Iluminar iL9X Series User manual

USER
MANUAL
iL9X MODEL 1000W
1-877-540-5588
iluminarlighting.com
[email protected]
IL-9X26FSG-120
IL-9X26FSG-480

2
CONTENTS
• Observe all safety precautions (see page 8), seek the services of a
qualified electrician, installation professional, or call ILUMINAR Lighting
technicians for assistance.
• DO NOT handle or touch the fixture while in use.
• Connect the fixture only to the power sources of the appropriate voltage
using the correct AC plug type. Protect power cables from being pinched,
walked on, or otherwise damaged. Be especially careful where the power
cable enters the power outlet to the unit. Only connect the fixture to an
electrical outlet or extension cord of comparable standard and level
rating. Connect the fixture ONLY to the power sources of the correct
voltage using the plug received.
• The fixture should only be cleaned as directed. Always seek service for
your system by qualified service personnel if any of the following occur:
1. The fixture shows a noticeable change in performance.
2. The power-supply cord or plug is damaged.
3. The fixture has been dropped, or the exterior is damaged.
Please read this manual thoroughly prior to
installing or operating the ILUMINAR iL9X.
Pre-Install Information ........................................
Technical & Physical Specifications......................
Hardware & Accessories ....................................
Connections & Hanging Instructions ....................
Daisy Chain Connections .....................................
Daisy Chain Instructions ......................................
Precautions & Warranty ....................................
2
3
4
5 - 7
8 - 9
10 -11
12
1-877-540-5588
iluminarlighting.com
[email protected]
© Copyright 2020, ILUMINAR Lighting
Subject to change without notice.
3
LED Lighting Solution
iL9X LED SPECTRUM
W
A
VELENGTH NM
1067mm / 42”
1003mm / 39.4”
129mm / 5”
PHYSICAL SPECIFICATIONS
Length
Width
Height
Weight
1067mm
1003mm
129mm
18.58kg
42.01"
39.49"
5.08"
40.96lbs
VOLTAGE AND AMPERAGE
120V
208V
240V
277V
347V
480V
2.95A
2.12A
8.5A
4.86A
4.21A
3.64A
1015W
990W
1018W
1001W
994W
985W
Rated Mains Voltage
Voltage Range (+/-10%)
PPF
Efficacy
Input Current
Input Power
Output Voltage
Output Power
Min Power Factor
THD
Crest Factor
BTU
Mains Frequency
Dimming Type
Dimmable
Ambient Temperature
Max. Temperature
Relative Humidity
Color Temperature
Color Rendering Index
Finishing Mounting Height
Emitter Cooling
Light Distribution +/- 5%
Waterproof Rating
LED Lifespan (90% of Life)
2600 µmol/s
2.6 µmol/J
27.60A
1000W
33
910.8W
0.9
< 20%
0.99
3400
50 / 60Hz
0-10V Controllable
10 V-Source
-20..+45°C
75°C/167°F
98%
4000k
88
6-12” to top of Canopy
Passive / Extruded Case
125º
IP65 for Damp/Wet Conditions
55,000+ hours
TECHNICAL SPECS
347-480V AC
200-480V
120-277V AC
200-480V
MODEL: WATTS: 1000W2.6
200-480V
VOLTAGE: 100-277V
SKU: IL-9x26FSG-480IL-9x26FSG-120
MOUNTING & COVERAGE
1.5m/ 5'
15-30cm / 6-12"
1.5m / 5'

4
HARDWARE AND ACCESSORIES
The iL9X can be hung from steel
cables or can be mounted to a
rack.
Before you begin installation,
check that you have all the
necessary parts to begin.
1 iL9X Fixture
1 Power Cable
4 Steel Hanging Cables with attached
cylindrical locks for hanging
IN THE BOX
1-877-540-5588
iluminarlighting.com
[email protected]
CONNECTION INSTRUCTIONS
Lay the central mast on a flat table top or surface with the
attachment brackets facing UP. Attach each LED Bar by aligning
the plastic clips and carefully sliding them into place until you
hear a soft click.
Once the plastic clips are all snapped in place, attach the A/C
cables coming from the mast to each LED bar by aligning the
connector pins and pressing the ends together. Lock by twisting in
opposite directions.
Once all the LED bars are fastened into place and A/C cables are
attached to the mast, turn the fixture over (this may require more
than one person). Ensure the flat surface is clear of anything that
could damage the delicate diodes.
SLIDE
2
1
3
5
© Copyright 2020, ILUMINAR Lighting
Subject to change without notice.
! CAUTION when handling your ILUMINAR iL Fixture.
The LED array should NOT come in contact with sharp
objects. DO NOT touch diodes or apply direct force to the
diodes as this can/will cause permanent damage.

