Iluminar DE CMH FIXTURE User manual

1000W
USER
MANUAL
DE CMH FIXTURE MODEL
1000W 208-277V
877-540-5588
iluminarlighting.com
[email protected]
IL-CMHDE1000-240

© Copyright 2022, ILUMINAR Lighting
Subject to change without notice.
2
Make sure the power cord is correctly connected and the lamp is securely in place.
Disconnect the fixture from the power supply prior moving the unit or performing any maintenance or
lamp changes.
DO NOT open the ballast case, it will void the warranty.
DO NOT support the ballast by power cord(s). These cords/connections are not designed to bear weight.
DO NOT make contact with the interior of the socket while power is on.
DO NOT attempt to rewire, alter, modify or reconfigure your system - this will void the ILUMINAR
warranty and could create serious safety hazards, or cause bodily injury or death, as this is a high
amperage and voltage device.
DO NOT submerge in water.
DO NOT plug the system into untested or unidentified voltage other than what is designated on ballast.
DO NOT CONNECT A CMH BALLAST to a Flip Box. It will void the warranty and can cause electrical
failure within the CMH Ballast. Flip or Switch Boxes are not recommended for any CMH Units or for any
high wattage ballasts.
DO NOT plug or unplug the lamp cord while the ballast is connected to power.
Make sure to wear proper gloves to protect from the transfer of oil from the skin to the lamps glass
surface.
When changing out the lamp, make sure that the lamp has time to cool before touching.
Make sure the lamp is correctly locked into the socket, properly securing the lamp.
If the lamp is damaged in any way (cracked, loose internal connections) replace the lamp immediately.
Keep away from Children. This product contains delicate electronic components. If it is placed near
an object that transmits radio signals, it could cause interference (i.e.: mobile devices, walkie talkies,
CB radios, remote controls and microwaves). If interference occurs, move such objects away from the
appliance.
WARNINGS
THANK YOU for purchasing an ILUMINAR Lighting CMH FIXTURE. We strive to deliver the best
customer service alongside world-class products and we go above and beyond to make sure you are
satisfied with your purchase. The following is a general set of warnings and basic guidelines for the
ILUMINAR Lighting CMH DE Fixture. Always have an expert install your product(s).
KEEP ORIGINAL PACKAGING
In the event of a return, products will need to be in the original ILUMINAR Lighting packaging to avoid
product damage during shipping. Any damage to products not in their original packaging will not be
covered under the Warranty. Visit iluminarlighting.com/warranty for more detailed information.
SAFETY 1ST
FAILURE TO OBSERVE THE FOLLOWING WARNINGS COULD RESULT IN ELECTRICAL SHOCK AND
SERIOUS INJURY. Additionally, failure to follow these safety warnings can/will result in a void of all
warranties as well as any manufacturer liability.
Please read carefully prior to beginning installation.

3
1-877-540-5588
iluminarlighting.com
[email protected]
MOUNTING & COVERAGE
DIMENSIONS
Lamp Not Included.
DE FIXTURE
1000W
CMH
SKU:VOLTAGE:
IL-CMHDE1000-240208-277V
Minimum
1.2m / 4’
1.2m / 4’
601mm / 23.6”
249mm / 9.8”
235mm / 9.26”
1.5m / 5’
TECHNICAL SPECS
PHYSICAL SPECIFICATIONS
Input Current
Case Length
5.10A
564mm
249mm
601mm
6.6kg
208V
4.60A
22.22"
9.80"
23.66"
14.55lb
240V
3.85A
270V
Input Power
Case Width
1045W
Rated Voltage
Height
Weight
208-277V
Voltage Range 187-290V
Ignition Voltage 5KV
THD <15%
Min Power Factor 0.95
Crest Factor 1.7
Input Connection IP67 Wieland Plug
Frequency 50-60HZ
Operation frequency 140-220HZ
Relative Humidity 95% (Non-condensing)
Operation Temp 0 - 35°C / 32-95°F
Recommended Lamp ILUMINAR CMH 1000W DE
Socket Type Lamp Base K12x30s - / Style
Minimum Mounting Height 1.2m / 4’
Energy efficient
Uniform Light Distribution
Soft Start Technology
Ignition Failure Protection

© Copyright 2020, ILUMINAR Lighting
Subject to change without notice.
4
PLEASE READ CAREFULLY PRIOR TO INSTALLATION
INSTALLATION
PROCEDURE
When possible, have a licensed electrician or electrical expert install all
fixtures or aid in the electrical layout plans and/or diagrams prior to
installation.
Check the electrical panel to ensure proper voltage is available for the
number of fixtures installed. Panels should only support a total amperage
of 80% of its capacity. (100 amp panel should never exceed 80 amps).
1. Find a suitable location for the fixture with sufficient cooling and away
from heat sources.
2. Use the included hanging cables to hang the fixture.
3. Ensure the fixture is hung completely level to the ground. A fixture that
is not level can burn the lamp emitter incorrectly leading to shorter
lamp life, poor lamp performance and/or lamp failures.
4. Install the lamp into the roll-lock socket (instructions pages 6-7) using
soft cotton or surgical gloves.
5. Plug the power cord into the power source (electrical outlet).
6. For proper lamp break-in, we recommend that you run the fixture at
100% power for at least 100 straight hours after initial startup. This
will improve lamp life and performance.
7. Set your desired dimming ratio. NOTE: the ballast dims or raises
output gradually to protect the lamp, so you may not see an instant
increase upon changing your output percentage.
RATED VOLTAGE 208-277V
VOLTAGE RANGE +/- 10% 187-290V
FREQUENCY 50 - 60Hz
OPERATIONS FREQUENCY 140-220HZ
PERFORMANCE
REQUIREMENTS
COMPATIBILITY Compatible with all ILUMINAR Lighting CMH DE lamps as well as the
ILUMINAR Lighting Touch & ILUMINAR Lighting HASH Environment
controllers.
© Copyright 2022, ILUMINAR Lighting
Subject to change without notice.

