IKUSI MHD-201 Operating instructions

SPI-300 EN
PROGRAMMING GUIDE
FOR
«MHD-201» MODULATOR
CVBS; HDMI; HD-SDI  DVB-T or IP
DVB-T OUT
HDMI
SDI
USB
LAN
V/A 1
SYNC STATUS
+12V
Link
Act
V/A 2
VIDEO
AUDIO
L
AUDIO
R
CONTROL
VIDEO
AUDIO
L
AUDIO
R
Ref. 3854
MHD-201
DIGITAL MODULATOR
DVB-T OUT
HDMI
SDI
USB
LAN
V/A 1
SYNC STATUS
+12V
Link
Act
V/A 2
VIDEO
AUDIO
L
AUDIO
R
CONTROL
VIDEO
AUDIO
L
AUDIO
R
Ref. 3854
MHD-201
DIGITAL MODULATOR
DVB-T OUT
HDMI
SDI
USB
LAN
V/A 1
SYNC STATUS
+12V
Link
Act
V/A 2
VIDEO
AUDIO
L
AUDIO
R
CONTROL
VIDEO
AUDIO
L
AUDIO
R
Ref. 3854
MHD-201
DIGITAL MODULATOR
1 2 3
4 5 6
7 8 9
C 0
SPI-300

2
Programming MHD-201 Modules
Contents
START SCREENS
1 - Module Basic Information ......................................................3
2 - Main Menus ........................................................................... 3
Overview Screen .................................................................... 4
Settings screen ........................................................................ 5
Info Screen ...............................................................................6
Language screen ......................................................................7
PROGRAMMING SCREEN
1 - General ................................................................................... 7
IP
Date-Time
2 - Settings ...................................................................................8
Input
Output:
3 - USB Player ............................................................................11
Status
Mode
QUICK MENUS ........................................................................... 12-13

3
Programming MHD-201 Modules
START SCREENS
1 - Module Basic Information
As described in Basic Handling guide supplied with the SPI-300, on connec-
ting it to the module the identication data, settings and status of the module
are loaded onto the remote. The module detection screen appears for a short
time, and then the display shows the Basic Information screen, which con-
tains its most representative data:
The meanings of expressions and data presented are:
Module name.
F 02.18: Version of the module rmware (the rmware is software stored in
the module that is responsible for its basic operation).
CH 21: By default the output channel is 21.
SYSTEM OK (status correct); NO IMPUT (no input signal is detected; SYSTEM
NOK (status incorrect).
Pressing the OK command (key ) takes us to the Main Menu Screen (Basic
Handling Manual).
2 - Main Menus
As indicated in the Basic Handling Manual, the General menu and Langua-
ge are identical for all ClassA modules and their commands are described in
it. Setting andInfoMenus include, however, options or information, unique to
each module type.
MDHD-201 F 02.18
CH 21 SYSTEM: OK
OK

4
Programming MHD-201 Modules
Main Screen GENERAL
The General menu is identical for all ClassA modules and the commands are
the following:
• Detect: Runs the detection process of the connected module.
• Send: Establishes on the module the parameter values that have been mo-
died.
• Update: This option does not apply to this model. The rmware update is
performed only through the web interface (see manual www.ikusi.tv).
• Recall: Returns the conguration of the module previously created with the
Save command. This menu is useful to quickly load repetitive data in multi-
ple modules.
1  General
2 Settings
3 Info
4 Language SEL
1  Detect
2 Send
3 Update
ESC  SEL
4 Recall
5 Save
6 Factory Reset
ESC   SEL
7 About ...
ESC  SEL
MDHD-201 F 02.18
CH 21
SYSTEM: OK
OK

5
Programming MHD-201 Modules
• Save: Saves the module conguration in the memory of the SPI-300 remote.
• Factory Reset: Restores all parameter values that were set up in the module
when it left the factory
• About ... : Simply reports the rmware version of the SPI-300.
Main Screen SETTINGS
The Settings menu contains all the setting parameters of the connected
module. Grouped by sections or categories that are arranged in one or more
screens:
• Input: Select one of the input types available on the module.
• Output: This menu quickly accesses the output channel (default channel 21)
and attenuation in COFDM mode.
• Country: Must be selected to have the specic congurations operating in
each country such as the ONID or LCN mode.
• Language: Enables one of the available languages to be selected.
• Advanced: Should be selected to carry out module conguration operations
(see detailed explanation later).
SPI-300
vXX.XX (DD/MM/YY)
Copyright 2009
IKUSI OK
1 General
2  Settings
3 Info
4 Language SEL
1  Input
2 Output
3 Country
ESC  SEL
4  Language
5 Advanced
ESC  SEL

