IBM 3745 Series User manual

3745 Communication Controller All Models
3746 Nways Multiprotocol Controller Model 900
Console Setup Guide
--..- -
----
-- ---
---
- -. ---
--- ---
-----
-----, -
SA33-0158-09

o
o
o
o
o
3745 Communication ControllerAll Models
3746 Nways Multiprotocol Controller Model 900
Console Setup Guide
----
----
-- ---
---
-- ---
- -- ---
-----
---,-
SA33-0158-09

Note! ----~~------------------------------------~---------------------------------,
Before Llsing this information and the product it supports, be sure to read the general information under "Notices"
on page xi.
Tenth Edition (June 1998)
The information contained in this manual is subject to change from time to time. Any such changes will be reported in later revisions.
Order publications through your IBM* representative or the IBM branch office serving your locality. Publications are not stocked at
the address given below.
A form for readers' comments appears at the back of this publication. If the form has been removed, address your comments to:
IBM France
Centre d'Etudes et Recherches
Service 0798 -BP 79
06610 La Gaude
France
• FAX: [phone]
• IBM Internal Use: LGERCF at IBMFR
• Internet: [email protected]
When you send information to IBM, you grant IBM a non-exclusive right to use or distribute the information in any way it believes
appropriate without incurring any obligation to you.
© Copyright International Business Machines Corporation 1989, 1998. All rights reserved.
Note to U.S. Government Users -Documentation related to restricted rights -Use, duplication or disclosure is subject to
restrictions set forth in GSA ADP Schedule Contract with IBM Corp.
/
..

o Contents
o
o
c
"
o
Figures
Tab res
Notices ..... .
European Union (EU) Statement
Electronic Emission Notices
...
Trademarks and Service Marks
Safety
........ .
About this Guide
Conventions Used in this Guide
Who Should Use this Guide .
How this Guide is Organized
What is New in this Edition
Where to Find More Information
World Wide Web ...... .
Part 1. 3745 Models A and 3746 Model 900
Chapter 1. Introduction to Remote Consoles and DCAF
Consoles ........................... .
Diskettes with Example Configurations
........ .
DCAF Logon Password and Service Processor Security
Regaining Control of the Service Processor
..... .
Minimum Workstation (Remote Console) Configuration
Programming Requirements
........... .
Hardware Requirements and Recommendations
Chapter 2. DCAF Session Installation
Summary of Procedures ..
Preparation . . . . . . . . . . . . .
Physical Insta"ation
...... .
Installing DCAF
Upgrading DCAF
.... .
Installing TCP/IP ..... .
Customizing CS/2 and CM/2
Customizing a Remote Workstation
Loading Example Configurations
..... .
Starting CS/2 and CM/2 Configuration
Configuring Data Link Control (DLC) for a Service Processor
Chapter 3. Using DCAF to Remotely Log On to·the Service Processor
Starting a Session ........... .
Closing a Session
........... .
From the Remote Workstation
From the Target Service Processor
ix
ix
xi
xi
xi
xiii
xiii
xv
xv
xvi
xvi
xvii
xvii
xvii
1-1
1-2
1-3
1-3
1-4
1-4
1-4
1-5
2-1
2-1
2-1
2-2
2-2
2-3
2-3
2-3
2-3
2-4
2-4
2-4
3-1
3-1
3-2
3-2
3-2
Chapter 4. TCPIIP LAN-Attached Remote Workstation Configuration 4-1
© Copyright IBM Corp. 1989, 1998 iii

