Insportline IN 14171 Galicum User manual

USER MANUAL –EN
IN 14171 Elliptical Trainer inSPORTline Galicum

2
CONTENTS
SAFETY INSTRUCTIONS....................................................................................................................... 3
PRODUCT SPECIFICATION .................................................................................................................. 4
ASSEMBLE PART LIST.......................................................................................................................... 4
OTHER COMPONENTS......................................................................................................................... 6
PART LIST............................................................................................................................................... 7
ASSEMBLY STEPS ................................................................................................................................ 8
EXPLODED DRAWING......................................................................................................................... 17
PART LIST............................................................................................................................................. 18
COMPUTER OPERATION INSTRUCTIONS........................................................................................ 24
BASIC INFORMATION...................................................................................................................... 24
START WINDOWS AND STARTING................................................................................................ 24
KEY FUNCTION ................................................................................................................................ 25
PROGRAM FUNCTION ........................................................................................................................ 26
P1 –MANUAL MODE........................................................................................................................ 26
P2 –RANDOM MODE....................................................................................................................... 26
P3 –WEIGHT LOSS MODE.............................................................................................................. 26
P4 –CV WORKOUT MODE.............................................................................................................. 26
P5 –HILL INTERVALS MODE.......................................................................................................... 27
P6 –FITNESS TEST MODE ............................................................................................................. 27
P7 –HRC 1 MODE............................................................................................................................ 27
P8 –HRC 2 MODE............................................................................................................................ 27
P9 –USER 1 MODE.......................................................................................................................... 28
P10 –USER 2 MODE........................................................................................................................ 28
PROFILE FIGURE................................................................................................................................. 29
BLUETOOTH COMPUTER APP (iOS&Android) OPERATION INSTRUCTIONS................................ 29
FOR iOS DEVICE (iPAD) .................................................................................................................. 29
FOR ANDROID DEVICE ................................................................................................................... 31
TERMS AND CONDITIONS OF WARRANTY, WARRANTY CLAIMS................................................. 34

3
SAFETY INSTRUCTIONS
When using this product, the following basic precautions should always be followed. Please read the
instructions carefully before using this product.
DANGER
Always unplug this product from the electrical outlet immediately after using it and also before
cleaning. You will avoid the risk of an electric shock.
WARNING
To reduce the risk of burns, fire, electric shock or physical injury:
1. When you insert the plug, please pay attention to its condition to avoid danger.
2. Step onto the machine before using it, not the other way around. Take out the plug if you are
not using the machine.
3. To avoid any danger, disabled people must be supervised while using the machine.
4. People with impaired physical, senses or mental capabilities (including children) or someone
less experienced cannot use this machine without supervision. Children cannot use the
machine.
5. Incorrect or excessive training may endanger your health.
6. Be sure to use the product only for its intended purpose as described in this manual. Do not
use any attachments not recommended by the manufacturer in order to avoid danger or
accidents.
7. Never operate the product if the cord or plug was damaged, if it is not working properly, or if
it was dropped into water. Please return the product to the service center of the seller for
examination and repair.
8. Do not carry this product by the supply cord or use the cord as a handle.
9. Keep the cord away from hot surfaces.
10. Never operate the product with the air vents blocked. Keep the air vents free of lint, hair, etc.
11. Never drop or insert any objects into any vent of the product. No adjustable part should stand
out and limit the user’s movements.
12. Do not use this machine outdoors.
13. Please put this product on flat surface or platform.
14. Keep a minimal safety area of 0,6 m around the machine.
15. Do not operate where aerosol (spray) products are being used or where oxygen is thin.
16. Before turning the product power off, turn off all the controls and then remove the plug from
the outlet.
17. Connect the product to a properly grounded outlet only.
18. This product only can be used for commercial purposes.
19. Please check the machine regularly to confirm if it is damaged or not, you’ll be ensuring its
long-term safety.
20. The brake system is controlled by the speed under the watts mode. Under any other mode, it
is not dependent on speed.
21. Stride length: 510 mm. Weight of the flywheel: 14.5 kg.