7
61-877-540-5588
iluminarlighting.com
[email protected]
Attached the secure hooks to the fixture.
Loop the hanging wire as shown around the support beam (as shown in Figure
A). Press down at base of hook to slide to adjust the mounting height of the
fixture (Figure B).
HANGING INSTALLATION
Once fixture is hanging with all LED bars installed, connect the power cable
(blue tip) from the outlet to one side of the fixture.
1
2
3
FIGURE A
FIGURE B
© Copyright 2020, ILUMINAR Lighting
Subject to change without notice.
1
4
A/C INPUT
(to power outlet)
Controller Cable
(to Controller)
Power Supply
AC INPUT
Controller
Cable
Led Bar´s

1-877-540-5588
iluminarlighting.com
sales@iluminarlighting.
9
8
DAISY CHAIN CONNECTIONS
AVAILABLE CABLES
© Copyright 2020, ILUMINAR Lighting
Subject to change without notice.
9
If you’re planning to utilize several LEDs in your room or facility, one of the many
benefits of the ILUMINAR LED is that you can “daisy chain” one fixture to another to
save space and use only one outlet to run several lamps thus minimizing the amount of
cords used in your space.
If you plan to utilize the ILUMINAR HASH Controller, you can connect the
yellow connections from the controller to the fixture and then connect the
Daisy Chain Controller Cable from fixture to fixture. Please consult with our
lighting layout designers to ensure proper spacing of outlets for your unique
setup.
- Up to 1 iL9x Fixtures may be connected in series at 120V AC
- Up to 3 iL9x Fixtures may be connected in series at 277V AC
1
A/C INPUT
(to power outlet)
Controller
Daisy Chain Cable
Controller Cable
(to Controller)
A/C Daisy
Chain Cable
1
4
2
3

1-877-540-5588
iluminarlighting.com
sales@iluminarlighting.
11
10
DAISY CHAIN SPECIFICATION
© Copyright 2020, ILUMINAR Lighting
Subject to change without notice.
1-877-540-5588
iluminarlighting.com
[email protected]
11
8.5A on 20A / 120V
Breaker Load: 42.5%
Do not Exceed 70%
Max Load for Breaker
9.72A on 20A / 208V
Breaker Load: 48.6%
Do not Exceed 70%
Max Load for Breaker
11.8A on 20A / 277V
Breaker Load: 59%
Do not Exceed 70%
Max Load for Breaker
10.92A on 20A / 277V
Breaker Load: 54.6%
Do not Exceed 70%
Max Load for Breaker
12.69A on 20A 480V
Breaker Load: 63.45%
Do not Exceed 70%
Max Load for Breaker
Breaker Needed 20A
Breaker Needed 20A
Breaker Needed 20A
Breaker Needed 20A
Breaker Needed 20A
Breaker Needed 20A
Hardwired Terminal
Connection
8.5A
8.5A x 1 Fixtures = 8.5A on 20A / 120V = 42.5% Load
4.86A x 2 Fixtures = 9.72A on 20A / 208V = 48.6% Load
4.21A x 3 Fixtures = 12.63A on 20A / 240V = 57.8% Load
4.86A
4.21A
4.86A
4.21A ...
3.64A
2.95A
2.12A
3.64A
2.95A
2.12A
...
...
...
3.64A x 3 Fixtures = 10.92A on 20A / 277V = 54.6% Load
2.95A x 4 Fixtures = 11.8A on 20A / 277V = 59% Load
2.12A x 6 Fixtures = 12.72A on 20A / 480V = 63.6% Load
11.56A on 20A / 240V
Breaker Load: 57.8%
Do not Exceed 70%
Max Load for Breaker
120V Daisy Chain Up to 1 Fixtures
208V Daisy Chain Up to 2 Fixtures
240V Daisy Chain Up to 4 Fixtures
347V Daisy Chain Up to 7 Fixtures
277V Daisy Chain Up to 5 Fixtures
480V Daisy Chain Up to 9 Fixtures
70% Max Load for Circuit Breakers, limit is due to Inrush Current
in High End Commercial LED Fixtures
70% Max Load for Circuit Breakers, limit is due to Inrush Current
in High End Commercial LED Fixtures
! !

12
CAUTION
1. Leave at least one inch of space between the fixture and the
mounting area for maximum performance and lifespan.
2. ALWAYS wear protective eye wear when looking directly at the
diodes to prevent eye damage.
3. Only handle, clean or move fixture when it’s unplugged and
completely cool.
4. Keep the fixture free of dust, debris, deposits to ensure the maximum
potential of the fixture.
5. NEVER use cloth to clean the diodes. This will scratch the diodes and
could potentially break or dislodge them.
6. DO NOT use chemicals to clean the fixture. Use ONLY low pressure
air or low pressure water to remove dust and debris.
7. Do NOT exceed 70% max load for breakers due to Inrush current in
LED fixtures.
Please read the following list carefully prior to beginning installation.
At ILUMINAR, we stand behind our products and our
technology as well as our customers. All ILUMINAR fixtures
are backed by our 5-Year Guarantee. Please visit our website
iluminarlighting.com/warranty for more information.
1-877-540-5588
iluminarlighting.com
[email protected]
GUARANTEE