Configuring a Target Service Processor ......... .
Configuring a TCP/IP LAN-Attached Remote Workstation
Configuring DCAF for TCPIIP
Configuring TCP/IP ................... .
4-1
4-4
4-4
4-6
Chapter 5. APPC LAN-Attached Remote Workstation
Configuration 5-1
Configuring a Target Service Processor . . . . . . . 5-1
Parameter Values that Must Be the Same ....... 5-2
Configuring the Service Processor
in MOSS-E 5-2
Configuring a APPC LAN-Attached Remote Workstation 5-5
Configuring
CS/2 ....... 5-5
Configuring DCAF for APPC
............... 5-11
Chapter 6. Modem-Attached Remote Workstation Configuration 6-1
Configuring a Target Service Processor . . . . . . 6-1
Parameter Values that Must Be the Same ...... 6-2
Configuring the Service Processor
in MOSS-E 6-2
Configuring Workstation Modems
........ 6-4
Configuring
CS/2 and CM/2 in Workstations 6-6
Configuring Workstation for
an IBM Modem ... 6-6
Procedures for Service Processors 9577 and 9585 6-7
Procedures for Service Processor 3172
....... 6-8
Procedures for Service Processor 7585
....... 6-9
Modem 7855
in Synchronous Mode to Service Processor 9577,9585,
and 3172 via MPA Card
in Synchronous Mode (17855SYN) ..... 6-10
Modem 7855 in Asynchronous Mode to Service Processor 9577, 9585,
3172, and 7585 via Serial Port
(17855ASY) ............... 6-15
Modem 7857
in Synchronous Mode to Service Processor 9577, 9585,
and 3172 via MPA Card
in Synchronous Mode (17857SYN) ..... 6-20
Modem 7857 in Asynchronous Mode to Service Processor 9577, 9585,
3172, and 7585 via Serial Port
(17857 ASY) ................. 6-25
Modem 7857
in AutoSync Mode to Service Processor 9577,9585, and
3172 via MPA Card
in Sync Mode (17857AUT) .. . . . . . . . . . . .. 6-30
Hayes Modem in Asynchronous Mode to Service Processor 9577, 9585,
3172, and 7585 via Serial Port (HAYESASY)
.............. 6-35
Hayes Modem
in AutoSync Mode to Service Processor 9577,9585, and
3172 via MPA Card in Sync Mode (HAYESAUT) 6-40
Configuring DCAF for a Modem .......... 6-45
Chapter 7. SNA-Attached Remote Workstation
Configuring a Target Service Processor ........ .
Parameter Values that Must
Be the Same .... .
Configuring the Service Processor
in MOSS-E
Configuring a SNA-Attached Remote Workstation ..
Configuring CS/2 ................... .
Configuring DCAF for SNA . . .
NCP Definitions
........... .
Remote Controlling Workstation
..
Target Service Processor
VTAM Definitions .
Start Definitions
Logmode Table
Major Node Definitions
Remote Workstation
iv All 3745 Models & the 3746-900: eSG
7-1
7-1
7-2
7-2
7-5
7-5
7-10
7-12
7-12
7-13
7-14
7-14
7-14
7-15
7-15
\,,- ... _/
()

o
o
o
o
o
Target Service Processor ........... .
Chapter 8. APPN-Attached Remote Workstation
Configuring a Target Service Processor ..... .
Parameter Values that Must
Be the Same ... .
Configuring the Service Processor in MOSS-E
Configuring an APPN-Attached Remote Workstation
Configuring CS/2
...... .
Configuring DCAF for APPN ........... .
Chapter 9. Telnet-attached Remote Workstation
Introduction
Consoles ............ .
Logon Password
........ .
Programming Requirements
..
Hardware Requirements and Recommendations
Installation ....................... .
Using Telnet to Remotely Log
On to the Network Node Processor
Starting a Session
Closing a Session .......................... .
Part 2. 3745 Models 130 to 610
Chapter 10. Setting Up a Local or an Alternate Console
General Information on Local or Alternate consoles
3151 in Native Mode (Local or Alternate) .....
3151 in 3101 Emulation Mode (Local or Alternate)
3153
in 3151 Emulation Mode (Local or Alternate)
Recommended Settings
.....
Starting the Console Configuration
Leaving the Console Configuration
3161 or 3163 (Local or Alternate)
IBM PS/2 (Local or Alternate) .....
MOSS Local or Alternate Console Emulation with CM/2 and Softerm
3727
............................. .
Testing a Connection with the Local or Alternate Console
Chapter 11. Setting Up a Remote Console
General Information (Remote) ..... .
3151 in Native Mode (Remote) .... .
3151 in 3101 Emulation Mode (Remote)
3153
in 3151 Emulation Mode (Remote)
Recommended Settings
.....
Starting the Console Configuration
Closing the Console Configuration
3161 or 3163 (Remote)
IBM PC ................ .
IBM PS/2 (Remote) ......... .
MOSS Remote Console Emulatioh with CM/2 and Softerm
Starting Custom Plus
........... .
Defining a New Session
......... .
Defining the Terminal Emulation Profile
Defining Connection Path Profile
....
7-15
8-1
8-1
8-2
8-2
8-4
8-4
8-10
9-1
9-1
9-1
9-2
9-2
9-2
9-2
9-2
9-2
9-2
10-1
10-1
10-2
10-3
10-5
10-5
10-5
10-6
10-6
10-6
10-9
10-9
10-10
11-1
11-1
11-2
11-3
11-5
11-5
11-5
11-6
11-6
11-6
11-7
11-10
11-10
11-10
11-10
11-12
Contents V

