Iluminar IL-5x26FSG-120 User manual

USER
MANUAL
iL5x MODEL 440W
1-877-540-5588
iluminarlighting.com
[email protected]
IL-5x26FSG-120
IL-5x26FSG-480
iL5x
LED Lighting Solutions

3
2
CONTENTS
• Observe all safety precautions (see page 10), seek the services of a
qualified electrician, installation professional, or call ILUMINAR Lighting
technicians for assistance.
• DO NOT handle or touch the fixture while in use.
• Connect the fixture only to the power sources of the appropriate voltage
using the correct AC plug type. Protect power cables from being pinched,
walked on, or otherwise damaged. Be especially careful where the power
cable enters the power outlet to the unit. Only connect the fixture to an
electrical outlet or extension cord of comparable standard and level
rating. Connect the fixture ONLY to the power sources of the correct
voltage using the plug received.
• The fixture should only be cleaned as directed. Always seek service for
your system by qualified service personnel if any of the following occur:
1. The fixture shows a noticeable change in performance.
2. The powersupply cord or plug is damaged.
3. The fixture has been dropped, or the exterior is damaged.
Please read this manual thoroughly prior to
installing or operating the ILUMINAR iL5x.
1-877-540-5588
iluminarlighting.com
[email protected]
© Copyright 2021, ILUMINAR Lighting
Subject to change without notice.
Pre-Install Information ........................................
Technical & Physical Specifications ......................
Hardware & Accessories ....................................
Instructions .......................................................
Daisy Chain Instructions .....................................
PPFD Map .........................................................
Important Cautions & Warranty ..........................
2
3
4
5-6
7
8-9
10
LED Lighting Solution
1067 mm / 42”
1003 mm / 39”
129 mm / 5”
PPF
Efficacy
Input Current
Input Power
Output Voltage
Output Power
Min Power Factor
THD
Crest Factor
BTU
Rated Mains Voltage
Mains Frequency
Dimmable
Ambient Temperature
Max. Temperature
Relative Humidity
Plug Type
Color Temperature
Color Rendering Index
Finishing Mounting Height
Emitter Cooling
Light Distribution +/- 5%
Waterproof Rating
LED Lifespan (90% of Life)
1144 µmol/s
2.6 µmol/j
12.20A
440W
33V
402.6W
0.9
< 20%
0.99
1460
120-277V AC / 347-480V AC
50 / 60Hz
0-10V Controllable
-20..+45°C
75°C/167°F
98%
Power Cord Sold Seperately
4000k
88
6”-12” to top of Canopy
Passive / Extruded Case
125º
IP65 for Damp/Wet Conditions
55,000+ hours
TECHNICAL SPECIFICATIONS
PHYSICAL SPECIFICATIONS
Length
Width
Height
Weight
1067mm
1003mm
129mm
13.5kg
42.01"
39.49"
5.08"
29.76lbs
VOLTAGE AND AMPERAGE
120V
208V
240V
277V
347V
480V
1.3A
0.94A
3.78A
2.16A
1.87A
1.63A
449W
442W
452W
445W
443W
440W
MODEL: WATTS: 440W
2.6
200-480V
VOLTAGE: 100-277V
SKU: IL-5x26FSG-480
IL-5x26FSG-120
MOUNTING & COVERAGE
1.2m / 4'
1.2m / 4'
15-30cm / 6-12”
iL5x 440W LED SPECTRUM
W
A
VELENGTH NM
© Copyright 2021 ILUMINAR Lighting
Subject to change without notice.

4
HARDWARE AND ACCESSORIES
The iL5x can be hung from rope
ratchets or can be mounted to a
rack.
Before you begin installation,
check that you have all the
necessary parts to begin.
1 iL5x Fixture
4 Rope Ratchets
IN THE BOX
1-877-540-5588
iluminarlighting.com
[email protected]
5
Lay the central mast on a flat table top or surface with the
attachment brackets facing UP. Attach each LED Bar by aligning the
plastic clips and carefully sliding them into place until you hear a
soft click.
CONNECTION INSTRUCTIONS
Once the plastic clips are all snapped in place, attach the A/C cables
coming from the mast to each LED bar by aligning the connector pins and
pressing the ends together. Lock by twisting in opposite directions.
Once all the LED bars are fastened into place and A/C cables are attached
to the mast, turn the fixture over (this may require more than one person).
Ensure the flat surface is clear of anything that could damage the delicate
diodes.
SLIDE
2
1
3
! CAUTION when handling your ILUMINAR iL Fixture.
The LED array should NOT come in contact with sharp
objects. DO NOT touch diodes or apply direct force to
the diodes as this can/will cause permanent damage.
© Copyright 2021, ILUMINAR Lighting
Subject to change without notice.

