Insportline IN 9118 ET520i User manual

1
USER MANUAL –EN
IN 9118 Elliptical inSPORTline ET520i
Made in P.R.C

2
CONTENTS
SAFETY CAUTION............................................................................................................................................... 3
TOOL KIT .............................................................................................................................................................. 4
EXPLODED VIEW ................................................................................................................................................ 6
PARTS LIST........................................................................................................................................................... 7
ASSEMBLY ......................................................................................................................................................... 11
KNOWING THE ICONSOLE.............................................................................................................................. 21
TRAINING INSTRUCTION................................................................................................................................ 25
TERMS AND CONDITIONS OF WARRANTY, WARRANTY CLAIMS ....................................................... 27

3
PREFACE
This elliptical has been designed and constructed to provide maximum safety. Nevertheless, certain precautions
should be taken when using exercise equipment. Read the whole manual before assembling and using the
bicycle. The following safety precautions should also be observed:
SAFETY CAUTION
1. Before using the elliptical, please read all instructions in this manual.
2. It is the responsibility of the owner to ensure that all users of the elliptical are adequately informed of all
precautions. Use the elliptical only as described in this manual.
3. Use the elliptical indoors on a level surface and keep it away from moisture and dust. Place a mat under
the stabilizers to protect the carpet or floor.
4. Inspect and tighten all parts regularly. Replace and worm parts immediately.
5. Keep children away from this equipment at all times. DO NOT leave them unsupervised in the room
where this exerciser is kept.
6. Wear appropriate exercise clothing when using the elliptical. Do not wear loose clothing that could
become caught in the elliptical.
7. If you feel pain or dizziness while exercising, stop immediately and cool down.
8. The pulse sensor is not a medical device. Various factors including the user’s movement, may affect the
accuracy of the heart rate readings. The Pulse sensor is intended only as an exercise aid in determining
heart rate trends in general.

4
TOOL KIT
IMFD
F-2:HexboltM8*P1.0*20L(4)
F-14: FlatWasher Łp6*Łp16*1T(8)
F-13:SCREW M5*12L(8)
Box Spanner(1)
F-7:Flat washer for
8* 19*2T bolt(2) F-4;lock nut for M8 bolt (6)
F-5: Curved Washer 8* 19*2T (6)
Allen Key(1)
F-6:Carriage Bolt
M8*P1.25*40L (4)
F-11; Allen bolt
M8*P1.25*50L(2)
IMFD
F-1;FlatWasher 8* 25*2T bolt(4)
F-9;FlatWasher £p8*£p16*1T(2) F-12:
SCREW
M5*8L(4)
F-3:Curved Washer 20* 30*0.3T(2)
F-15ˇGˇ]2ˇ^
F-10; 16*36.5L bolt(2)
F-8:Carriage Bolt
M8*P1.25*55L (2)
F-20:Carriage Bolt
M8*P1.25*65L (2)
F-19ˇFAcorn nut M8(4)

5
1
1/1
IMFD
ŁpŁp
Box Spanner(1)
F-4;lock nut f orM8bolt( 6)
CurvedWasher
Allen Key(1)
F-6:Carriage Bol t M8*P1.25*40L(4)
F-11; Alle n bolt M8*P1.25*50L(2)
IMFD
F-1; 8* 25*2Tbolt(4)
ŁpŁp
F-3:CurvedWasher 20* 30*0.3T(2)
ˇGˇ]ˇ^
F-10; 16*36.5Lbolt(2)
F-8:Carriage Bol t M8*P1.25*55L(2)
F-18:Carriage Bol t M8*P1.25*60L(2 )
F-19ˇFAcornnutM8(4)
1
1/1
1/1
1/1
1/1
1/1
1/1
1/1

6
EXPLODED VIEW

7
PARTS LIST
NO.
DESCRIPTION
Q'TY
A
Computer
1
A-1
Screw
4
B
Handlebar post set
1 (set)
B-1
End cap for front handlebar
2
B-2
Foam grip for front handlebar
2
B-3
Hand pulse
2
B-4
Screw
2
B-5
Sleeve
2
B-6
Axle for handlebar
1
B-7
Flat washer
4
B-8
Semicircle washer
2
B-9
Cable wire (upper)
1
B-10
Spring washer
6
B-11
Screw
6
B-12
Screw
2
B-13
Hand pulse wire
2
B-14
Screw
2
B-15
Cover for handlebar post
1
C-L
Left upper handlebar
1 (set)
C-R
Right upper handlebar
1 (set)
C-1
End cap for upper handlebar
2
C-2
Foam grip for upper handlebar
2
D
Main frame
1 (set)
D-1
Cable wire (lower)
1
D-2
C-type ring
1
D-3
Flat washer
1
D-4
Wave washer
1
D-5
Screw for sensor box
1
D-6
Sensor box
1
D-7
Bearing
2
D-8
Belt
1
D-9
Screw
7
D-10
Chain cover (L)
1
D-11
Screw
4
D-12
Nut
2
D-13
Chain cover (R)
1