Ending Definition of a New Session ............ .
Other Types of Consoles .................... .
Testing the Modem·Connection to
a· Remote Console
Chapter 12. Modem·Setup ...... .
Modems for 3745· Models 130 to 160
Setting Up
........................ .
Switch Settings for
IBM Modems 5841, 5842, and 5853 "
IBM 5841 Modem ..................... .
IBM 5842 Modem ..................... .
IBM 5853 Modem ..................... .
Modems for 3745 Models A
...
Setting the IBM 7855 Modem .................... .
Setting the
IBM 7857 Modem Connected to MPA Card (SYN)
Setting the 7857 Modem Connected to COM1 (ASYN) ....... .
Setting the 7857 Modem Connected to MPA Card
on COM2 (ASYN)
Setting the
IBM 7858 Modem Connected to MPA Card (SYN)
Setting the 7858 Modem Connected to COM1 (ASYN)
....... .
Setting the 7858 Modem Connected
to MPA Card on COM2 (ASYN)
Chapter 13. RSF Modems
IBM 5858 Modem ...... .
IBM 7855 Modem ...... .
IBM 7857 Modem ...... .
Part 3. Appendixes for 3745 Model A and 3746 Model 900
Appendix A. Configuration for a Two-Target Remote Workstation
NCP Definitions .......... .................... .
VTAM Definitions
........ .
Start List
........... .
Logmode Table
........ . ........... .
Switched Major Nodes
.... .
DCAF Remote Workstation Configuration
...... .
Appendix B. Configuring DLC for DCAF .....
Create or Change the Token-Ring Network DLC Adapter Profile
Create or Change the SOLC DLC Adapter Profile
......... .
Part 4. Appendixes for 3745 Models 130 to 610
Appendix C. Location of 3745 Console Connectors
3745 Communication Controller Models 130, 150, 160, and 170
3745 Communication Controller Models. 210, 310, 410, and 610
11-12
11-13
11-13
12-1
12-1
12-1
12-2
12-2
12-2
12-2
12-3
12-3
12-4
12-5
12-5
12-6
12-6
12-6
13-1
13-1
13-1
13-1
A-1
A-2
A-2
A-2
A-3
A-3
A-4
B-1
B-1
B-1
C-1
C-1
C-1
Appendix D. Console and RSF Interface Cables ... . . . . 0-1
Cable from the 3745 to a Local Console
.................. 0-1
local Console Cable Assembly ....................... 0-1
Cable from the 3745 to an Alternate Console .................. 0-2
Alternate Console Cable Assembly ..................... 0-2
Cable Adapters for Local!Alternate Consoie ................... 0-2
Console Connection through the IBM 7427 Console Switching Unit ..... 0-3
vi All 3745 Models &the 3746-900: eSG
,/
o

o
c
o
o
Cable from the 3745 to the 7427 Switching Unit (A)
Cable Assembly for Local Console ....... .
Cable Assembly for Alternate Console ..... .
Cable from the 7427 to a 31xx, PS/2, or PC Console (8)
Cable Assembly for 31 xx Console ....
Cable Assembly for PS/2 or PC Console .. .
Cable from the 7427 to a 3727 Console (B) .. .
Cable Assembly ........... .
Remote Console Cable
.......... .
Cable to Modem for Remote Console
Cable to Modem for RSF
RSF Modem Cable
......... .
Part 5. Bibliography, Abbreviations, Glossary, and Index
0-3
0-3
0-3
0-3
0-3
0-3
0-3
0-3
0-4
0-4
0-4
0-4
Bibliography ..................................... X-1
Customer Documentation for the IBM 3745 (Models 210,310,410,610, 21A,
31A, 41A, and 61A), and 3746 (Model 900)
.... . . . . . . . . . . . . . .. X-1
Additional Customer Documentation for the IBM 3745 Models 130, 150, 160,
170, and 17A
..... . . . .. ..... X-5
List of Abbreviations .
X-1
Glossary X-3
Index .. X-7
Contents vi i

viii All 3745 Models &the 3746-900: CSG

o Figures
c
Tables
o
o
o
1-1.
4-1.
5-1.
5-2.
5-3.
6-1.
6-2.
6-3.
7-1.
7-2.
7-3.
8-1.
8-2.
9-1.
A-1.
DCAF Console Attachments
Types of TCP/IP Service LAN-Attached Remote Workstations
APPC Service LAN-Attached Remote Workstation
NetView Link/Reporting Customization
DCAF Customization
........ .
Modem-Attached Remote Workstation
NetView Link/Reporting Customization
DCAF Customization
........ .
SNA-Attached Remote Workstation
NetView Link/Reporting Customization
DCAF Customization
APPN Remote Workstation ...
DCAF Customization
Telnet Workstation Configuration
A Two-Target Configuration
2-1. DCAF Session Installation Procedures
5-1. Identical Target and Controlling Parameters
6-1. Identical Target and Controlling Parameters
6-2. Recommended IBM Modems, their Settings, and CS/2 (or CM/2)
Configurations
.......................... .
6-3. IBM Modems for Remote Workstations and Target Service
Processors 9577 and 9585
................... .
6-4. IBM Modems for Remote Workstations and a Target Service
1-2
4-1
5-1
5-3
5-4
6-1
6-3
6-4
7-1
7-3
7-4
8-1
8-3
9-1
A-1
2-1
5-2
6-2
6-5
6-7
Processor 3172 .......................... 6-8
6-5. IBM Modems for Remote Workstations and a Target Service
Processor 7585
............... . 6-9
7-1. Identical Target and Controlling Parameters
.......... 7-2
8-1. Identical Target and Controlling Parameters
.......... 8-2
X-1. Customer Documentation for the 3745 Models x10 and x1A, and
3746 Model 900
............................ X-1
X-2. Additional Customer Documentation for the 3745 Models 1 xO and
17A
.................................... X-5
© Copyright IBM Corp. 1989, 1998 ix