IKUSI 4328 User manual

Installation guide
FLOW-STB-4K IP HDMI
Set-Top Box
(4328)

Regulatory information
UK
This equipment has been tested and found to comply with
the essential requirements of the following Regulations:
The Radio Equipment Regulations 2017, The Electrical
Equipment (Safety) Regulations 2016, Electromagnetic
Compatibility Regulations 2016. This product is in
accordance with The Waste Electrical and Electronic
Equipment Regulations 2013. Hereby, Telecommunication
Technology LLC declares that FLOW-STB-4K IP HDMI with
the radio equipment type 802.11a/b/g/n/ac is in compliance
with the Radio Equipment Regulations 2017. The full text of
the declaration of conformity is available at the following
internet address:
www.Ikusi.eu/eng/support/declarations
This device is certified for indoor deployment only in the
5150-5350 MHz band. Do not install or use this device
outdoors in that frequency in the UK.
EU
This equipment has been tested and found to comply with
the essential requirements of the following Directives:
2014/30/EU, 2014/35/EU, 2014/53/EU, 2009/125/EC,
2011/65/EU. This product is in accordance with Directive
WEEE 2012/19/EU.
Hereby, Telecommunication Technology LLC declares that
FLOW-STB-4K IP HDMI with the radio equipment type
802.11a/b/g/n/ac is in compliance with the 2014/53/EU
Directive. The full text of the EU declaration of conformity is
available at the following internet address: www.Ikusi.eu/
eng/support/declarations
This device is certified for indoor deployment only in the
5150–5350MHz band. Do not install or use this device
outdoors in that frequency in the European Union.
FCC
This equipment has been tested and found to comply with
the limits for a Class B digital device, pursuant to Part 15
of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference when
the equipment is operated in a residential installation. This
equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with
the instruction manual, may cause harmful interference
to radio communications. However, there is no guarantee
that interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the
equipment o and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
•Reorient or relocate the receiving antenna.
•Increase the separation between the equipment and
receiver.
•Connect the equipment to an outlet on a circuit dierent
from that to which the receiver is connected.
•Consult the dealer or an experienced radio/TV technician
for help.
FCC Caution:
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:

Warranty term:
Europe, MEASA and Oceania:
2years from date of sale (but not more than 2,5years from
manufacture date).
The USA, Americas, Russia, Ukraine and other regions:
1year from date of sale (but not more than 1,5years from
manufacture date).
See the date of manufacture at «Product Information»
section. By virtue of the present Coupon, the absence
ofdefects in manufacturing of the product and its
compounds is warranted for a year-term counted since date
of sale. Ifduring the mentioned warranty term the defects of
materials or operation of product will be found, the product
would be repaired or its defective parts would be replaced
free of charge in the warranty processing center with
compliance with warranty conditions.
Warranty
1) this device may not cause harmful interference, and
2) this device must accept any interference received,
including interference that may cause undesired operation.
CAUTION:
Unauthorized antennas, modifications, or attachments could
damage the device and violate FCC regulations. Changes or
modifications not expressly approved by responsible party
could void the user’s authority to operate the equipment.
FCC Radiation Exposure Compliance
(FLOW-STB-4K IP HDMI):
This equipment complies with radio frequency (RF)
exposure limits set forth by the Federal Communications
Commission for an uncontrolled environment. This
equipment should be installed and operated with a
minimum distance of 20 centimeters between the radiator
and your body. This transmitter must not be co-located
or operating in conjunction with any other antenna or
transmitter.
This device is certified for indoor deployment only in the
5150–5250MHz band. Do not install or use this device
outdoors in that frequency in the United States.