8
D-14
DC Wire
1
D-15
Adaptor
1
D-16
Brake knob
1
D-17
Nut
2
D-18
Axle for brake
1
D-19
Nut
2
D-20
Nylon nut
2
D-21
Flat washer
2
D-22
Screw
1
D-23
Flat washer
2
D-24
Nylon nut
1
D-25
Brake plate
1
D-26
Felt
1
D-27
Motor bracket
1 (set)
D-29
Axle of gear box
1
D-30
Screw
1
D-31
Nut
1
E
Eddy magnet assembly
1 (set)
E-1
Screw
2
E-2
Flat washer
2
E-3
Spring washer
2
F
Screw set
1 (set)
F-1
Flat washer
4
F-2
Nylon screw
4
F-3
Wave washer
2
F-4
Nylon nut
6
F-5
Semicircle washer
6
F-6
Carriage screw
4
F-7
Flat washer
2
F-8
Carriage screw
2
F-9
Flat washer
2
F-10
Bushing
2
F-11
Screw
2
F-12
Screw
4
F-13
Screw
8
F-14
Flat washer
8
F-15
Cover for screw
2
F-16
Bushing wrench
1

9
F-17
Hex wrench
1
F-19
Nut
4
F-20
Screw
2
G
Flywheel set
1 (set)
G-1
Flywheel
1
G-2
Nut
2
G-3
Nut
3
G-4
Flat washer
1
G-5
Bearing
1
G-6
Axle for flywheel
1
G-7
Bearing
1 (set)
G-8
Bushing
1
H
Front stabilizer set
1 (set)
H-1
Foot cap for front stabilizer
2
H-2
Nut
2
H-3
C-type ring
2
H-4
Transportation wheel
2
H-5
Bushing
2
H-6
Screw
4
H-7
Adjustable foot cap
2
I-L
Left pedal arm
1 (set)
I-R
Right pedal arm
1 (set)
I-1
Sleeve
4
I-2
End cap
2
I-4
Pedal connector
2
I-5
Flat washer
6
I-6
Screw
6
J
Idler
1 (set)
J-1
Hex. screw
1
J-2
Nylon nut
1
J-3
Flat washer
1
J-4
Spring
1
J-5
Spring bracket
1
J-6
Hex. screw
1
J-7
Flat washer
1
J-8
Hex. screw
1
J-9
Idler wheel
1
K-L
Left lower handlebar
1 (set)

10
K-R
Right lower handlebar
1 (set)
K-1
Screw
4
K-2
Sleeve
4
L-L
Left crank arm
1
L-R
Right crank arm
1
L-1
Screw
4
L-2
Flat washer
4
L-3
Fixed stick for wheel
2
L-4
Wheel
2
L-5
Bearing
4
L-6
Cover for wheel
2
L-7
Screw
4
L-8
Bushing
4
L-9
Wave washer
2
L-10
Nylon nut
2
L-11
Flat Washer
4
L-12
Bearing
4
L-13
Bushing
2
L-14
Hex. screw
2
L-15
Crank arm connect base
2
M
Linkage tube of rear stabilizer set
1 (set)
M-1
Linkage tube of rear stabilizer
2
M-2
Linkage sleeve of rear stabilizer
4
M-3
Fixed axle of folder
2
M-4
Foot cap
2
M-5
Screw
4
M-6
Left end cap
1
M-7
Right end cap
1
N
Axle set
1 (set)
N-1
Pulley
1
N-2
Axle
1
N-3
Hex. screw
3
N-4
Bushing
1
O
Disc cover and crank set
2 (set)
O-1
Crank (R+L)
2
O-2
Screw
10
O-3
Screw
2

11
O-4
Cover for disc cover
2
O-5
Disc cover
2
P-1
Front cover for upper handlebar
2
P-2
Rear cover for upper handlebar
2
P-3
Left cover for pedal arm
2
P-4
Right cover for pedal arm
2
P-5
Pedal
2
Q
Rear stabilizer set
1 (set)
Q-1
End cap
2
Q-2
Screw
4
Q-3
Rear stabilizer
1
Q-4
Foot cap
2
Q-5
Nut
2
ASSEMBLY
BEFORE EVERYTHING
It will affect your safety and the smoothness of this machine, as well as its life time.
Please check is there’s any parts missed.
Please assemble all the screws first
After everything fixed, then make sure they’re firmly enough.