4
22. Weight limit: 150 kg.
23. Category: SA (according to EN957 norm) suitable for professional and/or commercial using.
24. WARNING! The heart rate frequency monitoring may not be completely accurate.
Overexertion during training can lead to a serious injury or even death. If you start to feel
faint, stop the exercise immediately.
PRODUCT SPECIFICATION
CAUTION: According to this manuals guidance, the machine is operated while the user sits on the
machine and faces the computer.
User Weight
330 lbs / 150 kg
Size
214.5 x 172.5 x 63 cm
G.W.
98 kg
N.W.
88 kg
Power Spec.
15V/1A DC, power supplier (power charger)
ASSEMBLE PART LIST
A. Frame
B. Control tube
C. Computer

5
D. Rear stabilizer
E. Swing pole (L/R)
F. Handrail tube (L/R)
G. Pedal (L/R)

6
OTHER COMPONENTS
H. Middle tube cover
I. Neck cover
J. Hand grip decorative
cover
K. Bent tube cover
L. Post decorative cover
M. Rear stabilizer
N. Pedals
P. Rear decorative cover
Q. Screw cover
R. Power supplier
S. Forefoot stabilizer
T. Cup holder assembly

7
PART LIST
STEP
ITEM
Description
Qty
STEP
ITEM
Description
Qty
Step1
K01
CKS hex screw M10X55
6
Step5
K17
Truss hex screw M8X20
2
K02
Spring washer M10
6
K18
Washer Ø8.5XØ30X2.0t
2
K03
Washer Ø10XØ30X3.0t
4
K20
CKS hex screw M12X35
2
K04
Truss cross screw M5X10
2
K21
Nylon nut M12
2
K05
Washer Ø5XØ10X1.0t
2
Step6
K22
Carriage screw M8X45
4
K06
Truss cross screw M5X10
8
K23
Nylon nut M8
4
K38
Washer Ø10XØ16X1.0t
2
Step7
Step8
K24
Truss cross screw M5X10
20
Step2
K07
Truss hex screw M8X15
2
K36
Truss cross screw Ø4X16
2
K08
Washer Ø8XØ25X2.0t
2
K37
Truss cross screw M5X12
6
K10
Truss cross screw M5X12
6
Step9
K25
Truss cross screw M5X10
8
Step3
K11
CKS hex screw M8X15
1
K26
Washer Ø5XØ10X1.0t
8
K12
Washer Ø8XØ25X2.0t
1
tool
K27
L shaped hex wrench
10x43x103mm
1
K13
CKS hex screw M10X70
2
K28
L shaped hex wrench
8x75x150mm
1
K14
Washer Ø10XØ20X1.0t
4
K29
L shaped hex wrench 6mm
1
K15
Nylon nut M10
2
K30
L shaped hex wrench
5x25x67mm
1
K35
Truss cross screw M5X15
4
K31
L shaped hex wrench
+cross screwdriver
5x40x180mm
1
K36
Truss cross screw Ø4X16
2
K32
Bushing wrench+cross
screwdriver 13+17mm
1
Step 4
K16
Truss cross screw M5X12
8
K33
Lug shaped wrench
19+13mm
1
K34
Opened wrench 10mm
1
K39
PHILIPS SCREWDRIVER
1

8
ASSEMBLY STEPS
Step. 1 –Frame and stabilizer assembly
1 Tighten the rear stabilizer (D) and the frame (A) with screws (K01), spring washers (K02) and
washers (K03, K38).
2 Tighten the front stabilizer cover set (S) and the rear stabilizer cover set (M) on the frame (A)
with screws (K06).
3 Cover with rear decorative cover (P) and tighten with screws (K04) and washers (K05).
CAUTION: While affixing the rear stabilizer cover, please confirm that they match each other and if the
rear stabilizer cover has locked onto the iron tube.

9
Step 2 –Pedals and frame assembly
1. Affix the bending tube cover (K, S) onto the left fitness pedal (G-L) and tighten it with
screws (K10). Then attach the left fitness pedal (G-L) to the crank shaft of the left frame
and tighten it with screws (K07) and washers (K08).
2. Affix the bending tube cover (K, S) to the right fitness pedal (G-R) and tighten it with
screws (K10). Then attach the right fitness pedal (G-R) to the crank shaft of the right
frame and tighten it with screws (K07) and washers (K08).
CAUTION: Make sure the foot pedal iron tube and the crank shaft are tightened well to avoid possible
accidents caused by loose connections.