5
1-877-540-5588
iluminarlighting.com
[email protected]
• Turn the dimming dial to cycle through the dimming levels.
• If your lamp fails to start immediately, DO NOT cycle the power on
and off. This can damage the lamp and ballast.
• If after 30 minutes your lamp is still not lit, shut off power to the
ballast, and reconnect.
• This will begin the startup sequence again.
• Until the lamp has achieved at least 100 hours of operation, the lamp
should never be turned off prior to running at least 15 minutes. In
case this happens, WAIT 1 hour before igniting the lamp again.
IT IS VERY IMPORTANT that the lamp is given adequate time to cool
down before it is reignited. Allow a hot lamp to cool for 1 hour before
you try to restrike it. Hot re-strikes cause permanent lamp failure and
lumen output degradations. The lamp should never be turned off before
the lamp reaches full intensity, this may shorten its lifespan.
DO NOT install fixtures in areas of high heat, such as an attic, tent or
closed closet. Mount units at least 24-60 inches apart.
1. End of Lamp Life (EOL) Protection
2. Short Circuit Protection
3. Open Circuit Protection
4. Ignition Failure Protection
5. Thermal Protection
6. Suitable for ILUMINAR Lighting Touch+ Controller
7. Suitable for HASH Controller / 0-10V Control
8. Total Control Range 50-115%
DIMMING
CASE LENGTH 564mm 22.22”
CASE WIDTH 249mm 9.80”
HEIGHT 601mm 23.66”
WEIGHT 6.6kg 14.55 lbs
PHYSICAL
SPCIFIC
1. Max. allowable case temperature: 35º C / 95º F
2. Ambient Temperature: 0 - 35°C / 32-95°F
3. Max. Humidity: 95%
4. Ignition Voltage: 5kV
CARE
HOT RESTRIKE
MOUNTING
LOCATION
BALLAST
PROTECTIONS

© Copyright 2020, ILUMINAR Lighting
Subject to change without notice.
6
FIXTURE DIAGRAM
PROTECTIONS
WIRING DIAGRAM
RJ14 Controller Connection
Wieland Female
Wieland Male
NAME VOLTAGE SKU DIAGRAM
Power Cord Wieland Female to Male 120V IL-WLDCRD-120V
Power Cord Wieland Female to Male 240V IL-WLDCRD-240V
Power Cord Wieland Female to Male 277V IL-WLDCRD-277V
Power Cord Wieland Female to Male 347V IL-WLDCRD-347V
Ballast
Power Connection
Reflector
Arm
Soquet
Microprocessor Driven
End of Lamp Life (EOL)
Open Circuit Protection
Ignition Failure Protection
Thermal Sensing Protection
© Copyright 2022, ILUMINAR Lighting
Subject to change without notice.
5m

7
1-877-540-5588
iluminarlighting.com
[email protected]
RJ14-RJ14
SKU:
IL-CB-RJ1414
RJ14
RJ9
RJ14
RJ9-RJ14
Include it
RJ14 Splitter
SKU: IL-ADPT-SPLIT
123
RJ14-RJ14 10 ft / 3m
SKU:IL-CCRD-RG14-10
RJ14-RJ14 5ft / 1.5m
SKU: IL-CB-RJ914
RJ14 Splitter
SKU:
IL-CCRD-RG14-10
12
33
1
2
2
2
RJ14
RJ14
RJ14
22
1
1
1
1
RJ14-RJ14
SKU:
IL-CB-RJ1414
RJ14
RJ9
RJ14
RJ9-RJ14
Include it
RJ14 Splitter
SKU: IL-ADPT-SPLIT
123
RJ14-RJ14 10 ft / 3m
SKU:IL-CCRD-RG14-10
RJ14-RJ14 5ft / 1.5m
SKU: IL-CB-RJ914
RJ14 Splitter
SKU:
IL-CCRD-RG14-10
12
33
1
2
2
2
RJ14
RJ14
RJ14
22
1
1
1
1
TOUCH CONTROLLER DAISY CHAIN DIAGRAM
HASH CONTROLLER DAISY CHAIN DIAGRAM

8
1-877-540-5588
iluminarlighting.com
[email protected]
Lamp Loose in Socket Ensure the lamp is fully inserted into the socket and that
it has been properly locked.
Incorrect Voltage Make sure you’re using the correct input voltage with
ballast. If using incorrect voltage, disconnect the ballast
from the power source immediately.
Defective or Improper Wiring
Examine wiring to ensure it agrees with wiring diagrams
on ballast label. Check connections to see that they are
secure. If wiring a ballast, DO NOT use a neutral. The
correct wiring is two hot wires and a ground.
Poor electrical connections Check wiring and lamp contact with socket.
Incorrect Lamp Verify that you’re using a correct wattage lamp.
Lamp Damage Investigate possibility of outer lamp damage. Look for
broken tubes or loose metal replace lamp.
Possible Cause Corrective Maintenance
For more warranty information, visit
iluminarlighting.com/warranty
This guide does not supersede national, state, or local regulations for
electrical installations.
WARRANTY
CERTIFICATIONS
When properly used, this unit will provide you with years of
service. The ballast is covered under a 3 year warranty and the
lamp has a 1 year warranty. This warranty will be voided if the
unit is misused, abused, opened or altered. Warranty repair or
replacement will be at the sole discretion of the manufacturer.
Defective units need to be returned to the place of purchase with
proof of purchase/receipt.
RETURNS Please contact your point of purchase store for returns.
TROUBLESHOOTING
Follow these troubleshooting solutions: