-3.96C(##)
Socket
DF63%-*P-3.96DS(A)(##)
Header
DF63%-*EP-3.96C(##)
In-line Plug
DF63%-****SC(F)(A)
DF63%-****PC(F)(A)
Crimp contact
COUNT
DESCRIPTION OF REVISIONS
DESIGNED
CHECKED
DATE
0
名称TITLE
DF63 Series Mating / Unmating Operation Instruction Manual
APPROVED
HS.OKAWA
20190514
CHECKED
SZ.ONO
20190514
DESIGNED
TO.KUROMATSU
20190514
WRITTEN
TO.KUROMATSU
20190514
TECHNICAL SPECIFICATION
ETAD-H0892-00
0
1/ 6
FORM HC0011-9-1
HIROSE ELECTRIC CO.,LTD.
△
△
（E.g.）DF63-3S-3.96C
+DF63-1618SCF(Cables attached)
（E.g.）DF63M-3P-3.96DSA
DF63M-3P-3.96DS
DF63-3EP-3.96C
DF63A-3EP-3.96C
Fig1.DF63 connector
May.1.2020Copyright2020HIROSEELECTRICCO.,LTD.AllRightsReserved.

HIROSE ELECTRIC CO.,LTD.
ETAD-H0892-00
0
2 /6
FORM HC0011-9-2
△
3. Operation procedure
3-1. Insertion
3-1-a. Positioning for insertion:
：Adjust the position for insertion according to the locks of the socket or In-line plug.
3-1-b. Insertion:
Insert the socket till it clicks while retaining the adjusted position.
Then, it is not needed to handle the lock portion
(If it is inserted the socket by pushing the lock portion, it does not hear click sound.)
Fig.3 Insertion
Direction of insertion
Fig2. Positioning for insertion
Center
position
Lock
portion
May.1.2020Copyright2020HIROSEELECTRICCO.,LTD.AllRightsReserved.

HIROSE ELECTRIC CO.,LTD.
ETAD-H0892-00
0
3 /6
FORM HC0011-9-2
△
To avoid degraded quality, do not tilt the socket for insertion as shown in the
figure below.
3-1-c. Check fitting:
Make sure the socket has been firmly fit with the header or In-line plug.
(Check that the socket lock has been caught at the header lock or In-line plug lock
by slightly pulling a cable by hand.)
To remove the socket, refer to 3-2. Socket removal.
Fig.4 Prohibited insertion
May.1.2020Copyright2020HIROSEELECTRICCO.,LTD.AllRightsReserved.

HIROSE ELECTRIC CO.,LTD.
ETAD-H0892-00
0
4 /6
FORM HC0011-9-2
△
3-2. Socket removal
3-2-a. Removal:
：Remove the socket while pressing with a finger the lock spring on the socket to unlock.
To avoid degraded quality, do not tilt the socket for removal as shown
in the figure below.
Fig.5 Socket removal
Direction of removal
Lock spring
Fig6. Forbidden removal
May.1.2020Copyright2020HIROSEELECTRICCO.,LTD.AllRightsReserved.

HIROSE ELECTRIC CO.,LTD.
ETAD-H0892-00
0
5 /6
FORM HC0011-9-2
△
Attention）Not to remove socket in the locked status as it will lead to breakage
of locking portion or cable broken.
If remove socket in the locked status, the lock is engaged to header lock portion
as below picture shown. Then, it can not handle the lock. In this case,
please insert the socket once. After that, handle the lock portion.
Fig7. How to handle to avoid unable unlock status
Insert direction
Unable unlock
Able unlock
Caught in lock portion
May.1.2020Copyright2020HIROSEELECTRICCO.,LTD.AllRightsReserved.

HIROSE ELECTRIC CO.,LTD.
ETAD-H0892-00
0
6 /6
FORM HC0011-9-2
△
4. Precautions
・Do not insert or remove the socket while electrifying.
・Excessive external force applied to connectors could cause fault or damage.
Therefore, avoid forced insertion or removal, impacts given by falling,
or forced pulling of cables.
・Avoid insert socket by bundling the cable
or applying stress to the socket like below picture shown.
Fig8. Forbidden insertion
May.1.2020Copyright2020HIROSEELECTRICCO.,LTD.AllRightsReserved.