10
Step 3 –Control tube and frame assembly
1 Attach the control tube (B) to the middle tube cover (H). Then please attach the control iron
tube to the frame iron tube and affix the front and the sides of the iron tube with screws and
washers (K11, K12, K13, K14, K15).
2 After connecting the control wire, push the middle tube cover (H) down and affix it.
3 Affix the cup holder assembly (T) to the control tube (B) with screws (K35, K36).
CAUTION:
•The assembly should be carried out by two people, one to grip the control tube, and the
other to assemble the control tube and frame and then tighten the screws.
•After fixing the screws, please connect the control signal wire while paying attention to the
wires’direction, do not force them into each other.
•After connecting the wires, press on the control tube plastic and affix it.
•While tightening the screws, please be careful to not drop the screws into the frame.

11
Step 4 –Control tube and computer assembly
1. Connect the wires as showed below. Pay attention to the direction and do not force them into
each other.
2. Match the screw holes on back of computer (C) with the screw holes on the control tube and
tighten computer with screws (K16). During assembly, please confirm that the screws are
fixed to avoid any damage to the computer.
3. At last, tighten the neck cover (I) with screws (K16) so that it doesn’t press onto the wires.
CAUTION:
•Make sure the computer faces the right direction.
•The computer wire must be matched with the computer shelf’s hole to avoid the wires bending
and causing a short-circuit.

12
Step 5 –Poles assembly
1. Place the washer (K18), wave washer (K19) as shown below, then attach the upper end tube
of left handrail (E-L) to the iron core of the control tube and tighten it with screws (K17).
2. Assemble the left lower side after finishing the left upper side assembly. Match the lower end
plate on the left handrail to the end of the fitness pole, then tighten with screws (K20, K21).
3. Place the washer (K18) and wave washer (K19) as shown below, then attach the upper end
tube of the right handrail (E-R) to the iron core of the control tube and tighten it with screws
(K17).
4. Assemble the right lower side after finishing the right upper side assembly. Match the lower
end plate of the right handrail to the end of the fitness pole, then tighten with screws (K20,
K21).
CAUTION:
•The handrail sets differ, please see the marks on the handrails to avoid incorrect assembly.
•While assembling the handrail and the fitness pedal, you may need to squat down. Please pay
attention to the iron tubes to avoid impact and danger.

13
Step 6 Swing pole and handrail tube assembly
1. Attach the end of the handrail tube (F-L) to the iron tube on the upper end of the swing pole,
then tighten it with screws (K22, K23).
2. Attach the end of the handrail tube (F-R) to the iron tube on the upper end of the swing pole,
then tighten it with screws (K22, K23).
CAUTION: The left & right handrail tubes are different, please see the marks on the handrails to avoid
incorrect assembly.

14
Step 7 –Swing pole covers assembly
Put the hand grip decorative cover (J) onto the hand grip tube’s rail and tighten it with screws (K24,
K36).
CAUTION:
When you lock the plastic covers, please confirm that they match and that they are tightened enough.

15
Step 8 –Swing tube and pedal tube covers assembly
1. Match the left S bending tube cover (K) to the front end of foot pedal iron tube and tighten with
screw (K37).
2. Then put the left shaft cover (L) on the left & right side of the handrail tube and match them
well, then tighten with screws (K24).
3. Match the right S bending tube cover (K) to the front end of the foot pedal iron tube and tighten
with screws (K37).
4. Then put the right shaft cover (L) on the left & right side of the handrail tube and match them
well, then tighten with screws (K24).
CAUTION: When you assemble the plastic covers, make sure thy match and that they are tightened
well.

16
Step 9 –Fitness pole and foot pedal assembly
1. Make the screw holes on the left foot pedal (N) match with the screw holes on the left fitness
pole, then cover them with washers (K26) and tighten with screws (K25).
2. Make the screw holes on the right foot pedal (N) match with the screw holes on the right
fitness pole, then cover them with washers (K26) and tighten with screws (K25).
CAUTION:
•When attaching the foot pedals, make sure they are locked to avoid them falling off because of
a loose screw.
•Pay attention to the direction of the pedals.
•K25 and K26 are made of stainless steel with plastic packaging.