6
Programming MHD-201 Modules
Main Screen INFO
The Info menu provides access to detailed information about the connected
module, regardless of whether it has been programmed or not.
• Status: Informs about the operating conditions of the module.
 CH1 VID: Reports the existence or not of a valid video signal.
 CH1 AUD: Reports the existence or not of a valid audio signal.
 Player: Reports the operation of the USB channel.
 % Free: The middle number expresses the percentage of null PIDs (no information) that are currently in the output
stream; the higher the number, the less risk there is of overflow (in other words, less risk of data loss). The numbers
on the left and the right are respectively the minimum and maximum values that have been reached over the period
of operation of the module, since the last power connection.
 Bitrate: Reports the data encoding speed on output.
 IP Bitrate: Reports the data encoding speed on output.
 Num Str: Reports the number of services.
• Alarm: Reports whether there is an alarm active on the module and what
type it is.
 HW: Displays error if a problem has been detected in the hardware.
 In: Displays error if an HD input is inserted in an SD input.
 Cod: Displays the status of MPEG encoder.
 Sl: Displays the status of the DVB signalling.
 Mod: Displays error if there is any problem with the DVB-T output.
 IP: Displays error if there is any problem with the IP output.
 Sync: Displays error if there is a problem of synchronisation.
• Details: Identies the module and displays relevant data about it.
 HW: Displays the hardware version of the module.
 SW: Displays the software version of the module.
 BS: Displays the Bootstrap version.
 SERIAL: Displays the serial identification number of each module.
 MAC: Displays the number that identifies each module for networking.
1 General
2 Settings
3  Info
4 Language SEL
1  Status
2 Alarm
3 Details
ESC SEL

7
Programming MHD-201 Modules
Main Screen LANGUAGE
Select here the language you want to operate in from now on. Position the
cursor in the "Spanish" line and press the button .
PROGRAMMING SCREEN
In the next part of this manual, the commands to congure the module will be
explained.
From SETTINGS on the Main screen move to the ADVANCED submenu which
shows the following parameters:
1 - GENERAL : Select this menu to access the following submenus:
IP:
Indicates the factory set IP address parameters .
1 General
2 Settings
3 Info
4  Language SEL
1  General
2 Settings
3 USB Player
ESC SEL
1  IP
2 Date-Time
ESC SEL
1 IP: 192.168.1.6
2 MR: 255.255.255.0
3 GW: 192.168.1.1
SEND  SEL

8
Programming MHD-201 Modules
• IP Address: Static IP address within the valid range of the local network to
which the module is connected.
• Network Mask: Local network mask.
• Default gateway: IP address of the default gateway on the local network to
which the module is connected.
 Date-Time: Displays data regarding time zone, date and time. Automatically it
presents the time zone depending on the country which has been entered.
2 - SETTINGS : Select this menu to access the following parameters:
 Input: Select one of the possible input combinations and the corresponding
parameters:
2 SD [CVBS+CVBS] ; 2 SD [HDMI+CVBS] ; 2 SD [SDI+CVBS] ;
1 HD [HDMI] ; 1 HD [SDI]
1  Time: 10.19
2 Date: 21.03.201
3 Time Zone: Europe / Madrid
SEND  SEL
1 General
2  Settings
3 USB Player
ESC SEL
1  Input
2 Output
ESC SEL
1  Input type
SD SDI + CVBS
2 Aspect 1 16:9
3 Codec 1: MPEG2
4 Bitrate Vi 1 : 8000
5 Bitrate Au 1 : 384
6 Low latency 1 :
OFF
7 Aspect 2 ---
8 Codec 2: ---
9 Bitrate Vi2 : ---
A Bitrate Au 2: ---
B Low latency 2: v
---
SEND  SEL

9
Programming MHD-201 Modules
 Aspect: Enables the image format to be selected, 16:9 or 4:3.
 odec: Enables the encoding standard of the digitized audio and video signal to be selected from the options:
MPEG2 and MPEG4 (if the input signal is SD, the default will encoding will be MPEG2, if the signal is HD, encoding is
H.264 (1080p resolution only supports MPEG4).
 Bitrate Video: (4-10 Mbits / s): The device can be configured for an input data encoding rate from 4 to 10 Mbits/s.
When selecting the encoding bitrate, the COFDM output bitrate must be taken into account, this should be sufficient to
support the encoding bitrate, in the opposite case the overflow alarm appears.
 Bitrate Audio: The device can be configured for an input data encoding rate of 96; 128; 160; 192; 224; 256; 320
and 384 Kbits/s.
 Low latency: Reduces encoding time for applications where response time is important (e.g. cameras). Selecting
the low-latency mode, has on the other hand decreased coding efficiency and image quality with a lot of movement.
 Output: The MHD-201 modulator has two output types CODFM and IP. Using
the SPI-300 control only the rst option can be congured, to select the IP mode
output use the web interface (see manual www.ikusi.tv).
• COFDM output: Select this option to specify the RF and Network Congu-
ration data.
• RF configuration: Select this option to specify the following output parame-
ters.
1 COFDM output
2 Service 1
3 Service 2
ESC SEL
1  RF Configuration
2 Network
ESC SEL
1 COFDM output
2 Channel: 21
3 Frequency: 474.000
4 Attenuation: 00.0 dB
5 Mode : 8K
6 Band Width: 8MHz
7 Guard Int.: 1/32
8 Constell. . 64QA
9 Code rate : 7/8
SEND  SEL

10
Programming MHD-201 Modules
 Channel: Enables the output channel to be selected and modified.
 Frequency: Reports on the output frequency of the current radio frequency carrier and enables its value to be
modified. The frequency value must lie within the valid range for VHF and UHF bands.
 Attenuation: Allows attenuation for the RF carrier signal to the output to be configured, varying this value in the
range of 0 dB to 25 dB.
 COFDM mode: Allows the OFDM mode to be configured, selecting 2K and 8K values.
 Bandwidth: Allows the bandwidth to be configured selecting the values 6, 7 or 8 MHz
 Guard interval: allows the guard interval to be configured by selecting 1/4, 1/8, 1/16 or 1/32 symbol.
 Constellation: enables the output modulation constellation to be configured by selecting from the options 16QAM
or 64QAM.
 Code rate: enables the redundant encoding rate to be configured selecting the values 1/2, 2/3, 3/4, 5/6 or 7/8.
• Network: Within this sub-data the data of the following parameters can be
congured:
 Network Name: Assigns a name to the network.
 Provider: Enables the name of the service provider to be specified.
 NID: Enables a value to be assigned to the network identifier.
 TSID: Enables a value to be assigned to the identifier of the transport stream or TS.
NOTE.
For a headend configuration with 2 or more devices, the TSID value must be different for each device.
 ONID: enables a value to be assigned to the original network identifier.
 NIT mode: OFF an LCN descriptor is not inserted in the NIT .
 NIT LCN: Enables the LCN mode of the NIT to be selected.
Europe Mode: Europe descriptor is inserted.
Independent Television Commission: UK descriptor to be inserted.
Nordig mode V1: Descriptor is inserted according to the Nordig V1 specification.
Nordig V2 mode: Descriptor is inserted according to the Nordig V2 specification.
Generic Mode: Generic LCN descriptor.
 Insert TDT-TOT: Enables information on the date and time to be inserted or not.
1  Name.: Standard
2 Provider: IKUSI
3 NID: 00001
4 TSID: 00021
5 ONID: 00100
6 NIT mode: ON
7 NIT LCN: OFF
8 Ins TDT-TOT : ON
SEND  SEL

11
Programming MHD-201 Modules
• Service: Depending on whether the Input conguration is in HD or SD
mode we can have one or two services respectively.
 Video: Enables the video signal of a service to be activated.
 Audio: Enables the audio signal of a service to be activated.
 LCN: Displays the logical channel number.
 SID: Enables the ID that is assigned to a service to be assigned, modified and identified. The SID value is important
for the detection of channels in some receivers. All SID values must be different for the group of services processed
by one or more devices that contribute to a common RF output.
 Name: Enables an identifying name to be assigned to each service.
3 - USB Player : The modulator allows video to be played through the USB port.
By means of an application, the user can customise a list of images and videos to
create a nal le ("video-nal.ts") capable of being reproduced as a proper chan-
nel.
• Status: Reports whether the channel is in USB playback mode or not.
 STOPPED: Playback paused.
 PLAYING: Playing on.
 USB ERROR: USB not detected.
 ERROR FILE: The final file is not correct.
• Mode: Enable / disable play ON / OFF .
1  Service 1
2 Video 1: ON
3 Audio 1: ON
4 LCN 1: 1
5 SDI 1: 21
6 Name 1: MAC SERV1
SEND  SEL
1 General
2 Settings
3USB Player
ESC SEL
1  Status STOPPED
2 Mode : OFF
SEND  SEL

