iCandy peach User manual
iCandy
Read these
instructions carefully before
use and keep for future
reference. Your child’s safety
may be affected if you do not follow
these instructions.
Peach Inst AUS Print V4.indd 1 21/07/2011 20:24
iCandy
iCandy
Please take time to read this instruction booklet carefully as
correct use and maintenance of your iCandy stroller is essential.
If you have any problems or queries, please contact your local
stockist or read the FAQ’s at
When unpacking your stroller, please make sure that all plastic
packaging is kept away from babies and young children and
please ensure your child is kept clear of all moving parts during
assembly.
Peach Inst AUS Print V4.indd 2 21/07/2011 20:24
iCandy
iCandy
iCandy
Peach Inst AUS Print V4.indd 3 21/07/2011 20:24
iCandy
Contents
Section 1 – Chassis
Section 2 – Seat Unit
Section 3 – Bassinettes
Section 4 – Peach “Blossom”
Section 5 – Peach “Blossom Twin”
Section 6 – Single Stroller Car Seat Adaptors
Section 7 – Blossom Stroller Car Seat Adaptors
Section 8 – iCandy Peach Congurations
Section 9 – Accessories
Section 10 – General Use & iCare
Section 11 – Important Safety Information
Safety First
Correct use and maintenance of your stroller is essential. Please
take the time to fully and carefully read this instruction manual.
If you require any further advice or assistance when using your
stroller, please contact the place of purchase.
With the exception of the outer packaging carton, to
prevent injury from choking or suffocation hazards, remove and
immediately discard all other protective packaging on this product.
The iCandy Peach is tested to comply with AS/NZS 2088:2000,
AS/NZS 2088:2009. Consumer Protection Notice Nº. 8 of 2007.
Useful tip
New products are sometimes stiff to engage and operate. We
recommend ALL adaptors (sold separately) and connector parts
be lightly lubricated with a silicone based furniture polish. This is
best achieved by spraying polish onto a soft cloth and applying to
relevant parts.
iCandy
Peach Inst AUS Print V4.indd 4 21/07/2011 20:24
iCandy
Section 1 – Chassis
Contents:
Chassis inc. front wheels & basket
Rear Wheel x 2, Axles x 2
Seat Unit, canopy, bumper bar
PVC Raincover
Depress axle button to engage as
shown. Check security of wheels
by pulling outwards.
Release
the hold together clip (store clip
in-line with handle chassis).
Allow front frame of chassis to
move forwards.
Lift up handle until locks
engage.
Ensure that all the
locking devices are engaged
before use
1
2
4
3
iCandy
Peach Inst AUS Print V4.indd 5 21/07/2011 20:24
iCandy
Press down on
pedal to engage. Lift up to
release.
Can be
selected in xed or swivel
position. (Swivel position
required for folding chassis).
Adjust handle height to desired
position (x4) by depressing
button and pulling up.
(Remove seat/
bassinette before folding):
Unload all products from the
basket.
Apply brakes. Depress
handle button and slide handle
fully down in a swift/smooth
action to disengage hub locks.
6
7
5
iCandy
8
Peach Inst AUS Print V4.indd 6 21/07/2011 20:24
iCandy
iCandy
As the hub locks release;
move/rotate handle down.
Pull up basket frame at
centre using carry strap or hinge
joint, allowing the front frame and
wheels to move inwards.
Secure folded chassis using
hold together clip (Please note:
the chassis will only fully close &
stand upright if the front wheels
are selected to swivel & the
handle is at its lowest height).
The folded chassis can be carried
using the carry strap. (Check
security of strap clips, before
lifting).
The iCandy
Peach is tted with a tether strap
which should always remain
tted to the chassis and should
be positioned to either side of the
handle height adjustment button.
Should you need to remove &
ret the strap for example after
cleaning, simply pass the larger
looped end through the small
loop and pull to secure.
12
9
10
11
Peach Inst AUS Print V4.indd 7 21/07/2011 20:24
iCandy
iCandy
2
1
3
Section 2 – Seat Unit
The seat frame
movement mechanism is
supplied in the store/transport
position.
Depress and
hold both the outer frame
release ring and the centre
recline button simultaneously
before rotating leg to centre
position as shown.
