IBASE Technology SI-08 Series User manual

SI-08 Series
User Manual

Revision
Release Date
V0.1
2012/07/03
V0.2
2014/08/13

3
Copyright © 2011 IBASE Technology INC. All Rights Reserved.
No part of this manual, including the products and software described in it, may be
reproduced, transmitted, transcribed, stored in a retrieval system, or translated into
any language in any form or by anymeans, except documentation kept by the
purchaser for backup purposes, without the express written permission of IBASE
Technology INC. (“IBASE”).
Products and corporate names mentioned in this manual may or may not be
registered trademarks or copyrights of their respective companies, and are used for
identification purposes only. All trademarks are the property of their respective
owners.
Every effort has been made to ensure that the contents of this manual are correct and
up to date. However, themanufacturer makes no guarantee regarding the accuracy of
its contents, and reserves the right to make changes without prior notice.

4
Table of Contents
Safety Information ................................................................................................. 5
Acknowledgments.................................................................................................. 7
Accessories............................................................................................................. 8
Components ........................................................................................................... 9
I/O View...............................................................................................................................9
Specification..........................................................................................................10
Mounting SI-08 to the Wall....................................................................................11
Wall mounting requirements.............................................................................................11
Selecting the location ........................................................................................................12
SI-08 mounting bracket solution……………………………………….………………………………...13
Exploded view of the SI-08 assembly .....................................................................14
Parts description................................................................................................................14
Installation............................................................................................................15
Installing the memory........................................................................................................15
Setting Jumper...................................................................................................................16
Pin Definition.....................................................................................................................17
BIOS Setup ............................................................................................................18
BIOS Introduction ..............................................................................................................18
BIOS Setup .........................................................................................................................18
Main BIOS Setup ................................................................................................................19
Advanced Settings..............................................................................................................21
Chipset Settings .................................................................................................................32
Boot Settings......................................................................................................................38
Security Settings ................................................................................................................39
Save & Exit Settings ...........................................................................................................40
Driver Installation .................................................................................................42

5
Safety Information
Your SI-08 is designed and tested to meet the latest standards of safety for
information technology equipment. However, to ensure your safety, it is important that
you read the following safety instructions.
Setting up your system
Read and follow all instructions in the documentation before you operate your
system.
Do not use this product near water.
Set up the system on a stable surface. Do not secure the system on any unstable
plane.
Do not place this product on an unstable cart, stand, or table. The product may
fall, causing serious damage to the product.
Slots and openings on the chassis are for ventilation. Do not block or cover these
openings. Make sure you leave plenty of space around the system for ventilation.
Never insert objects of any kind into the ventilation openings.
This system should be operated from the type ofpower indicated on themarking
label. If you are not sure of the type of power available, consult your dealer or
local power company.
Use this product in environments with ambient temperatures between 0˚C and
45˚C.
If you use an extension cord, make sure that the total ampere rating of the
devices plugged into the extension cord does not exceed its ampere rating.
DO NOT LEAVE THIS EQUIPMENT IN AN ENVIRONMENTWHERE
THESTORAGE TEMPERATURE MAY GO BELOW -20°C (-4°F) OR ABOVE
80°C (176°F). THIS COULD DAMAGE THE EQUIPMENT. THE EQUIPMENT
SHOULD BE IN A CONTROLLED ENVIRONMENT.
Care during use
Do not walk on the power cord or allow anything to rest on it.
Do not spill water or any other liquids on your system.
When the system is turned off, a small amount of electrical current still flows.
Always unplug all power, and network cables from the power outlets before
cleaning the system.
If you encounter the following technical problems with the product, unplug the
power cord and contact a qualified service technician or your retailer.

6
The power cord or plug is damaged.
Liquid has been spilled into the system.
The system does not function properly even if you follow the operating
instructions.
The system was dropped or the cabinet is damaged.
Lithium-Ion Battery Warning
CAUTION: Danger of explosion if battery is incorrectly replaced. Replace only with
the same or equivalent type recommended by themanufacturer. Dispose of used
batteries according to the manufacturer’s instructions.
NO DISASSEMBLY
The warranty does not apply to the products that have been disassembled by users
WARNING
HAZARDOUS MOVING PARTS
KEEP FINGERS AND OTHER BODY PARTS AWAY

7
Acknowledgments
AMI is a registered trademark ofAMI Software International, Inc.
AMD and ATI are registered trademarks ofAMD Corporation.
Microsoft Windows is a registered trademark of Microsoft Corporation.
FINTEK is a registered trademark of FINTEK Electronics Corporation.
REALTEK is a registered trademark of REALTEK Electronics Corporation.
All other product names or trademarks are properties of their respective owners.

8
Accessories
a. Power Cord x 1
b. Driver CD x 1
c. Power Brick x 1

9
Components
I/O View
Refer to the diagram below to identify the components on this side of the system.
DVI
The Digital Visual Interface (DVI) port supports a high quality VGA-compatible
device such as amonitor or projector to allow viewing on a larger external
display.
LAN
The eight-pin RJ-45 LAN port supports a standard Ethernet cable for connection
to a local network.
COM
Communication or serial port is compatible with RS-232 interface without RI (ring
indicator) signal.
USB
The USB (Universal Serial Bus) port is compatible with USB devices such as
keyboards, mouse devices, cameras, and hard disk drives. USB allows many
devices to run simultaneously on a single computer, with some peripheral acting
as additional plug-in sites or hubs.
AUDIO
The stereo audio jack (3.5mm) is used to connect the system’s audio out signal to
amplified speakers or headphones.

10
DC-IN
The supplied power adapter convertsAC power to DC power for use with this
jack. Power supplied through this jack supplies power to the system. To prevent
damage to the system, always use the supplied power adapter.
Specification
System Mainboard
EB-900
Construction
SGCC 1.0t
Chassis Color
Black / White
Storage
2.5” 160GB SATA HDD x 1
Mounting
Wall mount
Dimensions
200(W) x 34.8(H) x 150(D)mm
Power Supply
60W DC adapter
Operating Temperature
0°C ~ 45°C (32°F ~ 113°F)
Storage Temperature
-20°C ~ 80°C
Relative Humidity
5~90% @45°C (non-condensing)
Vibration
HDD: 0.25 Grms/5~500Hz random operation
Shock
HDD: 15 Grms peak acceleration (11 msec duration)
RoHS
Available
‧ This specification is subject to change without prior notice.