Warranty processing centers
Europe:
ZLS Services GmbH
Hamburger Allee 56
60486, Frankfurt am Main, Germany
Tel.: [phone]
e-mail: [e-mail]
The USA, Canada and Latin America:
Infomir USA
174 Bay 49th Street
Brooklyn, NY 11214 USA
Tel: [phone]
e-mail: [email protected]
Russia, Belarus:
Tel.: [phone]
e-mail: [e-mail]
MEASA and Oceania:
PROGRESSIVE TECHNOLOGY F.Z.E
Warehouse B1-40
Sheikh Rashid Bin Saeed Al Maktoum Street
Ajman Free Zone, 45573, Ajman, UAE
Tel: [phone]
e-mail: [e-mail]
Ukraine:
Telecommunication Technologies LLC
4/D, Nebesnoi Sotni Avenue
Odesa, 65121, Ukraine
Tel: [phone]
e-mail: [e-mail]
Warranty
Warranty Service Coupon
(to be filled in by a shop-assistant)
Date of Sale:
Seller:
Address of Seller:
Place of Stamp
I have no claims as to appearance and
package contents. I accept the warranty
conditions.
Signature of Customer:
Manufacturer:
Telecommunication Technologies LLC,
1 Mytna Square, Odesa, 65026, Ukraine

Warranty conditions
1. The present warranty is only valid if the defective product
is provided with properly filled in Warranty Service
Coupon. If date of sale is not pointed, the warranty term
is counted since date of the product manufacturing which
is defined under serial number. Warranty processing
center reserves the right to refuse free warranty
service and parts replacement in case the mentioned
above documents are not presented or the filled in it
information is not complete or unreadable.
2. The present warranty does not enable the right for
compensation and cover of loss received as a result of
rearrangement of the product.
3. The present warranty is invalid if model or serial number
of the product is altered, erased, removed or unreadable,
or warranty seal is broken.
4. The present warranty does not cover the following:
4.1. Any adaptations and alterations with the aim of
perfection and widening of the common scope of the
product application specified in the Manual.
4.2. Devices and accessories not specified in the “Product
Information” section.
4.3. The batteries for the remote control included with the
Set-Top Box.
4.4. Damage caused in result of:
a) Improper maintenance including but not limited by following:
(1) use of the product not according to its intended purpose or
Manual;
(2) mounting and maintenance of the product in conditions not
corresponding to safety standards and regulations valid in
the country of use;
(3) incorrect software installation provided by service operator.
b) Repair performed by not authorized service centers or dealers;
c) Accidents, lightning stroke, flood, fire, incorrect ventilation;
d) Transporting excluding cases when it is carried out by warranty
processing centers;
e) Faults of system in which the present product had been using.
5. These warranty conditions do not intend to restrict or
limit in any way statutory rights of customers which may
not be altered in some jurisdictions and other customers’
rights which may arise out of any agreements with
third parties, provided that nothing contained in such
agreements states or implies that the manufacturer
or manufacturer aliates assume any obligations or
liabilities other than those expressly stipulated in this
Warranty Service Coupon.
While maintaining warranty liabilities on product repair
or replacement, Manufacturer takes no responsibilities
for personal data safety, including logins, passwords,
paid or free subscriptions, settings, portals, media files,
content and software installed or set up by Customer or
other third parties.

Copyrights and Trademarks
Notice of Copyright
Telecommunication Technologies LLC. All rights reserved.
The Information contained herein is the property of
Telecommunication TechnologiesLLC (the Company).
Not any part hereof can be copied, reprinted, transferred,
retyped, saved in search engine, modified or translated
into any other language, including computer one, nor
sublicensed in any way, whether electronic, mechanical,
magnetic, optical, chemical, manual or other one,
without prior written consent by the Company Manager
responsible for the Product. Any Illegal use of the materials
contained herein, by any person, will lead the person to the
responsibility for the Company’s damages.
Software Use Agreement
IMPORTANT: READ CAREFULLY: WHEN USING THE SOFTWARE WITH
YOUR DEVICE, YOU AGREE THEREBY WITH EVERY CLAUSES OF THE
SOFTWARE USE AGREEMENT. IF YOU DO NOT AGREE WITH THE
TERMS AND CONDITIONS OF THE SOFTWARE USE AGREEMENT, YOU
SHOULD IMMEDIATELY STOP USING THE DEVICE AND RETURN IT TO
YOUR SERVICES PROVIDER COMPLETELY.
License provision. Limitations
According to this Agreement, Telecommunication
Technologies LLC and your services provider are jointly
to provide you with non-exclusive and non- transferrable
license, without the right to sublicense, for use of all
software and documents with the product only. You
recognize and acknowledge that Telecommunication
Technologies LLC and your services’ provider may regularly
renew, change or extend the product software abilities. You
confirm that:
a) You will not take attempts to change, extend, or
decompile, disassembly, or redesign, nor otherwise get
access to the software source code.
b) You will not take attempts to delete or upload the product
software. Any sale or transfer of the product will be ruled
hereby.
Ownership
The Manufacturer and the Manufacturer’s own licensors
keep all the rights constituting ownership, including patent,
copyright trademark, and other intellectual property for
the Software; and any improvement and modification of
the Software. You recognize and acknowledge that the
license according hereof does not grant you ownership for
the Software but only restricted right of use It according to
provisions of this Agreement.
Warranty for the Software
To the maximum extent according to applicable law, the
Company does not make any submission and declines
any and all warranties, whether express or implied, as to
the Software, including, with no limitations, any implied
demand warranties, correspondence to target destination,
abuse of rights of third parties, neither those being result
of interrelations or result of commerce. The Company does
not guarantee the Software will be free of defects or errors;
that any defects or errors will be corrected, or any function

