Insportline IN 14170 User manual

USER MANUAL –EN
IN 14170 Elliptical trainer Gemini E200

2
CONTENTS
SAFETY PRECAUTIONS........................................................................................................................ 3
PARAMETERS........................................................................................................................................ 4
PARTS LIST............................................................................................................................................ 4
Screw bag............................................................................................................................................ 5
ASSEMBLY ............................................................................................................................................. 7
HOW TO USE........................................................................................................................................ 10
CONTROL PANEL ................................................................................................................................ 10
Display modes ................................................................................................................................... 11
Key functions...................................................................................................................................... 11
PROGRAMS.......................................................................................................................................... 11
Preset programs (P1 –P12).............................................................................................................. 11
Manual mode ..................................................................................................................................... 12
User mode.......................................................................................................................................... 13
Heart rate control mode..................................................................................................................... 13
Watts mode........................................................................................................................................ 15
PROGRAMS IN THE DOT MATRIX ..................................................................................................... 15
EXPOLDED DRAWING......................................................................................................................... 17
COMPONENTS LIST ............................................................................................................................ 18
TERMS AND CONDITIONS OF WARRANTY, WARRANTY CLAIMS................................................. 20

3
SAFETY PRECAUTIONS
You should always take basic precautions when using this product, including the following:
Please read these instructions carefully before using this product.
DANGER: Always unplug the product from the electrical outlet immediately after using it and
before cleaning and maintenance, otherwise you rick an electric shock.
WARNING: To reduce the risk of burns, fire, electric shock or other injury, always inspect the
plug before connecting it to the socket.
Before you use this machine, please step on it first and then start the machine. Do not act the
other way around.
Always turn the machine off if you are not using it.
To avoid any danger, close supervision is necessary when this product is used by children,
invalids or disabled people.
People with reduced mental or sensory capabilities (including children) cannot exercise on this
machine without supervision.
Children cannot use this product.
Incorrect or excessive training may be detrimental to your health.
Only use the product for the purposes it was made for. Do not use attachments that were not
recommended by the manufacturer to avoid dangerous situations and accidents.
Never operate the product if the cord or plug are damaged, if they are not working properly,
have been damaged, or dropped into water. Please return the product to the service center of
seller for examination and repair.
Do not carry this product by the supply cord or use the cord as a handle.
Keep the cord away from hot surfaces or ground.
Never operate the product with the air vents blocked. Keep the air vents free of lint, hair, etc.
Never drop or insert any objects into any vent of the product.
Do not use or operate the machine outdoors.
Please put this product on a flat surface or a platform.
Keep a 0.6 m safety area around the machine.
Do not operate the machine in places where aerosol (spray) products are being used or where
oxygen is thin.
Connect the product to a properly grounded outlet only.
Regularly check the machine for damage, you’ll increase its longevity.
The brake system is controlled by the speed under the Watts mode, but under any other
mode, it does not depend on speed.
Weight limit: 140 kg
Category: SA (EN 957) for professional or commercial use
WARNING: The heart rate monitoring system may be inaccurate. Over exercising may
result in serious injury or death. If you feel faint stop exercising immediately.

4
PARAMETERS
Dimensions before assembly
2122 x 624 x 1592 mm
Dimensions after assembly
2180 x 515 x 773 mm
Weight
97.1 kg
Stride length
510 mm
PARTS LIST
A. Console mast set
B. Main frame set
C. Front stabilizer set
D. Rear stabilizer set
E. Left swing tube set
F. Right swing tube set
G. Main frame front cover
(left/right)
H. Console mast decoration
cover (left/right)
I. Left swing shaft decoration
cover (front/rear)

5
J. Console set (LED)
K. Swing shaft decoration cover
(right/front; left/rear)
L. Left swing shaft lower
decoration cover (outer/inner)
M. Right swing shaft lower
decoration cover (outer/inner)
N. Console lower decoration
cover
P. Middle cover
Screw bag
ITEM
Description
Qty
ITEM
Description
Qty
K01
Truss inner hex screwM8xP1.25x25
4
K12
Nylon nut M10xP1.5
2
K02
Spring washer M8
4
K13
Truss cross screw M4xP0.7x12
16
K03
Washer Φ8xΦ16x1.5t
4
K14
Truss cross self-tapping screw
Φ4x16
16
K04
CKS inner hex steel screw
M8xP1.25x20
4
K15
Truss cross screw M5xP0.8x10
4
K05
Washer ∮8x∮12x1.0t
4
K16
Truss cross self-tapping screw
Φ4x20
3
K06
Wave washer∮25.6x∮33.7x0.3t
2
K21
L-shaped wrench+ cross opener 5mm
1
K07
Allen steel screw M10xP1.5x15
2
K22
Opening wrench 13mm+15mm
1
K08
Wave waherM10
2
K23
L-shaped wrench+ cross opener 6mm
1
K09
Washer φ10xφ30x2.0t
2
K24
Torx wrench
1
K10
Allen steel screwM10xP1.5x75
2
K25
Bushing wrench +cross opener
13mm+17mm
1
K11
Flat washerΦ10xΦ20x2.0t
4

6

7
ASSEMBLY
Step 1
Fix and fasten the main frame set (B) and the front and rear stabilizer (C, D) with screw (K01) and
spring washer (K02), washer (K03).

8
Step 2
According to the image, connect the relative wires, and assemble the console mast (A) to the main
frame set with screw (K04), washer (K05) to fix and fasten. And then, fix the main frame front cover
(G) to the main frame with screw (K14), and lock the console mast decoration cover (H) with screw
(K14). Finally, cover with the middle cover (P).
Step 3
According to the image, plug the wave washer (K06), and then plug the left & right handle bar set (E,
F) into the metal core of the console mast and fasten with screw (K07) and washer (K08, K09).

9
Next, connect the handle bar lower terminal to the end terminal of the interlock pedal, and ensure
them are fastened tightly with screw (K10), washer (K11) and screw nut (K12) abiding by the image.
According to the image, connect the middle and lower wires of the hand grip fast key, and please
notice the direction. When the direction is wrong, please do not plug compulsively. After the wires are
connected, please plug the rest wires into the console mast.
Step 4
Connect the console (J) with the wires of the console mast set. After that, fasten the console (J) with
screw (K15), and then fix and fasten the console lower decoration cover (N) with screw (K16).
Lean the shaft decoration cover set (K, I) to the horizontal tube of the handle bar tube set tightly and
fix with screw (K13).

10
Lean the swing lower decoration cover set (L, M) to the swing tube tightly and fix with screw (K13,
K14).
Attention: Please check whether the rubber covers match with each other, and whether the rubber
covers are connected tightly.
HOW TO USE
One after the other, step with your feet onto the pedals, firmly grab the handles and start
exercising
The display will show the current data. (Learn how to set the values and choose programs
below).
Get off the machine by first stepping off with only one foot and then the other.
CONTROL PANEL
This is a LED display console, and the functions shown include RPM, SPEED, TIME, CALORIES,
DISTANCE, WATTS, LEVEL, and dot matrix display of PROGRAM graph.