12
BUILD IT
STEP 1
1. Securely fasten the Front stabilizer (H) to the Main frame (D) by using 2 Flat washers (F-7), 2 Carriage
screws (F-8), and 2 Nut (F-19).
2. Securely fasten the Rear stabilizer (M) to the Frame (D) by using 2 Semicircle washer (F-5), 2 Screws
(F-20), and 2 Nut (F-19).

13
STEP 2
1. Assemble the Left crank arm (L-L) to the Crank (O-1) by using 1 Flat washer (F-1), 1 Nylon screw (F-
2), and 1 Cover for screw (F-15).
2. Assemble the Right crank arm (L-R) to the Crank (O-1) by using 1 Flat washer (F-1), 1 Nylon screw (F-
2), and 1 Cover for screw (F-15).

14
STEP 3
1. Connect the Cable wire (upper) (B-9) to the Cable wire (lower) (D-1).
2. Install the Handlebar post set (B) to the main frame with 4 Flat washers (B-7), 2 Semicircle washers (B-
8), 6 Spring washers (B-10), and 6 Screws (B-11).
3. Install the Right lower handlebar (K-R) to the Axle for handlebar with 1 Flat washer (F-1), 1 Nylon
screw (F-2), and 1 Wave washer (F-3).
4. Install the Left lower handlebar (K-L) to the Axle for handlebar with 1 Flat washer (F-1), 1 Nylon screw
(F-2), and 1 Wave washer (F-3).

15
STEP 4
1. Attach the Left pedal arm (I-L) to the left crank arm, and then fasten it with 1 Pedal connector (I-4), 3
Flat washers (I-5), and 3 Screws (I-6).
2. Attach the Right pedal arm (I-R) to the right crank arm, and then fasten it with1 Pedal connector (I-4), 3
Flat washers (I-5), and 3 Screws (I-6).
3. Assemble the Left pedal arm (I-L) to the Lower handlebar (K-L) by using 1 Nylon nut (F-4), 1 Flat
washer (F-9), 1 Sleeve (F-10).
4. Assemble the Right pedal arm (I-R) to the Lower handlebar (K-R) by using 1 Nylon nut (F-4), 1 Flat
washer (F-9), 1 Sleeve (F-10).

16
STEP 5
Assemble the Pedals (P-5) with 8 Screws (F-13) and 8 Flat washers (F-14).

17
STEP 6
Assemble Left cover for pedal arms (P-3) and Right cover for pedal arms (P-4) with Screws (F-12).

18
STEP 7
1. Install the Left upper handlebar (C-L) to the Left lower handlebar (K-L) by using 4 Nylon nuts (F-4), 4
Semicircle washers (F-5), and 4 Carriage screws (F-6).
2. Install the Right upper handlebar (C-R) to the Right lower handlebar (K-R) by using 4 Nylon nuts (F-4),
4 Semicircle washers (F-5), and 4 Carriage screws (F-6).
3. Put the Front cover for upper handlebars (P-1) and Rear cover for upper handlebars (P-2) to the
Right/Left upper handlebars and fasten them with 4 Screws (K-1).

19
STEP 8
1. Plug the Cable wire (upper) (B-9) and Hand pulse wire (B-13) onto the back of Computer (A).
2. Install the Computer (A) to the computer panel which is welded on the top of the handlebar post. Fix the
computer with 4 screws (A-1).

20
FOLD FOR STORAGE & UNFOLD FOR USE
10 1
2
ABC
B
A
C
1. Make the two arrow icons of chain cover and disc to be alignment.
2. Tighten the knob by clockwise way.
3. Lift up linkage tube of rear stabilizer.
4. Fix the shaft into the hole, fold for storage.
5. Unfold for use- to do the reverse of what above steps.