Copyrights and Trademarks
abilities of the Software will meet all your requirements.
Trademarks
Ikusi, are the trademarks of Ikusi Group. The terms HDMI
and HDMI High-Definition Multimedia Interface, and the
HDMI Logo are trademarks or registered trademarks of
HDMI Licensing Administrator, Inc. in the United States
and other countries. Manufactured under license from
Dolby Laboratories. Dolby, Dolby Audio, and the double-D
symbol are trademarks of Dolby Laboratories. Linux® is the
registered trademark of Linus Torvalds in the U.S. and other
countries. Ikusi disclaims proprietary interest in the marks
and names of others.
Terms of using
Safe and Ecient Using
Device does not contain harmful or hazardous substances.
Accessories
Use the accessories supplied with your arrangement or
recommended by the manufacturer only. Using of the
accessories which are not supplied or not sanctioned by the
manufacturer may be dangerous for the User or do harm
to the arrangement operation. Using of the not appropriate
accessories eliminates guarantees of the product therewith.
Water and Moisture
To avoid damage that can cause ignition of the present
product or lesion to the User with electrical current, the
product and its accessories should not be undergone with
any liquids, rain or high moisture. Do not use the present
product in the places where it may be exposed to the
contact with aliquid or vapor.

The Product Unpacking and Installation
After the product extraction out of the package it is
necessary to handle it with care, do not drop, shake it
and aord other influence. The product is designed for
horizontal allocation onto flat surface. The product is
intended for use indoors.
•Do not place the product onto slippery surface, in place
where it may be exposed to vibration or hazard to drop
and other possible risks to the product to be damaged
which may cause invalidation the product warranty.
•Do not leave the product on soft surfaces such as rugs,
beds, etc. The absence of an air gap between the body of
the set-top box and the surface can lead to overheating
and void the warranty.
•Do not locate the product into the furniture in case of
vacant clearance around the product is not provided for
the sucient product ventilation.
•Do not place the product in place where it may be
exposed to influence of direct sunlight, next to the
sources of open fire and convectors.
•Do not dispose the product on surfaces which in operating
process may get warm, for instance, video record player
or intensifier and do not put anything on the top of the
shell as well.
•Do not cover the product with anything.
•Containing liquids objects, such as vase, plant pot are not
to be placed next to or on the product.
•Do not touch or move the product during its operation.
•Switch o the product if you need to shift it.
The power supply cord is to be put to prevent its
deformation and jamming and touching it well. The power
supply cord is not to be laid under the carpets or blocked
with anything where any damage may not be noticed.
Power supply unit
The product should be used with power supply unit provided
by the manufacturer only. The power supply unit is fitted
out with plug which is intended for connecting to socket in
your country usage. In case of the necessity in the product
connecting in other country or in the region with other
data of electric circuit the power supply unit adopted for
use in the specified area should be received from the
manufacturer. ForAC/DC Adapter, the socket outlet must be
near the equipment and shall be easily accessible.
Operation
The outer power supply unit of the product is getting warm
in operation. In case of outer power supply unit gets hot,
switch o promptly and get in touch with the equipment
supplier for its replacement.
Protection from atmospheric electricity or not using
for a long time
On coming the thunderstorm and also in case of the product
is intended to be in no use for a long time, disconnect the
power supply cord out of socket, switch o Ethernet, video
and audio cables. It is to protect the product from thunder
discharges and power surges in the circuit.
Usage with Plasma Displays
In the product usage for watching with plasma screens do