7
61-877-540-5588
iluminarlighting.com
[email protected]
HANGING INSTALLATION DAISY CHAIN CONNECTIONS
If you plan to utilize several LEDs in your room or facility, one of the many
benefits of the ILUMINAR LED is that you can “daisy chain” one fixture to another
to save space and use only one outlet to run several lamps, thus minimizing the
amount of cords used in your space.
If you plan to utilize the ILUMINAR HASH Controller, you can connect the connections
from the controller to the fixture and then connect the Daisy Chain Controller Cable
from fixture to fixture. Please consult with our lighting layout designers to ensure proper
spacing of outlets for your unique setup.
© Copyright 2021, ILUMINAR Lighting
Subject to change without notice.
1
4
A/C INPUT
(to power outlet)
Controller Cable
(to Controller)
AVAILABLE CABLES
A/C INPUT
(to power outlet)
Controller
Daisy Chain Cable
Controller Cable
(to Controller)
A/C Daisy
Chain Cable
1
4
2
3
Lift the LED and attach the
carabiners to pre-installed hooks
from ceiling or mounting beam. The
Ratchets should be installed closest
to the LED (and not the ceiling).
A: Remove slack to raise fixture.
B: Give slack to lower fixture.
To suspend mount, attach the 4 rope ratchets that come packaged with
this fixture to the LED.
Once fixture is hanging with all LED bars installed, connect the LED
Power Cable from the outlet to the fixture.
1
2
A
B
3

1-877-540-5588
iluminarlighting.com
[email protected]
9
8
PPFD MAP
© Copyright 2021, ILUMINAR Lighting
Subject to change without notice.
Clearance
Qty
Average PPFD
Max PPFD
Min PPFD
Median PPFD
Min/Average
Watts
0.5
1
678.06
911
286
775.5
42.18
440
ft
u
μmol/m2/s
μmol/m2/s
μmol/m2/s
μmol/m2/s
%
W
Clearance
Qty
Average PPFD
Max PPFD
Min PPFD
Median PPFD
Min/Average
Watts
1
1
541.39
777
250
564.5
46.18
440
ft
u
μmol/m2/s
μmol/m2/s
μmol/m2/s
μmol/m2/s
%
W
Clearance
Qty
Average PPFD
Max PPFD
Min PPFD
Median PPFD
Min/Average
Watts
Clearance
Qty
Average PPFD
Max PPFD
Min PPFD
Median PPFD
Min/Average
Watts
Clearance
Qty
Average PPFD
Max PPFD
Min PPFD
Median PPFD
Min/Average
Watts
Clearance
Qty
Average PPFD
Max PPFD
Min PPFD
Median PPFD
Min/Average
Watts
1.5
1
433.06
618
277
433.5
52.42
440
3
1
230.08
296
100
240
43.46
440
4
1
161.09
192
124
160
76.98
440
5
1
116.42
133
96
115.5
82.46
440
ft
u
μmol/m2/s
μmol/m2/s
μmol/m2/s
μmol/m2/s
%
W
ft
u
μmol/m2/s
μmol/m2/s
μmol/m2/s
μmol/m2/s
%
W
ft
u
μmol/m2/s
μmol/m2/s
μmol/m2/s
μmol/m2/s
%
W
ft
u
μmol/m2/s
μmol/m2/s
μmol/m2/s
μmol/m2/s
%
W
>=1000 762-1000 581-762 443-581 338-443 258-338 196-258 150-196 <150
Legend
PPFD MAP iL5x at 0.5ft
PPFD MAP iL5x at 1ft
PPFD MAP iL5x at 1.5ft PPFD MAP iL5x at 5ft
PPFD MAP iL5x at 4ft
PPFD MAP iL5x at 3ft

CAUTION
1. Leave at least one inch of space between the fixture and the mounting
area for maximum performance and lifespan.
2. ALWAYS wear protective eye wear when looking directly at the diodes to
prevent eye damage.
3. Only handle, clean or move fixture when it’s unplugged and completely
cool.
4. Keep the fixture free of dust, debris, deposits to ensure the maximum
potential of the fixture.
5. NEVER use cloth to clean the diodes. This will scratch the diodes and could
potentially break or dislodge them.
6. DO NOT use chemicals to clean the fixture. Use ONLY low pressure air or
low pressure water to remove dust and debris.
7. Do not exceed 70% max load for breakers due to inrush current in LED
fixtures
At ILUMINAR, we stand behind our products and our
technology as well as our customers. All ILUMINAR fixtures
are backed by our 5-Year Guarantee. Please visit our website
iluminarlighting.com/warranty for more information.
1-877-540-5588
iluminarlighting.com
[email protected]
GUARANTEE
Please read the following list carefully prior to beginning installation.
10