Huck AEROBOLT FAR 10U05 User manual

Page 1of 5
FAR® GUN –10U05
Far® brand air gun for Huck bolts & Huck structural rivet diameters 4.8, 6.4 & 7.9mm* (3/16’, 1/4' & 5/16’)
The HG-10U05 is a light-weight production tool designed for the installation of Huck bolts and rivets. The
tool accepts a wide range of nose assemblies which can be quickly and easily changed covering diameters
sizes: 4.8mm (3/16"), 6.4mm (1/4") *plus 7.9mm (5/16") structural rivets, steel & aluminium only.
* Nose assemblies sold separately.
Far Gun HG-10U05 comes with: Nosepiece adapter, wrench, air fitting,
oil bottle, mandrel deflector and manual.
Specification
Weight
2.6Kg
Air Pressure
6 Bars (90-100 psi)
Stroke
19.5mm
Pulling Force
22.725Kn @ 6 bar (90-100psi)
Fastener Capacity*
Huck bolts & Huck rivets 4.8mm (3/16”)
& 6.4mm (1/4”) plus 7.9mm (5/16”)
structural rivets in steel & aluminium only

Page 2of 5
Warranty
FAR tools are covered by a 12-month warranty. The tool warranty period starts on the date of delivery to the
buyer, as specified in the relevant document. The warranty covers the user/buyer provided that the tool is
purchased through authorized dealer and only if it is used for the purposes for which it was conceived. The
warranty shall not be valid if the tool is not used or maintained as specified in the instruction and
maintenance handbook. In the event of defect failures, FAR s.r.l. shall undertake solely to repair and/or
replace the component it judges to be faulty.
Safety Measures and Requirements
WARNING! All the operations must be done conformity with the safety requirements, in order to avoid
any consequence for your and other people’s security and to allow the best tool work way.
•Read the instructions carefully before using the tool.
•For all maintenance and/or repairs please contact FAR s.r.l. authourized service centers and use only
original spare parts. FAR s.r.l. may not be held liable for damages from defective parts caused by
failure to observe what above mentioned (EEC directive 85/374)
•The device must be used only by expert workers.
•A protective visor and gloves must be put on when using the device.
•For topping up the oil, we suggest using only fluids in accordance with the features specified in this
working book.
•If any drop of oil touches your skin, you must wash with water and alkaline soap.
•The voice needs a thorough six-monthly overhaul.
•Repairing and cleaning operations must be done when the device is not fed.
•If it is possible, we suggest a safety balancer.
•If the A-weighted emission sound pressure level is more than 70dB (A), you must use some hearing
protections (anti-noise headset, etc.).
•The workbench and the work surface must be always clean and tidy. The untidy can cause damages
to people.
•Do not allow unauthorized persons to use the working device.
•Make sure that the compressed air feeding hoses have the correct size to be used.
•Do not carry the connected device by pulling the hose.
•Keep the device in good conditions; do not remove either safety parts or silencers.
•Before disconnecting the compressed air hose from the device make sure
that there is no pressure in the hose.
•These instructions must be carefully followed.
WARNING! Before using the device, assemble the protection bottom supplied
with the tool, as indicated in the picture on the side. FAR has no responsibility
for any damages on the device, persons or things caused by lack of protection
bottom.

Page 3of 5
Air Feed
The air feed must be free from foreign bodies and humidity in order to protect the device prom premature
wear and tear of the components in movement; therefore, we suggest using a lubricator group for
compressed air.
Topping Up the Oil-Dynamic Circuit
You need to top us the hydraulic circuit after a long period of work, when you note a power loss. Put the
riveting device (DWELL AND NOT FED) in a horizontal position and remove the plug (A), by means of a 5
mm Allen wrench (equipped with the riveting device); during this operation, check the oil level in order to
avoid overflowing. Then, slowly pour the oil PANOLIN HLP ISO 32 into the bellows container (X) which shall
be screwed into its seat on the plug (A). While keeping the riveting device in a horizontal position and
starting air feeding; push the tensile strength button and make the riveting device carry out some cycles
until air bubbles inside the container (X) stop coming out. This condition indicates that the topping up of the
oil has fully been achieved. At this point, while keeping the riveting device in a horizontal position, unscrew
the oil container (X) and close it again. Do not push the tensile strength button during this operation. Go
on by closing the oil tank plug (A).
WARNING! It is very important to follow the above-mentioned instructions and use gloves. If the
hydraulic circuit should be fully emptied, collect the oil in a suitable container and contact an authorized
company r its disposal.
WARNING!
•Before disconnecting the compressed air hose, make sure that it is not under pressure!
•Make sure that the oil filler cap (A) is tightened at torque corresponding to
Min. 5 Nm –Max. 8Nm.
•We recommend using oil PANOLIN HLP ISO 32 DIN 51524-2HLP or similar.
Device Disposal
For the device disposal, comply with the national laws. After disconnecting the device from energy sources, start the
disassembly of the components according to their material: sheet, aluminium, plastic and so on.
Go on with the scrapping in accordance with the national standards.

Page 4of 5
HG-10U05: Exploded View

Page 5of 5
HG-10U05: Parts List