Action on both sides of frame
before tting to the chassis.
Failure to do this
will lead to damage to your
seat unit.
Removing the hood requires
the use of the hood removal/
operation key.
Depress both locking tabs
and allow connectors to lift out
of sockets.
Peach Inst AUS Print V4.indd 8 21/07/2011 20:24
iCandy
iCandy
Insert the hood removal /
operation key into the zip puller.
Rotate the key into an upright
position.
Pull upwards to disengage the
zip fully and around the seat.
Engage
the end of the zip into the foot of
the zip. Insert the hood removal/
operation key into the zip puller.
Rotate the key into an upright
position and pull upwards and
around the seat to t the zip fully.
Remove key.
Always engage
the zip so it is fully closed and
remove key.
4
5
6
7
8
Peach Inst AUS Print V4.indd 9 21/07/2011 20:24
iCandy
iCandy
For Australian market the
shape of the bumper bar will
differ slightly. Operation and
tting is not affected.
Attach the
Bumper Bar with the inclined
angle towards the foot end of
seat unit. Ensure both locking
tabs fully engage. Check security
by pulling bar upwards.
Depress both locking tabs rmly
inwards and lift from sockets.
Insert
the seat unit into the main
connectors on the chassis. Push
down on each side of the seat
frame to engage.
Check that both locking tabs
are ush with the chassis hub
slots before use. The Seat Unit
can be positioned to face you or
face forwards.
Check that the
bassinette or seat unit
attachment devices are correctly
engaged before use.
9
10
11
12
Peach Inst AUS Print V4.indd 10 21/07/2011 20:24
iCandy
iCandy
Depress the centre grey buttons
simultaneously and rotate seat
to desired position (3 recline
positions in single mode).
(Remove child before). Depress
the lower portion of the grey outer
ring on each side of the seat and
lift the seat unit upwards.
Depress both hinge
buttons and move footrest to desired
position. Release button to lock.
13
14
15
Peach Inst AUS Print V4.indd 11 21/07/2011 20:24
iCandy
iCandy
Push
the left and right connectors
into the buckle housing & click
together. Adjust the length of the
straps using slider buckles “a”.
:
Squeeze in and pull out of the
buckle housing.
Fabric loops are provided for
attaching an extra harness
complying to BS 6684/EN13210.
: To avoid serious
injury, always use the 5-point
safety harness.
Shoulder straps are height
adjustable.
The shoulder straps can be
removed from the seat fabric
by feeding through the back/
baseboards.
Raincovers
Fit
raincover over the hood/
canopy area before tting over
the footrest part of the frame.
Ensure elasticated seams of
raincover are positioned over
frame of Seat Unit.
Never leave
raincovers, hoods and aprons
on or over the stroller indoors,
in a hot atmosphere or near a
heat source, your child may
overheat.
A harness which
can form loops may cause a
strangulation hazard. When the
seat is not in use the harness
straps should always be
disconnected.
Peach Inst AUS Print V4.indd 12 21/07/2011 20:24
iCandy
iCandy
Section 3 – Bassinettes
(all bassinettes)
The bassinette
attachment mechanism is
supplied in the store/transport
position.
Depress and
hold both the outer frame
release ring and the centre
recline button simultaneously
before rotating leg to centre
position as shown.
Action on both sides of the
frame before tting to the
chassis. 1
Peach Inst AUS Print V4.indd 13 21/07/2011 20:24
iCandy
iCandy
Remove
apron and mattress.
Position and secure both
‘stay’ bars into baseboard clips.
Replace mattress and apron as
necessary.
Clip hood
frame into sockets ensuring both
locking tabs are fully engaged.
Attach rear section of hood fabric
using zip. Pull up the hood frame
hoop to desired position.
To release hood, separate zip and
depress both locking tabs before
removing from sockets.
Attach
the handle into the sockets with
the inclined angle towards
the of the bassinette.
2
3
4
Peach Inst AUS Print V4.indd 14 21/07/2011 20:24
iCandy
iCandy
Ensure both locking tabs
fully engage. Check security by
pulling handle upwards.