not pause the picture for more than 5 minutes, otherwise
it with other objects as may cause ‘burn-out’ pixels on the
screen. It is not considered as a defect of the product but
peculiarity of plasma screens structure. The producer does
not bear the responsibility for damages had been caused in
such manner.
The Arrangement Designation
The product is intended to select digital audio & video
channels from transport streams, decode and display
them on TV. Any other use is prohibited. It means
Telecommunication Technologies LLC insists on the product
usage in entirely accordant to the law of copyright. The
compliance with the specified laws leaves on conscience
of the user. The unauthorized copying of the protected
materials or spreading of the specified copies under definite
conditions may violate the law of copyright and is to be
previously adopted by possessor of the rights for the further
commercial use.
Updating Software
The product possesses the capability of automatic software
updating. The manufacturer and your services provider
reserve the right for automatic software updating to
improve the product functional capability. During the
software updating the product should not be used for
watching and switched o until the complete software
Product Care
updating. During the software updating the product
switching o is inadmissible. The updating takes several
minutes and since then you are able to continue enjoy on all
delights of digital television services.
Maintenance of Product
The product should not be disassembled. The tries of the
disassembling of the product may be dangerous for your
life and for serviceability of the product. The self-supporting
disassembling invalidates you the product guarantee. The
maintenance should be aected by qualified specialists
in the warranty processing centers only. The product
possesses protective sealing. Breaking or changing of the
mentioned sealing invalidates guarantee of the product.
Cleaning
The product and accessories should be rubbed with dry
cloth or tissue only. To ensure safety, before shell cleaning
switch the power supply o the alternative current socket.
The shell may be cleaned from persistent spots with a
slightly wet cloth or cleaning tissue. Do not use cleaner or
polish, benzyl, solvents, abrasive items, liquid or aerosol
detergent means for the product and accessories cleaning.

Specifications
Physical Parameters
Model: FLOW-STB-4K IP HDMI
Weight: 110 g (3,88 oz). Dimensions (approximately): 78 mm
(3.07’’) depth, 120 mm (4,72’’) width, 21 mm (0.83’’) height
Operation temperature and Humidity
1°C - 40°C (33,8 F - 104 F); 5% ~ 93%RH
Ethernet Interface
Ethernet Connector: RJ-45
Cable: UTP and STP 5 categories
Speed: Auto-choice, 10/100 Mbit/s
Indicators: Green – Activity, Yellow – Connection
Wi-Fi Interface
Built-in Wi-Fi module: 2T2R ac (FLOW-STB-4K IP HDMI)
Operating frequency bands:
802.11 b/g/n 2400 MHz ~ 2497 MHz,
802.11 a/n/ac 4900 MHz ~ 5845 MHz
Output power (E.I.R.P.):
IEEE 802.11 a/b/g/n/ac <20 dBm (100mW)
Internal Antenna gain (max): 3,11 dBi (5 GHz), 2,69 dBi (2.4
GHz)
HDMI Interface
Type: HDMI 2.1
USB Interface
Type: USB 2.0 x 1 pcs., USB 3.0 x 1 pcs.
Supported Audio-Video Formats
Video codecs: MPEG1/2 MP@HL, MPEG4 part 2 (ASP), H.265
Main/Main [email protected] High 2160p@60 fps (optional),
H.264 AVC [email protected] 2160p@30 fps, XviD, 3D video support
Video containers: TS, AVI, MPEG, MP4, MOV, MKV, M2TS, VOB
Audio Codecs: MPEG L1/L2/L3, AAC-LC, HE AAC V1/V2, APE,
FLAC
This product supports Dolby Digital Plus™
Video modes: PAL, NTSC, 576p, 720p, 1080p, 1080i, 4K
Subtitles: DVB, PGS, SRT, SSA/ASS, SUB, Teletext subs,
WebVtt, Closed captions
Power supply Interface
Connector: DC cylindrical 1.35 mm x 3.5 mm
Type: center plus
Input: 5 V
Power Consumption: max 5W in typical conditions
External Power Supply Unit
Type: Pulse with universal inlet
Input: 90–264 V AC, 50-60 Hz, 0.4 A max
Output: 5 V DC, 2 A, 10 W
Package
Type: cardboard box.
Dimensions (approx.): 225 mm (8.86 ‘’) width, 95 mm (3.74’’)
depth, 60 mm (2.36’’) height
Shipping weight: 432 g (15.24 oz)
NOTE: SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE.
IKUSI RESERVES THE RIGHT TO REVISE THIS PUBLICATION AND TO
MAKE CHANGES IN ITS CONTENT FROM TIME TO TIME BY POSTING
NEW SPECIFICATIONS AND OTHER CONTENT AT WWW.IKUSI.EU

