Iluminar IR328 Series User manual

Head Office
16107 Kensington Drive
#124 Sugar Land
Texas 77479 USA
Tel: [phone]
Fax: [phone]
e-mail: [email protected]
www.iluminarinc.com
ilumina
r
IR328 Series Infra Red
&
WL197 Series White Light
Illuminators
User’s Guide

Head Office
16107 Kensington Drive
#124 Sugar Land
Texas 77479 USA
Tel: [phone]
Fax: [phone]
e-mail: [email protected]
www.iluminarinc.com
ilumina
r
Overview
Congratulations on purchasing your new IR328 / WL197 illuminator. This light-weight and
compact IR328 / WL197 illuminator is the most powerful, yet fully eye-safe LED illuminator on
the market today.
The newly invented ultra high power LEDs and Plano-Convex Matrix lens assembly ensure the
maximum illumination distance. It is the perfect way to maximize the viewing range of your
night vision and gives an overall boost in security performance.
IR328 / WL197 illuminators are specifically designed to maximize thermal efficiency throughout
the unit. The optimum thermal management maintains low LED operating temperature, thus
resulting in long projected working life up to 10 years.
IR328 / WL197 illuminators use high efficiency LEDs and advanced control methods to deliver
extremely low electrical consumption. They are energy saving and deliver huge savings in
running costs compared to traditional bulb illuminators together with zero maintenance. Some of
the design features are;
▪3 modes of operation;
- Manual on/off
- Auto on/off mode with Photo Diode sensor
- Remote on/off
▪Weather proof design, high quality Engineering Plastic housing with Aluminum extrusion
rear heat sink
▪Military type circular connector
▪External Photo diode sensitivity adjustment

Head Office
16107 Kensington Drive
#124 Sugar Land
Texas 77479 USA
Tel: [phone]
Fax: [phone]
e-mail: [email protected]
www.iluminarinc.com
ilumina
r
Precautions & Handling
▪Operation
The factory setting is Auto mode (on/off by photo diode). For other modes of operation, the 3-way switch
located at the back of unit may be repositioned accordingly. Connect power cable to the circular
connector and refer to connector pin map for wiring.
▪Storage
Do not use or store the illuminator outside the specified temperature conditions or where it is subject to
strong vibration.
▪Cleaning
Remove foreign object on connector.
Remove soil, dust, or foreign object from external surfaces of the product using a soft cloth.
Use alcohol-based cleaning solvents such as isopropyl alcohol to clean, if necessary.
▪Precaution
Do not apply excessive voltage (Use only the specified voltage). Otherwise, you may get an electric shock
or a fire may occur.
In case of abnormal operation/ fault symptoms, contact your authorized iluminar dealer.
Package
▪IR328 / WL197 illuminator ▪Power Cable

Head Office
16107 Kensington Drive
#124 Sugar Land
Texas 77479 USA
Tel: [phone]
Fax: [phone]
e-mail: [email protected]
www.iluminarinc.com
ilumina
r
Usages
A. Power mode selection switch
3 modes of operations are possible by selecting appropriate 3-way toggle switch locations.
The factory setting is Auto mode (on/off by photo diode).
OFF / Remote “OFF” unless shorting pin B and C of circular connector
by “external switch” or “PIR motion detection sensor”, etc.
ON Manually turn-on the unit
Auto ON / OFF by photo sensor automatically
Power mode switch
OFF / Remote
ON
Auto mode

Head Office
16107 Kensington Drive
#124 Sugar Land
Texas 77479 USA
Tel: [phone]
Fax: [phone]
e-mail: [email protected]
www.iluminarinc.com
ilumina
r
B. Adjusting light sensor sensitivity
The factory setting value of “Light Sensor Sensitivity” is at level 6. However, the user may change
the sensitivity setting manually as below;
▪Preparation
- 3mm metric hexagonal wrench
- Philips head screwdriver with a small tip
▪Procedure
- Remove button head screw with the 3mm metric hexagonal wrench.
- Photo diode sensitivity trimmer should be exposed through the hole.
Clockwise rotation for less sensitivity (Unit automatically turns-on at darker ambient lighting)
- Using Philips head screwdriver, turn the trimmer to desired setting.
- Assemble button head screw back to its original position
Button head screw
Photo diode sensitivity trimmer

Head Office
16107 Kensington Drive
#124 Sugar Land
Texas 77479 USA
Tel: [phone]
Fax: [phone]
e-mail: [email protected]
www.iluminarinc.com
ilumina
r
Specifications
- Illumination: LED, λ=850 nm, 15 super LEDs for 30°, 20 super LEDs for 120°
- LED Collimation: 30° or 120°
- Dimensions: 7.48” x 6.69” x 2.95” (190 x 170 x 75mm)
- Weights: 2.2lb (1.0kg)
- Environments: CE / IP66
- Temp. Range: -40oto 120oF (-40oto 50oC)
- Cooling: Natural convection
- Power input: 24VAC
IR328-A30-24: 32 Watts
IR328-A120-24: 42 Watts
WL197-30-24: 42 Watts
WL197-120-24: 48 Watts
- Controls: Power on/off mode selection, Photo diode sensitivity control
- Illumination distance
IR328-A30-24: 328’ / 100m Infra-red
IR328-A120-24: 98’ / 30m Infra-red
WL197-30-24: 197’ / 60m White Light
WL197-120-24: 60’ / 18m White Light

Head Office
16107 Kensington Drive
#124 Sugar Land
Texas 77479 USA
Tel: [phone]
Fax: [phone]
e-mail: [email protected]
www.iluminarinc.com
ilumina
r
Outline Drawing

Head Office
16107 Kensington Drive
#124 Sugar Land
Texas 77479 USA
Tel: [phone]
Fax: [phone]
e-mail: [email protected]
www.iluminarinc.com
ilumina
r
Connector
- Connector Model: MS3112E-10S-6P
24VAC Pin Map
PIN Description PIN Description
A E_GND D AC24_H
B EXT_SIG E AC24_N
C COM F Auxiliary
12VDC (Optional) Pin Map
PIN Description PIN Description
A E_GND D DC_+12V
B EXT_SIG E DC_GND
C COM F Auxiliary
Note: Shorting pins “B” and “C” by external switch, PIR motion detection sensor, etc. will turn the unit ON
remotely when 3-way switch position is at OFF/Remote position.
Version: Dec. 2009