Depress
both locking tabs rmly inwards
and remove from sockets.
rearward facing
onlyOrientate the bassinette
so that it is facing rearwards and
insert the arms into the left &
right receptors of the main hubs
on the chassis.
Push down rmly on each side of
the bassinettes frame to engage.
Check that the hub locking tabs
are ush with the chassis hub
slots before use.
5
6
7
Peach Inst AUS Print V4.indd 15 21/07/2011 20:24
iCandy
iCandy
Depress the lower
portion of the grey outer ring on
each side of the bassinette and lift.
Do not lift bassinette
using hood frame.
Bassinette Raincovers
Fit raincover over the hood/canopy area
before tting over the foot end of bassinette. Ensure elasticated
seams of raincover are positioned under the base of the bassinette.
Bassinette Information (Main)
(Guide only for main bassinette mattress size)
iCare
Bassinette liners and aprons are washable at 30 degrees.
Bassinette frames are sponge clean only.
8
Peach Inst AUS Print V4.indd 16 21/07/2011 20:24
iCandy
iCandy
Section 4 – Peach
“Blossom”
Contents
As main pushchair
(See Section 1).
Blossom converter frames (b).
Main/upper seat stop screws
(not shown).
Lower seat unit (c).
PVC rain cover (not shown).
See section 1 of these
instructions.
a
b
c
Peach Inst AUS Print V4.indd 17 21/07/2011 20:24
iCandy
iCandy
Blossom Converter
Insert the
top sections of each converter
frame into the chassis hub
connectors.
Align the “saddles” on the
lower parts of the frame with the
basket frame.
Push down rmly on the top and
bottom sections of the converter
frames to engage
Ensure locking tabs are ush
with chassis hub slots and the
“Saddles” on the lower part of
the frames are clamped around
the basket frame.
Push across grey latching levers
and disengage lower saddles
before lifting the converter frame
out of the chassis hubs.
Remove
converter frames before
attempting to fold the chassis
2
3
4
5
Peach Inst AUS Print V4.indd 18 21/07/2011 20:24
iCandy
iCandy
Lower seat unit
The seat frame
movement mechanism is
supplied in the transport/storage
position.
Depress and hold
both the outer frame release ring
and the central release button
simultaneously before rotating
the leg to the central position
Action on both sides of the seat
before tting to chassis.
Failure to do this will
result in damage to your seat.
Insert seat arms into lower
“Blossom” converter frame
sockets and push down rmly to
engage.
Frame legs are grooved
to prevent incorrect orientation
(forward facing only).
Depress the central grey buttons
simultaneously and rotate into
the desired position.
Remove the child. Depress
the lower portion of the grey
outer rings of the seat unit, the
frame will “Jump up”. The rings
can be depressed simultaneously
or independently.
6
7
8
9
Peach Inst AUS Print V4.indd 19 21/07/2011 20:24
iCandy
iCandy
Upper/Main seat unit
Assembly & operation is the same
as the single stroller (see Section
2).
Ensure that the seat
frame movement mechanism is
taken out of the store/transport
position prior to tting (see page
8).
Fit the screws
supplied to the upper/main seat
unit movement mechanism this
is essential to restrict upper seat
recline movement to prevent
interference with lower seat.
Insert seat arms into upper
“Blossom” converter frame
sockets and push down rmly to
engage.
Depress the central grey buttons
and rotate into the desired
position.
Recline is restricted to
2 position to prevent interference
between upper and lower seats.
Remove child
rst. Depress lower portion of
the grey outer ring on each side
of seat unit, the frame will “Jump
up”. The rings can be depressed
simultaneously or independently.
10
11
12
13
Peach Inst AUS Print V4.indd 20 21/07/2011 20:24
Other manuals for peach
2
Other iCandy Stroller manuals
iCandy
iCandy peach User manual
iCandy
iCandy PEACH JOGGER User manual
iCandy
iCandy RASPBERRY User manual
iCandy
iCandy PEACH7 User manual
iCandy
iCandy LIME User manual
iCandy
iCandy PEACH ALL TERRAIN User manual
iCandy
iCandy Strawberry User manual
iCandy
iCandy peach User manual
iCandy
iCandy ORANGE User manual
iCandy
iCandy strawberry 2 User manual