Step 1
Connect HDMI Cable
Step 2
Connect Power Supply
Unit
Step 3
Connect to the Internet
(via Ethernet or Wi-Fi *)
Connecting to FLOW-STB-4K IP HDMI
WARNING! SWITCH OFF ALL THE DEVICES (TV, AMPLIFIER, ETC.)
AND TAKE THE POWER SUPPLY UNIT OUT OF THE SOCKET BEFORE
CONNECTING OR DISCONNECTING ANY CABLE.
* ONLY IN FLOW-STB-4K IP HDMI
About your FLOW-STB-4K IP HDMI
1. USB 2.0
2. USB 3.0
4. Fn – Reset to factory settings/ Load from the first U-boot/
“Emergency” – Load the basic software from USB/DHCP
1. Power Supply 5V 2. HDMI 2.1 3. Ethernet LAN
port
Front Panel
Back Panel

Using Remote Control to control the Device
Introduction to the Programmable Remote Control
Unit (optional)
If FLOW-STB-4K IP HDMI, package includes a remote control
with a block of five programmable buttons (marked with
blue print colour), then you may want to choose these
buttons for controlling other devices (TV set, amplifier).
To program the buttons do the following:
1. Press the “On/O” and “A/V” buttons at the
same time and hold it for 2 seconds. When the green light
of the “On/O” button will stop blinking and will light
steadily, it means the RC is ready to learn.
2. Press the button you want to «teach» — the green light
will start blinking.
3. Place the infrared lamps of two RCs opposite each other
and press the button on the RC of the other device, the
function of which you wish to copy on device RC. Hold for
2 seconds.
4. After the green light two quick blinks you may continue
programming other buttons.
5. Repeat the procedure described above for all buttons you
want to program for controlling external devices.
6. Press the the “On/O” and “A/V” buttons to save
the programmed data; the green light should fade o.
Reset
Press “SETUP” and “OK” buttons at same time and
hold for 2seconds red LED will flash 5 times. Reset is done.

Turn the Media Player On/Off
Change audio mode
Setup menu
TV Guide
Virtual keyboard
Back
Info
Switch channels
Rewind
Fast forward
Skip backwards
Skip forward
TV channel section
*BUTTONS ALLOWED TO STORE COPIED DATA
Programmable section*
Sound On/Off*
A/V*
Context menu
Quick TV access
Exit
Menu
Volume*
Play / Pause
Stop
Change aspect ratio
Update
Additional functions
Up
Down
Confirm
Right
Left
Programmable Remote Control SRC-4513

FLOW-STB-4K IP HDMI model

FLOW-STB-4K IP HDMI model

Product information
The set includes the following:
Set-Top Box
External Power Supply 5V
IR Remote Control
HDMI cable length less than 3 m
AAA batteries
Instruction manual
Package box
- 1 pcs.
- 1 pcs.
- 1 pcs.
- 1 pcs.
- 2 pcs.
- 1 pcs.
- 1 pcs.
Optionally the set may include the following:
LAN network cable - 1 pcs.
Donostia Ibilbidea, 28 · 20115 Astigarraga · Gipuzkoa · España Tel.: [phone]
[email protected] - www.ikusi.tv
Product:
Serial Number:
MAC: