Ingenico IWL 250 User manual

Download Guide for IWL 250
How do I download the OS and Baseline file from a USB device for my
Telium?
For iWL250 devices, you will need an accessory cable that does not come with the unit or
base for this. The cable can be ordered from hardware providers. It will be a male micro
USB to female USB adapter cable.
Follow these instructions to download the OS and Baseline for a Telium device:
Downloading the OS and Baseline files
1. Download the OS and Baseline to your PC.
o iCTxx Native OS/BASELINE files located here.
o iCTxx Universal App OS/Baseline files located here.
o iWLxx Native OS/BASELINE files located here.
o iWLxx Universal App OS/Baseline files located here.
2. Unzip the files to a folder on your PC
3. Place the unzipped OS and Baseline files inside of a folder called TELIUM.
4. Copy the TELIUM folder and its contents to the USB drive. It must be in the topmost directory in
the USB drive.
Clear the OS and Baseline from the device
1. Power cycle the device by pressing the yellow Clear key and the '#' key at the same time.
2. For battery-powered Telium's, press the Enter key to power them back on. For other units, skip
to step 3.
3. Immediately press and hold the F1 key until a "*" appears.
4. Immediately press the F4 key until another "*" appears.
5. Immediately press the Down arrow until another "*" appears.
6. Finally press the Up arrow until you see "****" on the screen.
7. LLT will appear on the screen.
Installing files from the USB drive
1. Plug the USB stick with the OS and Baseline in to the Telium device.
2. Reboot the terminal by pressing the yellow Clear key and the '#' key at the same time.
3. For battery-powered Telium's, press the Enter key to power them back on. For other units, skip
to step 4.
4. Immediately press and hold the F4 key.
5. USB MASS STORAGE will appear on the screen, then the applications that can be installed will be
displayed.
6. Select the appropriate application to install and press the Enter.
7. Your device will start installing the component selected.

8. Repeat steps in this section to download the Baseline application after you complete the OS
download.
How do I configure the Telium TMS Screen for IP Remote Download?
**Note: If using a 16MB iCT or iWL (Splash screen will say *A98 instead of *C98), you
must 'Delete SW' from TADU prior to completing the steps below, click here for those
steps**
Note: Close batch prior to completing download, failure to close or delete the batch will result in
a failed parameter download.
Complete steps in order below:
TADU 202 download:
1. iWLs Only (For iCTs, jump to next step):
1. Ensure the Ethernet cable is plugged into the cradle (base).
2. Place the device on the cradle.
3. Initialize the cradle, click here for those steps (if already initialized, move to next step)
2. From the Idle screen, press the Function key.
3. Type in the password, (1, Function, 1, 1, 1, 1, 1, 1, 1).
4. Highlight TADU and press Enter.
5. Highlight ADVANCED CFG and press Enter.
6. Highlight PACKET SIZE and press Enter.
7. Highlight 4K and press Enter.
8. Highlight Configure and press Enter.
9. Highlight Full and press Enter.
10. Highlight Ethernet and press Enter.
11. Highlight Dynamic and press Enter.
12. The device will display Enter IP Address. Type in 63.241.142.219 (press '#' for a '.') and press
Enter.
13. The device will display Enter Port. Type in 8013 and press Enter.
14. Highlight Off and press Enter.
15. The device will display Enter Model. Type in TELIUM (press the corresponding number key to
the letter you need until that letter displays) press Enter.
16. The device will display Enter App Name. Type in TADU202 and press Enter.
17. The device will display Enter Terminal ID. Type in the site ID TADU202 and press Enter. (note:
only one download can be in progress per site ID at a time. If TADU202 comes up with error
Terminal Not Available, please use TADU203 through TADU220 instead. The App Name remains
unchanged.)
o Site IDs available for use: TADU101, TADU202, TADU203, TADU204, TADU205,
TADU206, TADU207, TADU208, TADU209, TADU210, etc.

18. Highlight Download and press Enter. The download will progress at 10% intervals and will
display a '*' at each interval.
19. When the download is complete the device will go back to the Idle screen.
OS and Baseline download:
1. iWLs Only (For iCTs, jump to next step):
1. Ensure the Ethernet cable is plugged into the cradle (base).
2. Place the device on the cradle.
3. Initialize the cradle, click here for those steps (if already initialized, move to next step)
2. From the Idle screen, press the Function key.
3. Type in the password if the device prompts, (1, Function, 1, 1, 1, 1, 1, 1, 1).
4. Highlight TADU and press Enter.
5. Highlight ADVANCED CFG and press Enter.
6. Highlight PACKET SIZE and press Enter.
7. Highlight 4K and press Enter.
8. Highlight Configure and press Enter.
9. Highlight Full and press Enter.
10. Highlight Ethernet and press Enter.
11. Highlight Dynamic and press Enter.
12. The device will display Enter IP Address. Type in 63.241.142.219 (press '#' for a '.') and press
Enter.
13. The device will display Enter Port. Type in 8013 and press Enter.
14. Highlight Off and press Enter.
15. The device will display Enter Model. Type in TELIUM (press the corresponding number key to
the letter you need, then the Function key until you get the appropriate letter) and press Enter.
16. The device will display Enter App Name. Type in IWLOSB9123 (press the corresponding number
key to the letter you need, then the Function key until you get the appropriate letter) and press
Enter.
17. The device will display Enter Terminal ID. Type in the site ID IWL202 and press Enter.
o Site IDs available for use: IWL201, IWL202, IWL203, IWL204, IWL205, IWL206, IWL207,
IWL208, IWL209, IWL210 (note: only one download can be in progress per site ID at a
time. If IWL202 comes up with error Terminal Not Available, please use IWL201 through
IWL210 instead. The App Name remains unchanged.)
18. Highlight Delete SW and press Enter.
19. Enter password 246135 and press Enter.
20. Select Remove All W/ Reload (1)
21. Select 'Yes' to the following two prompts
22. Terminal will reboot and start the download.
23. When the download is complete the device will go back to the Idle screen.
Configuring the TMS Screen for IP Download

1. Press the F key to access the Function Menu
2. Select 0 (Telium Manger)
3. Select 3 (Initialization)
4. Select 1 (Parameter)
5. Press the F4 key to arrow down, and then Select T.M.S
6. Select IP/Eth
7. Select SSL= No
8. Select IP ADDRESS, Enter IP 63.241.142.236, and then press Enter key
9. Enter Port number 2600, then press Enter key
10. Enter TID, and then press Enter key
11. Select Off for Protected Download, and then press Enter key
12. Press Cancel twice to return to the Main Menu
Remote Download Procedure
1. Press the F key to access the Function Menu
2. Select 0 (Telium Manger)
3. Select 2 (Evolution)
4. Select 2 (Remote Load)
5. Leave Software NR blank and press Enter key