17
EXPLODED DRAWING

18
PART LIST
NO
NUMBER
ITEM
QTY
NO
NUMBER
ITEM
QTY
(A)
1
C04
NT-3275
Idle wheel adjust
hook
1
A01
JED9-A1001
Frame assembly
1
C05
NT-3276
Idle wheel fixing
metal core
1
A02
PCT-003-2
Wheel belt(big)
Φ310<J10 belt use>
1
C06
SPA060-130-
10
Washer
Φ6xΦ13x1.0t
2
A03
SGA8-20I
C.K.S. hex screw
M8xP1.25x20
4
C07
SOC6
Nylon nut M6xP1.0
2
A04
SOC8
Nylon nut M8xP1.25
4
C08
SOA6
Screw nut M6xP1.0
1
A05
SGA8-20I
C.K.S. hex screw
M8xP1.25x20
1
C09
GH-6204ZZ
Bearing 6204ZZ
2
A06
SEA8-30
Hexagon screw
M8xP1.25x30
1
C10
SRA20
C shaped ring Φ20
shaft use
1
A07
CA-450J10
Belt 45"x10 grooves
1
(D) HED9-C4001
HED9-C4001
CRANK
TURNPLATE SET
1
A08
NFW-023
Φ242 double way
power supplier (with
NT-1683 shaft cover)
1
D01
JED9-C4001
Crank turnplate
assembly
2
A09
SGA6-20
C.K.S. hex screw
M6xP1.0x20
4
D02
P-3448
Plastic turnplate
2
A10
SPB6
Spring washer M6
4
D03
P-3449
Turnplate cover
2
A11
SPA060-130-
10
Washer Φ6xΦ13x1.0t
4
D04
SCI4-12
Truss cross self-
tapping screw Φ4x12
10
A12
XRB-069-004
Lower PC board
(PQ26-12A)
1
D05
SEA10-50I
Hexagon screw
M10xP1.5x50
2
A13
SCA5-10
Truss cross screw
M5xP0.8x10
2
D06
SOC10
Nylon nut M10xP1.5
2
A18
XL-682E
Power wire
1
D07
SPA100-200-
10
Flat washer
Φ10xΦ20x1.0t
4
A24
PB-01-002
Bearing wheel (without
bearing) Φ70XΦ8X28t
2
D08
SPB10
Spring washer M10
2
A25
SDA8-40
Truss hex screw
M8xP1.25x40ni
2
D09
SGA8-15
C.K.S. hex screw
M8xP1.25x15
2
A26
2
D10
SPA085-300-
20
Washer
Φ8.5xΦ30x2.0t
1
A27
SOC8
Nylon nut M8xP1.25 Ni
2
D11
BAA0200-
200-10
Foam grip
20mmX20mmX1.0t
16
A28
SOA8
Hex screw nut
M8xP1.25
8
D12
NO-5953
Crank fixing plate
1
A29
P-1820
Adjustment foot pad
4
(E)
FRAME OUTER
COVER SET
1
A30
SOF8A
Iron hex pulling nut
M8XP1.25(NHS-8125)
4
E01
P-3442L
Frame side cover - L
1

19
A31
BJ-48-330B
Belt 4.8x330mm black
6
E02
P-3442R
Frame side cover - R
1
A32
BJ-22-080B
Belt 2.2x80mm black
1
E03
SCI4-12
Round head cross
self-tapping screw
ψ4x12
4
A33
BJ-36-102B
Belt 3.6x102mm black
1
E04
SCA5-10
Truss cross screw
M5xP0.8x10
14
A34
XL-1577A
Battery Power Wire
1
E05
P-3443
Middle tube head
cover
1
A35
XB-074-002
Battery 12V 2.3Ah
1
E06
P-3444
Frame upper
decorative cover
1
A36
DED-F-380-
500
Cingulum 38X50
female
1
E07
P-3445
Frame middle
decorative cover
1
A37
DED-M-380-
500
Cingulum 38X50 male
1
E08
P-3465
Frame lower
decorative cover
1
A38
BJ-48-330B
Belt 4.8x330mm black
4
E09
P-3466
AV extension board
fixing base
1
(B) HED9-C1001
HED9-C1001 CRANK
SET
1
E10
P-3475
DC power board
1
B01
JED9-C1001
Crank set assembly
1
E11
P-3446L
Front stabilizer cover
- L
1
B02
NT-3047
Crank shaft bushing
1
E12
P-3446R
Front stabilizer cover
- R
1
B03
E13
P-3447L
Rear stabilizer cover
- L
1
B04
GH-6005ZZ
Bearing 6005ZZ
2
E14
P-3447R
Rear stabilizer cover
- R
1
B05
SQI08-08-25
Double round parallel
key 8X8X25
2
E15
SCI3-10
Truss cross self-
tapping screw Φ3x10
2
B06
E16
SOI5
Iron board screw nut
M5X25X13 black
3
B07
NT-3033
Middle axle sleeve
tube
1
E17
SCA5-15
Truss cross screw
M5xP0.8x15
3
B08
NT-3211
Middle axle sleeve
tube
1
(F) HED9-I1001
HED9-I1001 REAR
STABILIZER SET
1
(C) HED9-D1001
HED9-D1001 IDLE
WHEEL SET
1
F01
JED9-I1001
Rear stabilizer
assembly
1
C01
JED9-D1001
Idle wheel set
assembly
1
F02
SOA8
Hex screw nut
M8xP1.25X8T
4
C02
NT-1489
Idle wheel block
3
F03
P-1820
Adjustment foot pad
2
C03
SIA5-15IL
Counter sink hex
screw M5xP0.8x15
blue nylon patch
3
F04
SOF8A
Iron hex pulling nut
M8XP1.25 (NHS-
8125)
2
G05
F05
NAL-494
Wheel compression
board
4
G06
GH-6003ZZ
Bearing 6003ZZ
4
F06
SDA6-50S
Truss hex screw
M6XP1.0X50
stainless
8
G07
SRA17
C shaped ring Φ17
shaft use
4
F07
SPC060-190-
15-190
Arc washer
Φ6xΦ19x1.5t-R19 Ni
plating
16
G08
JED9-M1003
Pedal fixing plate
assembly
2
F08
BAA5750-
250-10
Foam sticker
575mmx25mmx1.0t
single side tape black
4

20
G09
NT-3048
Stabilizer shaft
bushing
2
F09
SOC6
Cap M6XP1.0
8
G10
F10
BAA-0004
Foam grip single
side tape black
4
G11
GH-6003ZZ
Bearing 6003ZZ
2
(G) HED9-M1001
HED9-M1001 FOOT
STEP IRON TUBE
SET
1
G12
GH-6904ZZ
Bearing 6904ZZ
2
G01
JED9-M1001
Foot step iron tube
assembly - L
1
G13
SEC10-45I
C.K.S. hex screw
M10xP1.5x45
2
G02
JED9-M1002
Foot step iron tube
assembly - R
1
G14
SPA100-200-
20
Flat washer
Φ10xΦ20x2.0t
2
G03
NT-3037
Pedal shaft
2
G15
SOC10
Nylon nut M10xP1.5
2
G04
G16
P-1728B
PU wheel Φ74X44
(with NAL-133)
4
J20
XEK-165
Sound inputting
JACK board
1
G17
GH-6003ZZ
Bearing 6003ZZ
8
J21
XL-826A
Sound inputting
JACK board
connecting wire
1
G18
SRA17
C shaped ring Φ17
shaft use
8
J22
XEK-170
Hom 4 Ω 2W 30X70
mm
2
G19
SPG170-240-
03
Wave washer
Φ17xΦ24x0.3t
4
J23
XL-850L
Left hom connecting
wire
1
(H) HED9-B1001
HED9-
B1001CONTROL
TUBE SET
1
J24
XL-850R
Right hom
connecting wire
1
H01
JED9-B1001
Control tube assembly
1
J25
XEK-168
PHONE JACK board
1
H02
BE-0300
Guide thread L=300
black
2
J26
XL-825A
PHONE JACK boarc
connecting wire
1
H03
PFA028-03-
0440
HDR foam grip -
Φ28X3.0tX440
2
J27
XEK-253
USB small board
1
(I) HED9-H1001
HED9-H1001 HAND
GRIP PULSE SET
1
J28
XL-1349
USB connecting wire
1
I01
P-3467
TPR handle bar
2
J29
SCI4-10
Truss cross self-
tapping screw Φ4x10
8
I02
P-3469
Handle bar hand grip
pulse board
2
J30
SAI3-8
Round head cross
self-tapping screw
ψ3x8
16
I03
P-3470
Knob + -
2
J31
RCC-750-
002
Sticker
1
I04
NO-5703
Hand grip pulse iron
plate
4
J32
RCC-750-
003
Sticker
1
I05
XEK-252
Keyboard
2
(L) HED9-Q7001
HED9-Q7001
SWING TUBE SET
1
I06
SAI3-6
Round head cross
self-tapping screw
Φ3x6
4
L01
JED9-Q7001
Swing tube assembly
- L
1
I07
SHA3-15S
Counter sink cross
screw M3xP0.5x15
stainless steel
4
L02
JED9-Q7002
Swing tube assembly
- R
1
I08
BAC0120-
120-03
Double side tape 12
mm x 12 mm x 0.3t
4
L03
GH-6305VV
Bearing 6305ZZ
2