12
MDHD-201 F 02.18
CH 21
SYSTEM: OK
1 General
2 Settings
3 Info
4 Language SEL
1 Detect
2 Send
3 Update (only via web)
ESC  SEL
4 Recall
5 Save
6 Factory Reset
ESC   SEL
1 configuration: 0001
2 See
3 Clear
SEND   SEL
7 About ...
ESC  SEL
SPI-300
vXX.XX (DD/MM/YY)
Copyright 2009
IKU SI OK
1 Input
2 Output
3 Country
ESC  SEL
4 Language
5 Advanced
ESC  SEL
1 Status
2 Alarm
3 Details
ESC SEL
CH1 VID: X Not detected
AUD: X Stereo
CH2 VID: X Not detected
AUD: X Stereo OK
Player. STOPPED
% Free: 00 <00 <00
Bitrate: 00.000MbpS
IP Bitrate: 00.000MbpS
Num Str: 1
OK
HW: 0 In: X Cod: X
Yes: X Mod : 0 IP: 0
Syn: X
STOP
MHD-201
HW: 01.00 SW: 02.18
BS: 01.00
OK
SERIAL: 385433545676
MAC: 0009E3545676
OK
1 General
2 Settings
3 USB Player
ESC SEL
1 Input: SD SDI + CVBS
ESC SEL
1 Channel: 21
2 Attenuat. : 0dB
ESC SEL
1 COFDM output
ESC SEL
1 Country: UK
SEND   SEL
1 Language: English
SEND   SEL
1 IP
2 Date-Time
ESC SEL
1 Input
2 Output
ESC SEL
1 Status STOPPED
2 Mode : OFF
SEND  SEL
QUICK MENUS
 • English 
 French 
 Spanish 
  Italian  

13
1 IP: 192.168.1.6
2 MR: 255.255.255.0
3 GW: 192.168.1.1
SEND   SEL
1 Time: 10.19
2 Date: 21.03.201
3 Time Zone: Europe / Madrid
SEND   SEL
1 COFDM output
2 Service 1
3 Service 2
ESC SEL
1 RF Configuration
2 Network
ESC SEL
1 Service 1
2 Video1: OFF
3 Audio1: OFF
4 LCN1: 1
5 SDI1: 42
6 Name 1: TEST1
SEND   SEL
1 Service 2
2 Video2: OFF
3 Audio2: OFF
4 LCN2: 2
5 SDI1: 43
6 Name 2 MAC SERV2
SEND   SEL
1 COFDM output
2 Channel: 21
3 Frequency: 474.000
4 Attenuation: 00.0 dB
5 Mode : 8K
6 Band Width: 8MHz
7 Guard Int.: 1/32
8 Constell. . 64QA
9 Code rate : 7/8
SEND SEL
1 Name.: Standard
2 Provider: IKUSI
3 NID: 00001
4 TSID: 00021
5 ONID: 00100
6 NIT mode: ON
7 NIT LCN: OFF
8 Ins TDT-TOT : ON
SEND   SEL
1 IP
2 Date-Time
ESC SEL
1 Input
2 Output
ESC SEL
1 Status STOPPED
2 Mode : OFF
SEND  SEL
1 Input type
SD SDI + CVBS
2 Aspect 1:16:9
3 Codec 1: MPEG2
4 Bitrate Vi 1 : 8000
5 Bitrate Au 1 : 384
6 Low latency1 : OFF
7 Aspect 1 ---
8 Codec 2: ---
9 Bitrate Vi2 : ---
A Bitrate Au2: ---
B Low latency2: ---
SEND  
SEL

SPI-300 / MHD-201 (v.A)
(EN)
Ángel Iglesias, S.A.
Paseo Miramón, 170
20014 San Sebastián, Spain
Tel [phone]
Fax [phone]
[email protected]
www.ikusi.tv